For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.

Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: NBrian Walsh <brian@walsh.ws>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.

For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.

e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.

Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: NSteve Shih <sshih@cisco.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While testing an OpenStack configuration using VXLANs I saw the following
call trace:

 RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
 RSP: 0018:ffff88103867bc50  EFLAGS: 00010286
 RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
 RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
 RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
 R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
 R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
 FS:  0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
 Stack:
  ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
  ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
  ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
 Call Trace:
  [<ffffffff81576515>] ? skb_checksum+0x35/0x50
  [<ffffffff815733c0>] ? skb_push+0x40/0x40
  [<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
  [<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
  [<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
  [<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
  [<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
  [<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
  [<ffffffff815899d0>] net_rx_action+0x160/0x380
  [<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
  [<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
  [<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
  [<ffffffff8109a400>] ? sort_range+0x30/0x30
  [<ffffffff81096da8>] kthread+0xd8/0xf0
  [<ffffffff81693c82>] ret_from_fork+0x22/0x40
  [<ffffffff81096cd0>] ? kthread_park+0x60/0x60

The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel.  I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.

To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev.  This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated.  In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.

Fixes: 63058308 ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sunrpc is using SOCKWQ_ASYNC_NOSPACE without setting SOCK_FASYNC,
so the recent optimizations done in sk_set_bit() and sk_clear_bit()
broke it.

There is still the risk that a subsequent sock_fasync() call
would clear SOCK_FASYNC, but sunrpc does not use this yet.

Fixes: 9317bb69 ("net: SOCKWQ_ASYNC_NOSPACE optimizations")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NJiri Pirko <jiri@resnulli.us>
Reported-by: NHuang, Ying <ying.huang@intel.com>
Tested-by: NJiri Pirko <jiri@resnulli.us>
Tested-by: NHuang, Ying <ying.huang@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an ACTIVATE or data packet is received in a link in state
ESTABLISHING, the link does not immediately change state to
ESTABLISHED, but does instead return a LINK_UP event to the caller,
which will execute the state change in a different lock context.

This non-atomic approach incurs a low risk that we may have two
LINK_UP events pending simultaneously for the same link, resulting
in the final part of the setup procedure being executed twice. The
only potential harm caused by this it that we may see two LINK_UP
events issued to subsribers of the topology server, something that
may cause confusion.

This commit eliminates this risk by checking if the link is already
up before proceeding with the second half of the setup.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not include attribute IFLA_GRE_TOS.
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a netns leak.

Fixes: 93edb8c7 ("gtp: reload GTPv1 header after pskb_may_pull()")
Reported-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Some more work for 4.7, notably:
 * completion and fixups of nla_put_64_64bit() work
 * remove a/b/g/n from wext nickname to avoid confusion
   with 11ac (which wouldn't even fit fully there due to
   string length restrictions)

along with some other minor changes/cleanups.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.

In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.

To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The devlist_mtx mutex was removed about two years ago, in favour of just
using RTNL/RCU protection. Remove the comment still referencing it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows finding vendor IE from a specific vendor.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack.  Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Yuval Mintz says:

====================
qed*: Add SR-IOV support

This patch adds SR-IOV support to qed/qede drivers, adding a new PCI
device ID for a VF that is shared between all the various PFs that
support IOV.

This is quite a massive series - the first 7 parts of the series add
the infrastructure of supporting vfs in qed - mainly adding support in a
HW-based vf<->pf channel, as well as diverging all existing configuration
flows based on the pf/vf decision. I.e., while PF-originated requests
head directly to HW/FW, the VF requests first have to traverse to the PF
which will perform the configuration.

The 8th patch is the one that adds the support for the VF device in qede.

The remaining 6 patches each adds some user-based API support related to
VFs that can be used over the PF - forcing mac/vlan, changing speed, etc.

Dave,

Sorry in advance for the length of the series. Most of the bulk here is in
the infrastructure patches that have to go together [or at least, it makes
little sense to try splitting them up].

Please consider applying this to `net-next'.

Thanks,
Yuval

Changes from previous revision:
------------------------------
 - V2 - Replace aligned_u64 with regular u64; This was possible as the
        shared structures [between PF and VF] were already sufficiently
        padded as-is in the API, making this redundant.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.

While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.

 1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
    <vid> and tags all outgoing traffic sent by VF with <vid>.
 2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.

