Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 08 3月, 2011 2 次提交
  3. 26 2月, 2011 1 次提交
  5. 22 12月, 2010 2 次提交
  7. 21 12月, 2010 1 次提交
  9. 10 12月, 2010 1 次提交
  11. 09 10月, 2010 2 次提交
    • P
      OMAP: control: move plat-omap/control.h to mach-omap2/control.h · 4814ced5
      由 Paul Walmsley 提交于 
      Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap.  This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.

In response, move the SCM headers into mach-omap2/.

As part of this, remove the direct SCM access from the OMAP UDC
driver.  It was clearly broken.  The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
      4814ced5
    • P
      OMAP2420: clock: add MCBSP_CLKS node and clkdev aliases · 1bccb345
      由 Paul Walmsley 提交于 
      Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSP 1 and 2.  Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      1bccb345
  13. 28 9月, 2010 1 次提交
  15. 03 9月, 2010 1 次提交
  17. 21 5月, 2010 2 次提交
    • P
      OMAP2+ clock: remove DEFAULT_RATE clksel_rate flag · d74b4949
      由 Paul Walmsley 提交于 
      The DEFAULT_RATE clksel_rate flag is essentially useless.  It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.

Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person.  The
parent changing code is rarely used.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      d74b4949
    • P
      OMAP2 PRCM: convert OMAP2 PRCM macros to the _SHIFT/_MASK suffixes · f38ca10a
      由 Paul Walmsley 提交于 
      Fix all of the remaining OMAP2 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them.  This makes the use
of these macros consistent.  It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
      f38ca10a
  19. 03 5月, 2010 1 次提交
  21. 12 3月, 2010 1 次提交
  23. 25 2月, 2010 8 次提交
    • P
      OMAP clock: drop RATE_FIXED clock flag · 51c19541
      由 Paul Walmsley 提交于 
      The RATE_FIXED clock flag is pointless.  In the OMAP1 clock code, it
simply causes the omap1_clk_round_rate() function to return the
current rate of the clock.  omap1_clk_round_rate(), however, should
never be called for a fixed-rate clock, since none of these clocks
have a .round_rate function pointer set in their struct clk records.
Similarly, in the OMAP2+ clock code, the RATE_FIXED flag just causes
the clock code to emit a warning if the OMAP clock maintainer was
foolish enough to add a .round_rate function pointer to a fixed-rate
clock.  "Doctor, it hurts when I pretend that a fixed-rate clock is
rate-changeable."  "Then don't pretend that a fixed-rate clock is
rate-changeable."  It has no functional value.  This patch drops the
RATE_FIXED clock flag, removing it from all clocks that are so marked.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      51c19541
    • P
      OMAP2 clock: drop DELAYED_APP clock flag · 8c34974a
      由 Paul Walmsley 提交于 
      All of the clocks that are marked with DELAYED_APP are changed as part
of the virt_prcm_set OPP virtual clock.  On 24xx, these clocks all
need to be changed as part of a group to keep the clock tree
functional - hence the need for the VALID_CONFIG bit, which is not
present on later OMAPs.  These clocks should not be rate-changed
independently.  So prevent these clocks from being changed
independently by dropping their .round_rate and .set_rate function
pointers.  It then turns out that the DELAYED_APP clock flag is no
longer useful, so drop it and the associated code and renumber the
clock flags.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      8c34974a
    • P
      OMAP2 clock: split OMAP2420, OMAP2430 clock data into their own files · 81b34fbe
      由 Paul Walmsley 提交于 
      In preparation for multi-OMAP2 kernels, split
mach-omap2/clock2xxx_data.c into mach-omap2/clock2420_data.c and
mach-omap2/clock2430_data.c.  2430 uses a different device space
physical memory layout than past or future OMAPs, and we use a
different virtual memory layout as well, which causes trouble for
architecture-level code/data that tries to support both.  We tried
using offsets from the virtual base last year, but those patches never
made it upstream; so after some discussion with Tony about the best
all-around approach, we'll just grit our teeth and duplicate the
structures.  The maintenance advantages of a single kernel config that
can compile and boot on OMAP2, 3, and 4 platforms are simply too
compelling.

This approach does have some nice benefits beyond multi-OMAP 2 kernel
support.  The runtime size of OMAP2420-specific and OMAP2430-specific
kernels is smaller, since unused clocks for the other OMAP2 chip will
no longer be compiled in.  (At some point we will mark the clock data
__initdata and allocate it during registration, which will eliminate
the runtime memory advantage.)  It also makes the clock trees slightly
easier to read, since 2420-specific and 2430-specific clocks are no
longer mixed together.

