This patch adds kernel side support for software breakpoint.
Design is that, by using an illegal instruction, we trap to hypervisor
via Emulation Assistance interrupt, where we check for the illegal instruction
and accordingly we return to Host or Guest. Patch also adds support for
software breakpoint in PR KVM.
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Now that AltiVec and hardware thread support is in place enable e6500 core.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

ePAPR represents hardware threads as cpu node properties in device tree.
So with existing QEMU, hardware threads are simply exposed as vcpus with
one hardware thread.

The e6500 core shares TLBs between hardware threads. Without tlb write
conditional instruction, the Linux kernel uses per core mechanisms to
protect against duplicate TLB entries.

The guest is unable to detect real siblings threads, so it can't use the
TLB protection mechanism. An alternative solution is to use the hypervisor
to allocate different lpids to guest's vcpus that runs simultaneous on real
siblings threads. On systems with two threads per core this patch halves
the size of the lpid pool that the allocator sees and use two lpids per VM.
Use even numbers to speedup vcpu lpid computation with consecutive lpids
per VM: vm1 will use lpids 2 and 3, vm2 lpids 4 and 5, and so on.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
[agraf: fix spelling]
Signed-off-by: NAlexander Graf <agraf@suse.de>

Since the guest can read the machine's PVR (Processor Version Register)
directly and see the real value, we should disallow userspace from
setting any value for the guest's PVR other than the real host value.
Therefore this makes kvm_arch_vcpu_set_sregs_hv() check the supplied
PVR value and return an error if it is different from the host value,
which has been put into vcpu->arch.pvr at vcpu creation time.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Occasional failures have been seen with split-core mode and migration
where the message "KVM: couldn't grab cpu" appears.  This increases
the length of time that we wait from 1ms to 10ms, which seems to
work around the issue.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

We currently decide at compile-time which of the SPE or AltiVec units to
support exclusively. Guard kernel defines with CONFIG_SPE_POSSIBLE and
CONFIG_PPC_E500MC and remove shared defines.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Powerpc timer implementation is a copycat version of s390. Now that they removed
the tasklet with commit ea74c0ea follow this
optimization.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NBogdan Purcareata <bogdan.purcareata@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch emulates debug registers and debug exception
to support guest using debug resource. This enables running
gdb/kgdb etc in guest.

On BOOKE architecture we cannot share debug resources between QEMU and
guest because:
    When QEMU is using debug resources then debug exception must
    be always enabled. To achieve this we set MSR_DE and also set
    MSRP_DEP so guest cannot change MSR_DE.

    When emulating debug resource for guest we want guest
    to control MSR_DE (enable/disable debug interrupt on need).

    So above mentioned two configuration cannot be supported
    at the same time. So the result is that we cannot share
    debug resources between QEMU and Guest on BOOKE architecture.

In the current design QEMU gets priority over guest, this means that if
QEMU is using debug resources then guest cannot use them and if guest is
using debug resource then QEMU can overwrite them.
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Move ONE_REG AltiVec support to powerpc generic layer.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Make ONE_REG generic for server and embedded architectures by moving
kvm_vcpu_ioctl_get_one_reg() and kvm_vcpu_ioctl_set_one_reg() functions
to powerpc layer.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Add AltiVec support in KVM for Book3e. FPU support gracefully reuse host
infrastructure so follow the same approach for AltiVec.

Book3e specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which of the SPE or
AltiVec units to support exclusively by using CONFIG_SPE_POSSIBLE and
CONFIG_PPC_E500MC defines. As Alexander Graf suggested, keep SPE and AltiVec
exception handlers distinct to improve code readability.

Guests have the privilege to enable AltiVec, so we always need to support
AltiVec in KVM and implicitly in host to reflect interrupts and to save/restore
the unit context. KVM will be loaded on cores with AltiVec unit only if
CONFIG_ALTIVEC is defined. Use this define to guard KVM AltiVec logic.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Increase FPU laziness by loading the guest state into the unit before entering
the guest instead of doing it on each vcpu schedule. Without this improvement
an interrupt may claim floating point corrupting guest state.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Add 'r' to register name r2 in kvmppc_hv_enter.