This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.

It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.

This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]

Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds sufficient changes to allow VFs l2-configuration flows to work.

While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.

It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.

This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.

The messages themselves are TLV-based - allowing easier backward/forward
compatibility.

This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.

It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.

This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Samuel Ortiz says:

====================
NFC 4.7 pull request

This is the first NFC pull request for 4.7. With this one we
mainly have:

- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
  microcontroller as the pn533, but it talks to the host through i2c
  instead of USB. By separating the pn533 driver into core and PHY
  parts, we can not add the i2c layer and support the pn532 chipset.

- Support for NCI's loopback mode. This is a testing mode where each
  packet received by the NFCC is sent back to the DH, allowing the
  host to test that the controller can receive and send data.

- A few ACPI related fixes for the STMicro drivers, in order to match
  the device tree naming scheme.

- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 CQE compression

Introducing ConnectX-4 CQE (Completion Queue Entry) compression feature
for mlx5 etherent driver.

CQE Compressing reduces PCI overhead by coalescing and compressing multiple CQEs into a
single merged CQE.  Successful compressing improves message rate especially for small packet
traffic.

CQE Compressing in details:

Instead of writing full CQEs to memory, multiple almost identical CQEs are merged and compressed.
Information that is shared between the CQEs is written once, regardless of the number of
compressed CQEs.  In addition, only the unique information (small amount of bytes compared to
full CQE size) is written per CQE.

CQE Compression Block:

This block contains multiple compressed CQEs.  CQE Compression Block contains a single copy
of CQEs properties which are shared between all the compressed CQEs (called Title, see below)
and multiple mini CQEs (CQEs in compressed form).

Title:

The Title holds information which is shared between all the compressed CQEs in the CQE Compression
Block.  In each Compression Block there is only a single Title regardless of the number
of compressed CQEs.

Mini CQE:

A CQE in compressed form that holds some data needed to extract a single full CQE, for example
8 Bytes instead of 64 Bytes.
The shared information between all compressed CQEs, which belong to the same CQE Compression
Block called Title, is written once, and only the unique information in each compressed
CQE, for example 8 bytes, is written per compressed CQE, called mini CQE.

Since CQE Compression can add overhead to the software (CPU),
it will be only enabled on "weak/slow" PCI slots, where it can actually help.

Applied on top: c047c3b1 ('netfilter: conntrack: remove uninitialized shadow variable')
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We turn the feature ON, only for servers with PCI BW < MAX LINK BW, as it
helps reducing PCI pressure on weak PCI slots, but it adds some software
overhead.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the MPWQE/Striding RQ default configuration dynamic and not
statically set at compile time.  Now at driver load we set
stride size and num strides dynamically.

By default we use same values as before, but when CQE compression
is enabled, we set larger stride size to benefit from CQE
compression for larger packets.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ.  By default
is disabled for now and will be enabled later on.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
More enabler patches for DSA probing

The complete set of patches for the reworked DSA probing is too big to
post as once. These subset contains some enablers which are easy to
review.

Eventually, the Marvell driver will instantiate its own internal MDIO
bus, rather than have the framework do it, thus allows devices on the
bus to be listed in the device tree. Initialize the main mutex as soon
as it is created, to avoid lifetime issues with the mdio bus.

A previous patch renamed all the DSA probe functions to make room for
a true device probe. However the recent merging of all the Marvell
switch drivers resulted in mv88e6xxx going back to the old probe
name. Rename it again, so we can have a driver probe function.

Add minimum support for the Marvell switch driver to probe as an MDIO
device, as well as an DSA driver. Later patches will then register
this device with the new DSA core framework.

Move the GPIO reset code out of the DSA code. Different drivers may
need different reset mechanisms, e.g. via a reset controller for
memory mapped devices. Don't clutter up the core with this. Let each
driver implement what it needs.

master_dev is no longer needed in the switch drivers, since they have
access to a device pointer from the probe function. Remove it.

Let the switch parse the eeprom length from its one device tree
node. This is required with the new binding when the central DSA
platform device no longer exists.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A switch can export an attached EEPROM using the standard ethtool API.
However the switch itself cannot determine the size of the EEPROM, and
multiple sizes are allowed. Thus a device tree property is supported
to indicate the length of the EEPROM. Parse this property during
device probe, and implement a callback function to retrieve it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>