This patch also splits 2430-specific clock code into its own file,
mach-omap2/clock2430.c, which is only compiled in for 2430 builds -
mostly for organizational clarity.

While here, fix a bug in the OMAP2430 clock tree: "emul_ck" was
incorrectly marked as being 2420-only, when actually it is present on
both OMAP2420 and OMAP2430.

Thanks to Tony for some good discussions about how to approach this
problem.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      81b34fbe
    • P
      OMAP clock: drop .id field; ensure each clock has a unique name · b92c170d
      由 Paul Walmsley 提交于 
      After the clkdev conversion, the struct clk.id field became
superfluous, so, drop it.  Bring the clock names closer to the TRMs
and ensure they are unique for debugfs.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      b92c170d
    • P
      OMAP2 clock: drop CONFIG_PARTICIPANT clock flag · 1a337717
      由 Paul Walmsley 提交于 
      It turns out that the only purpose of the CONFIG_PARTICIPANT clock
flag is to prevent omap2_clk_set_rate() and omap2_clk_set_parent()
from being executed on clocks with that flag set.  The rate-changing
component can be more directly accomplished by dropping the .set_rate
and .round_rate function pointers from those CONFIG_PARTICIPANT struct
clks.  As far as the parent-changing component is concerned, it turns
out that none of the CONFIG_PARTICIPANT clocks have multiple parent
choices, so all that is necessary is for omap2_clk_set_parent() to
bail out early if the new parent is equal to the old parent.
Implement this change and get rid of the flag, which has always had a
confusing name (it appears to be a Kconfig option, falsely).
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      1a337717
    • P
      OMAP2xxx clock: drop DELAYED_APP flag from non-clksel clocks · 17d09273
      由 Paul Walmsley 提交于 
      The DELAYED_APP flag is effective only with clksel clocks, so drop it from
clocks that are not rate-changeable or that use non-clksel rate changing code
(e.g., virt_prcm_set).
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      17d09273
    • P
      OMAP2xxx clock: GFX functional clock rates are not independently changeable · 94297784
      由 Paul Walmsley 提交于 
      According to the OMAP242x TRM Rev X Figure 5-15 "Clock Output Control
- Functional Clocks 2", the GFX functional clocks should be marked
both DELAYED_APP and CONFIG_PARTICIPANT, meaning that their rates must
be reprogrammed as part of a larger OPP set change.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      94297784
    • P
      OMAP2/3/4 clock: fix DPLL multiplier value errors; also copyrights, includes, documentation · 93340a22
      由 Paul Walmsley 提交于 
      The maximum DPLL multiplier (M) values for OMAP2xxx and OMAP3xxx are
one increment higher than they should be.  See for example the
OMAP242x TRM Rev X Section 5.10.6 "Clock Generator Registers" and the
OMAP36xx TRM Rev C Table 3-202 "CM_CLKSEL1_PLL".  Programming a 0 into
the DPLL's M register bitfield is valid for OMAP2/3 and indicates that
the DPLL should enter MN-bypass mode.  Also, increase the minimum
multiplier (M) value for the DPLL rate rounding code from 1 to 2, to
ensure that it does not inadvertently put the DPLL into bypass.

Note that the register documentation in the OMAP2xxx and OMAP3xxx TRMs
does not make clear that the actual DPLL divider value (the "N") is
the content of the appropriate register bitfield for the N value,
_plus one_.  (In other words, an N register bitfield of 0 indicates a
DPLL divider value of 1.)  This is only clearly documented in the
OMAP4430 TRM, in, for example, OMAP4430 TRM Rev A Table 3-1167
"CM_CLKSEL_DPLL_USB".

While here, update copyrights, add kerneldoc for struct dpll_data,
drop the unused struct dpll_data.max_tolerance field, remove some
unnecessary #includes in DPLL-related code, and replace the #include
of <linux/module.h> with <linux/list.h>, which is what was really
needed.  The OMAP4 clock autogenerator script has been updated
accordingly.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
      93340a22
  25. 30 1月, 2010 1 次提交
    • P
      OMAP2/3/4 clock: rename and clean the omap2_clk_init() functions · e80a9729
      由 Paul Walmsley 提交于 
      Rename the omap2_clk_init() in the OMAP2, 3, and 4 clock code to be
omap2xxx_clk_init(), omap3xxx_clk_init(), etc.  Remove all traces of
the (commented) old virt_prcm_set code from omap3xxx_clk_init() and
omap4xxx_clk_init(), since this will be handled with the OPP code that
is cooking in the PM branch.