Also update comment at the top of kvmppc_hv_enter to indicate that R2/TOC is
non-volatile.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Book3E specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which unit to support
exclusively. As Alexander Graf suggested, this will improve code readability
especially in KVM.

Use distinct defines to identify SPE/AltiVec interrupt numbers, reverting
c58ce397 and 6b310fc5 patches that added common defines.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

SPE exception handlers are now defined for 32-bit e500mc cores even though
SPE unit is not present and CONFIG_SPE is undefined.

Restrict SPE exception handlers to e200/e500 cores adding CONFIG_SPE_POSSIBLE
and consequently guard __stup_ivors and __setup_cpu functions.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Guest visible debug register and hardware visible debug registers are
same, so ther is no need to have arch->shadow_dbg_reg, instead use
arch->dbg_reg.
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Dbsr is not visible to userspace and we do not think any need to
expose this to userspace because:
  Userspace cannot inject debug interrupt to guest (as this
  does not know guest ability to handle debug interrupt), so
  userspace will always clear DBSR.
  Now if userspace has to always clear DBSR in KVM_EXIT_DEBUG
  handling then clearing dbsr in kernel looks simple as this
  avoid doing SET_SREGS/set_one_reg() to clear DBSR
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch changes the default behavior of MSRP_DEP, that is
guest is not allowed to change the MSR_DE, to guest can change
MSR_DE. When userspace is debugging guest then it override the
default behavior and set MSRP_DEP. This stops guest to change
MSR_DE when userspace is debugging guest.
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This patch adds "rfdi" instruction emulation which is required for
guest debug hander on BOOKE-HV
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Debug interrupt can be either "critical level" or "debug level".
There are separate set of save/restore registers used for different level.
Example: DSRR0/DSRR1 are used for "debug level" and CSRR0/CSRR1
are used for critical level debug interrupt.

Using CPU_FTR_DEBUG_LVL_EXC to decide which interrupt level to be used.
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

In the beggining was on_each_cpu(), which required an unused argument to
kvm_arch_ops.hardware_{en,dis}able, but this was soon forgotten.

Remove unnecessary arguments that stem from this.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Using static inline is going to save few bytes and cycles.
For example on powerpc, the difference is 700 B after stripping.
(5 kB before)

This patch also deals with two overlooked empty functions:
kvm_arch_flush_shadow was not removed from arch/mips/kvm/mips.c
  2df72e9b KVM: split kvm_arch_flush_shadow
and kvm_arch_sched_in never made it into arch/ia64/kvm/kvm-ia64.c.
  e790d9ef KVM: add kvm_arch_sched_in
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Opaque KVM structs are useful for prototypes in asm/kvm_host.h, to avoid
"'struct foo' declared inside parameter list" warnings (and consequent
breakage due to conflicting types).

Move them from individual files to a generic place in linux/kvm_types.h.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Introduce preempt notifiers for architecture specific code.
Advantage over creating a new notifier in every arch is slightly simpler
code and guaranteed call order with respect to kvm_sched_in.
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

fc95ca72 claims that there is no
functional change but this is not true as it calls get_order() (which
takes bytes) where it should have called order_base_2() and the kernel
stops on VM_BUG_ON().

This replaces get_order() with order_base_2() (round-up version of ilog2).
Suggested-by: NPaul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Add tracepoint to track hugepage invalidate. This help us
in debugging difficult to track bugs.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On ppc64 we support 4K hash pte with 64K page size. That requires
us to track the hash pte slot information on a per 4k basis. We do that
by storing the slot details in the second half of pte page. The pte bit
_PAGE_COMBO is used to indicate whether the second half need to be
looked while building real_pte. We need to use read memory barrier while
doing that so that load of hidx is not reordered w.r.t _PAGE_COMBO
check. On the store side we already do a lwsync in __hash_page_4K

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We would get wrong results in compiler recomputed old_pmd. Avoid
that by using ACCESS_ONCE

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As per ISA, for 4k base page size we compare 14..65 bits of VA specified
with the entry_VA in tlb. That implies we need to make sure we do a
tlbie with all the possible 4k va we used to access the 16MB hugepage.
With 64k base page size we compare 14..57 bits of VA. Hence we cannot
ignore the lower 24 bits of va while tlbie .We also cannot tlb
invalidate a 16MB entry with just one tlbie instruction because
we don't track which va was used to instantiate the tlb entry.

