This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert.  New LPA translation functions have been added as well.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Translating between ethtool advertisement settings and MII
advertisements are common operations for ethernet drivers.  This patch
adds a set of helper functions that implements the conversion.  The
patch then modifies a couple of the drivers to use the new functions.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are references to this PHY chip in the generic mii.h header, so removing them.
Re-jiggle the changed comments, in response to points raised by Ben Hutchings.
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whitespace changes - spaces converted to tabs after each define name and value
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes to code to use some of the preprocessor
definitions from mii.h over its homegrown equivalents.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@conan.davemloft.net>

This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These 4 drivers have identical full duplex flow control resolution
functions.  This patch changes them all to use one common function.

The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.

The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Matvejchikov Ilya.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They shouldn't be using 'u32' et al in structures which are used for
communication with userspace. Switch to the proper types (__u32 etc).
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

A new driver bnx2 for Broadcom bcm5706 is available.

The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h

Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!