After this patch, there should be very little else in the clock code
that blocks a multi-OMAP 2+3 kernel.  (OMAP2420+OMAP2430 still has some
outstanding issues that need to be resolved; this is pending on some
additions to the hwmod data.)
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      e80a9729
  27. 29 1月, 2010 1 次提交
    • P
      OMAP2xxx clock: move sys_clk code into mach-omap2/clkt2xxx_sys.c · 44da0a51
      由 Paul Walmsley 提交于 
      Move the sys_clk clock functions from clock2xxx.c to
mach-omap2/clkt2xxx_sys.c.  This is intended to make the clock code
easier to understand, since all of the functions needed to manage the
sys_clk are now located in their own file, rather than being mixed
with other, unrelated functions.

Clock debugging is also now more finely-grained, since the DEBUG
macro can now be defined for the sys_clk clock alone.  This
should reduce unnecessary console noise when debugging.

Also, if at some future point the mach-omap2/ directory is split into
OMAP2/3/4 variants, this clkt file can be placed in the mach-omap2xxx/
directory, rather than shared with other chip types that don't use
this clock type.

Thanks to Alexander Shishkin <virtuoso@slind.org> for his comments to
improve the patch description.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Alexander Shishkin <virtuoso@slind.org>
      44da0a51
  29. 27 1月, 2010 1 次提交
  31. 12 12月, 2009 2 次提交
    • P
      OMAP2 clock: convert clock24xx.h to clock2xxx_data.c, opp2xxx* · d8a94458
      由 Paul Walmsley 提交于 
      The OMAP2 clock code currently #includes a large .h file full of static
data structures.  Instead, define the data in a .c file.

Russell King <linux@arm.linux.org.uk> proposed this new arrangement:

    http://marc.info/?l=linux-omap&m=125967425908895&w=2

This patch also deals with most of the flagrant checkpatch violations.

While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device.  This should save some memory.  In the long run,
these prcm_config tables should be replaced with OPP code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
      d8a94458
    • P
      OMAP2 clock: APLL code shouldn't rely on static clocks in its local namespace · 06b16939
      由 Paul Walmsley 提交于 
      Similar to the previous patch, the APLL code relied on the presence of the
static struct clks in its own namespace.  The APLL code didn't use them for
validation, however - it adjusted its own internal state depending on
the struct clk * that called it.  Now that static struct clks are
leaving the clock24xx.c namespace, use a more durable method: split the
omap2_clk_fixed_enable() function into omap2_clk_apll96_enable() and
omap2_clk_apll54_enable().  They still share a disable function.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      06b16939
  33. 25 7月, 2009 1 次提交
    • P
      OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST register · 3dc21975
      由 Paul Walmsley 提交于 
      OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1].  Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.

...

1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
   (Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      3dc21975
  35. 26 5月, 2009 4 次提交
  37. 24 4月, 2009 1 次提交
    • P
      OMAP2/3 GPTIMER: allow system tick GPTIMER to be changed in board-*.c files · f248076c
      由 Paul Walmsley 提交于 
      Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12.  Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management.  GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management.  GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator.  But on HS devices, it
may not be available for Linux use.

It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below.  Modify board-omap3beagle.c to use GPTIMER12.

This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.

Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.

Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
      f248076c
  39. 20 2月, 2009 1 次提交
    • R
      [ARM] omap: add support for bypassing DPLLs · c0bf3132
      由 Russell King 提交于 
      This roughly corresponds with OMAP commits: 7d06c48, 3241b19,
88b5d9b, 18a5500, 9c909ac, 5c6497b, 8b1f0bd, 2ac1da8.

For both OMAP2 and OMAP3, we note the reference and bypass clocks in
the DPLL data structure.  Whenever we modify the DPLL rate, we first
ensure that both the reference and bypass clocks are enabled.  Then,
we decide whether to use the reference and DPLL, or the bypass clock
if the desired rate is identical to the bypass rate, and program the
DPLL appropriately.  Finally, we update the clock's parent, and then
disable the unused clocks.

This keeps the parents correctly balanced, and more importantly ensures
that the bypass clock is running whenever we reprogram the DPLL.  This
is especially important because the procedure for reprogramming the DPLL
involves switching to the bypass clock.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      c0bf3132
  41. 14 2月, 2009 1 次提交
    • R
      [ARM] omap: arrange for clock recalc methods to return the rate · 8b9dbc16
      由 Russell King 提交于 
      linux-omap source commit 33d000c99ee393fe2042f93e8422f94976d276ce
introduces a way to "dry run" clock changes before they're committed.
However, this involves putting logic to handle this into each and
every recalc function, and unfortunately due to the caching, led to
some bugs.

Solve both of issues by making the recalc methods always return the
clock rate for the clock, which the caller decides what to do with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      8b9dbc16
  43. 09 2月, 2009 4 次提交