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault for
these pages.

We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.

Use _PAGE_COMBO to determine the page size with which we should
invalidate the hash table entries on unmap.

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault
for these pages.

We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.

Handle this correctly for 16M pages

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The segment identifier and segment size will remain the same in
the loop, So we can compute it outside. We also change the
hugepage_invalidate interface so that we can use it the later patch

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

With hugepages, we store the hpte valid information in the pte page
whose address is stored in the second half of the PMD. Use a
write barrier to make sure clearing pmd busy bit and updating
hpte valid info are ordered properly.

CC: <stable@vger.kernel.org>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There is an issue currently where NUMA information is used on powerpc
(and possibly ia64) before it has been read from the device-tree, which
leads to large slab consumption with CONFIG_SLUB and memoryless nodes.

NUMA powerpc non-boot CPU's cpu_to_node/cpu_to_mem is only accurate
after start_secondary(), similar to ia64, which is invoked via
smp_init().

Commit 6ee0578b ("workqueue: mark init_workqueues() as
early_initcall()") made init_workqueues() be invoked via
do_pre_smp_initcalls(), which is obviously before the secondary
processors are online.

Additionally, the following commits changed init_workqueues() to use
cpu_to_node to determine the node to use for kthread_create_on_node:

bce90380 ("workqueue: add wq_numa_tbl_len and
wq_numa_possible_cpumask[]")
f3f90ad4 ("workqueue: determine NUMA node of workers accourding to
the allowed cpumask")

Therefore, when init_workqueues() runs, it sees all CPUs as being on
Node 0. On LPARs or KVM guests where Node 0 is memoryless, this leads to
a high number of slab deactivations
(http://www.spinics.net/lists/linux-mm/msg67489.html).

Fix this by initializing the powerpc-specific CPU<->node/local memory
node mapping as early as possible, which on powerpc is
do_init_bootmem(). Currently that function initializes the mapping for
the boot CPU, but we extend it to setup the mapping for all possible
CPUs. Then, in smp_prepare_cpus(), we can correspondingly set the
per-cpu values for all possible CPUs. That ensures that before the
early_initcalls run (and really as early as possible), the per-cpu NUMA
mapping is accurate.

While testing memoryless nodes on PowerKVM guests with a fix to the
workqueue logic to use cpu_to_mem() instead of cpu_to_node(), with a
guest topology of:

available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus: 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
node 1 size: 16336 MB
node 1 free: 15329 MB
node distances:
node   0   1
  0:  10  40
  1:  40  10

the slab consumption decreases from

Slab:             932416 kB
SUnreclaim:       902336 kB

to

Slab:             395264 kB
SUnreclaim:       359424 kB

And we a corresponding increase in the slab efficiency from

slab                                   mem     objs    slabs
                                      used   active   active
------------------------------------------------------------
kmalloc-16384                       337 MB   11.28%  100.00%
task_struct                         288 MB    9.93%  100.00%

to

slab                                   mem     objs    slabs
                                      used   active   active
------------------------------------------------------------
kmalloc-16384                        37 MB  100.00%  100.00%
task_struct                          31 MB  100.00%  100.00%

Powerpc didn't support memoryless nodes until recently (64bb80d8
"powerpc/numa: Enable CONFIG_HAVE_MEMORYLESS_NODES" and 8c272261
"powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"). Those commits also
helped improve memory consumption with these kind of environments.
Signed-off-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Free memory allocated using kmem_cache_zalloc using kmem_cache_free
rather than kfree.

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@@
expression x,E,c;
@@

 x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
 ... when != x = E
     when != &x
?-kfree(x)
+kmem_cache_free(c,x)
// </smpl>
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

A buffer returned by H_VTERM_PARTNER_INFO contains device information
in big endian format, causing problems for little endian architectures.
This patch ensures that they are in cpu endian.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

xmon only soft disables interrupts. This seems like a bad idea - we
certainly don't want decrementer and PMU exceptions going off when
we are debugging something inside xmon.

