Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 30 4月, 2013 7 次提交
  3. 29 4月, 2013 7 次提交
  5. 27 4月, 2013 14 次提交
  7. 26 4月, 2013 8 次提交
  9. 25 4月, 2013 4 次提交
    • V
      net: fix address check in rtnl_fdb_del · 37fe0660
      由 Vlad Yasevich 提交于 
      Commit 6681712d
	vxlan: generalize forwarding tables

relaxed the address checks in rtnl_fdb_del() to use is_zero_ether_addr().
This allows users to add multicast addresses using the fdb API.  However,
the check in rtnl_fdb_del() still uses a more strict
is_valid_ether_addr() which rejects multicast addresses.  Thus it
is possible to add an fdb that can not be later removed.
Relax the check in rtnl_fdb_del() as well.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      37fe0660
    • S
      net/cpsw: fix irq_disable() with threaded interrupts · a11fbba9
      由 Sebastian Siewior 提交于 
      During high throughput it is likely that we receive both: an RX and TX
interrupt. The normal behaviour is that once we enter the ISR the
interrupts are disabled in the IRQ chip and so the ISR is invoked only
once and the interrupt line is disabled once. It will be re-enabled
after napi completes.
With threaded interrupts on the other hand the interrupt the interrupt
is disabled immediately and the ISR is marked for "later". By having TX
and RX interrupt marked pending we invoke them both and disable the
interrupt line twice. The napi callback is still executed once and so
after it completes we remain with interrupts disabled.

The initial patch simply removed the cpsw_{enable|disable}_irq() calls
and it worked well on my AM335X ES1.0 (beagle bone). On ES2.0 (beagle
bone black) it caused an never ending interrupt (even after the mask via
cpsw_intr_disable()) according to Mugunthan V N. Since I don't have the
ES2.0 and no idea what is going on this patch tracks the state of the
irq_disable() call and execute it only when not yet done.
The book keeping is done on the first struct since with dual_emac we can
have two of those and only one interrupt line.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a11fbba9
    • S
      net/cpsw: optimize the for_each_slave_macro() · 6e6ceaed
      由 Sebastian Siewior 提交于 
      text    data     bss     dec     hex filename
15530      92       4   15626    3d0a cpsw.o.before
15478      92       4   15574    3cd6 cpsw.o.after

52 bytes smaller, 13 for each invocation.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6e6ceaed
    • S
      net/cpsw: make sure modules remove does not leak any ressources · d1bd9acf
      由 Sebastian Siewior 提交于 
      This driver does not clean up properly after leaving. Here is a list:
- Use unregister_netdev(). free_netdev() is good but not enough
- Use the above also on the other ndev in case of dual mac
- Free data.slave_data. The name of the strucre makes it look like
  it is platform_data but it is not. It is just a trick!
- Free all irqs. Again: freeing one irq is good start, but freeing all
  of them is better.

With this rmmod & modprobe of cpsw seems to work. The remaining issue
is:
|WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0x9c/0xd4()
|sysfs: cannot create duplicate filename '/devices/ocp.2/4a100000.ethernet/4a101000.mdio'
|WARNING: at lib/kobject.c:196 kobject_add_internal+0x1a4/0x1c8()

comming from of_platform_populate() and I am not sure that this belongs
here.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d1bd9acf