This issue was uncovered when the hard lockup detector went off
inside xmon. To ensure we wont get a spurious hard lockup warning,
I also call touch_nmi_watchdog() when exiting xmon.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It appears that commits 7f06f21d ("powerpc/tm: Add checking to
treclaim/trechkpt") and e4e38121 ("KVM: PPC: Book3S HV: Add
transactional memory support") both added definitions of TEXASR_FS.
Remove one of them. At the same time, fix the alignment of the remaining
definition (should be tab-separated like the rest of the #defines).
Signed-off-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Function remove_ddw() could be called in of_reconfig_notifier and
we potentially remove the dynamic DMA window property, which invokes
of_reconfig_notifier again. Eventually, it leads to the deadlock as
following backtrace shows.

The patch fixes the above issue by deferring releasing the dynamic
DMA window property while releasing the device node.

=============================================
[ INFO: possible recursive locking detected ]
3.16.0+ #428 Tainted: G        W
---------------------------------------------
drmgr/2273 is trying to acquire lock:
 ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
 .__blocking_notifier_call_chain+0x40/0x78

but task is already holding lock:
 ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
 .__blocking_notifier_call_chain+0x40/0x78

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock((of_reconfig_chain).rwsem);
  lock((of_reconfig_chain).rwsem);
 *** DEADLOCK ***

 May be due to missing lock nesting notation

2 locks held by drmgr/2273:
 #0:  (sb_writers#4){.+.+.+}, at: [<c0000000001cbe70>] \
      .vfs_write+0xb0/0x1f8
 #1:  ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
      .__blocking_notifier_call_chain+0x40/0x78

stack backtrace:
CPU: 17 PID: 2273 Comm: drmgr Tainted: G        W     3.16.0+ #428
Call Trace:
[c0000000137e7000] [c000000000013d9c] .show_stack+0x88/0x148 (unreliable)
[c0000000137e70b0] [c00000000083cd34] .dump_stack+0x7c/0x9c
[c0000000137e7130] [c0000000000b8afc] .__lock_acquire+0x128c/0x1c68
[c0000000137e7280] [c0000000000b9a4c] .lock_acquire+0xe8/0x104
[c0000000137e7350] [c00000000083588c] .down_read+0x4c/0x90
[c0000000137e73e0] [c000000000091890] .__blocking_notifier_call_chain+0x40/0x78
[c0000000137e7490] [c000000000091900] .blocking_notifier_call_chain+0x38/0x48
[c0000000137e7520] [c000000000682a28] .of_reconfig_notify+0x34/0x5c
[c0000000137e75b0] [c000000000682a9c] .of_property_notify+0x4c/0x54
[c0000000137e7650] [c000000000682bf0] .of_remove_property+0x30/0xd4
[c0000000137e76f0] [c000000000052a44] .remove_ddw+0x144/0x168
[c0000000137e7790] [c000000000053204] .iommu_reconfig_notifier+0x30/0xe0
[c0000000137e7820] [c00000000009137c] .notifier_call_chain+0x6c/0xb4
[c0000000137e78c0] [c0000000000918ac] .__blocking_notifier_call_chain+0x5c/0x78
[c0000000137e7970] [c000000000091900] .blocking_notifier_call_chain+0x38/0x48
[c0000000137e7a00] [c000000000682a28] .of_reconfig_notify+0x34/0x5c
[c0000000137e7a90] [c000000000682e14] .of_detach_node+0x44/0x1fc
[c0000000137e7b40] [c0000000000518e4] .ofdt_write+0x3ac/0x688
[c0000000137e7c20] [c000000000238430] .proc_reg_write+0xb8/0xd4
[c0000000137e7cd0] [c0000000001cbeac] .vfs_write+0xec/0x1f8
[c0000000137e7d70] [c0000000001cc3b0] .SyS_write+0x58/0xa0
[c0000000137e7e30] [c00000000000a064] syscall_exit+0x0/0x98

Cc: stable@vger.kernel.org
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>