bonding / alternating candidates need to be secured by rcu locks
as well. This patch therefore converts the bonding list
from a plain pointer list to a rcu securable lists and references
the bonding candidates.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NSven Eckelmann <sven@narfation.org>

Linux 2.6.21 defines different macros for __attribute__ which are also
used inside batman-adv. The next version of checkpatch.pl warns about
the usage of __attribute__((packed))).

Linux 2.6.33 defines an extra macro __always_unused which is used to
assist source code analyzers and can be used to removed the last
existing __attribute__ inside the source code.
Signed-off-by: NSven Eckelmann <sven@narfation.org>

B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Via the /sys filesystem you can change the gateway mode of a node using
gw_mode. Adjustments to it can be done using gw_bandwidth for server
mode and gw_sel_class for client mode.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When having a mixed topology of both very mobile and rather static
nodes, you are usually best advised to set the originator interval on
all nodes to a level best suited for the most mobile node.

However, if most of the nodes are rather static, this can create a lot
of undesired overhead as a trade-off then. If setting the interval too
low on the static nodes, a mobile node might be chosen as a router for
too long, not switching away from it fast enough because of its
mobility and the low frequency of ogms of static nodes.

Exposing the hop_penalty is especially useful for the stated scenario: A
static node can keep the default originator interval, a mobile node can
select a quicker one resulting in faster route updates towards this
mobile node. Additionally, such a mobile node could select a higher hop
penalty (or even set it to 255 to disable acting as a router for other
nodes) to make it less desirable, letting other nodes avoid selecting
this mobile node as a router.
Signed-off-by: NLinus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Both sysfs entries and variable names shall be as descriptive as
possible while not exceeding a certain length. This patch renames
bat_priv atomics to be equally descriptive with their according sysfs
entries.

Unifying sysfs and bat_priv atomic names also makes it easier to find
each others pendant.

The reduced ("type"-)information which was previously indicated with a
_enabled for booleans got substituted by a comment in bat_priv.

This patch has also been done in regards for the future BAT_ATTR_*
macros (they only need one name argument instead of a file and variable
name).
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:

node1  <-- LAN  -->  node2
   |                   |
 wifi  <-- mesh -->  wifi

Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.

This patch adds the functionality to detect other batman-adv nodes
connected to the LAN and select a 'gateway' to talk to the
non-batman-adv devices on this LAN. All traffic from and to the mesh
will be handled by this gateway to avoid the loop. OGMs received via
the soft-interface are interpreted as 'port announcements' to locate
potential batman-adv nodes. The patch can also deal with vlans on
top of batX and offers a list of LAN neighbors via debugfs.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since all *printf() methods in the kernel understand '%pM' modifier the
conversion to the string is useless beforehand.

Additionally this patch decreases batman_if structure by 20 bytes.
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

get_batman_if_by_netdev and get_active_batman_if may leak data from the
rcu protected list of interfaces. The rcu protected list of all gateway
nodes leaks the actual data outside the read-side critical area. This is
not valid as we may free the data using a call_rcu created callback
after we unlock using rcu_read_unlock. A workaround is to provide a
reference count to be sure that the memory isn't freed to early.

It is currently only to implement the already existing functionality and
doesn't provide the full tracking of all usage cases.

Additionally, we must hardif_hold inside the
rcu_read_lock()..rcu_read_unlock() before we attach to the structure
which "leaks" it. When another function now removed it from its usage
context (primary_if, usage on stack, ...) then we must hardif_put it. If
it is decremented to zero then we can issue the call_rcu to the freeing
function. So "put" is not allowed inside an rcu_read_lock.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It is recommended [1] to use synchronize_rcu to simplify the code -
especially when otherwise extra locking is needed to protect other code
from picking stale elements. It also protects us for emitting to many
callbacks which may results in OOM conditions.

The only reason not to use it, would be in performance critical sections
or when we are not allowed to block.

[1] Documentation/RCU/checklist.txt
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

checkpatch now detects the start of a comment and warns about usage of
multiple spaces at the beginning of a line. We have to replace the '   '
in multiple lines comments by ' * ' to fix it.

Checkpatch also wants a comment after a definition of a spinlock_t which
describes what it protects. It is currently not possible to add it
before the actual struct which includes the spinlock.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

gw_list_lock, gw_list and curr_gw are currently unused members of struct
bat_priv. They will be readded when gateway support is really
implemented.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

batman_if has the name of the net_dev as extra string in its own
structure, but also holds a reference to the actual net_device structure
which always has the current name of the device. This makes it
unneccessary and also more complex because we must update the name in
situations when we receive a NETDEV_CHANGENAME event.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes all remaining global variables and includes the
necessary bits into the bat_priv structure. It is the last
remaining piece to allow multiple concurrent mesh clouds on the
same device.
A few global variables have been rendered obsolete during the process
and have been removed entirely.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch replaces the static bat0 interface with a dynamic/abstracted
approach. It is now possible to create multiple batX interfaces by
assigning hard interfaces to them. Each batX interface acts as an
independent mesh network. A soft interface is removed once no hard
interface references it any longer.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All originator messages are send through aggregation buffers. Those
buffers can directly be allocated as skb to reduce the cost of
allocation an extra buffer and copying them to a new allocated skb
directly before it gets send.

Now only the skb must be cloned in case of send_packet_to_if as it gets
called by send_packet for each interface. Non-primary ogms must not
cloned at all because they will only send once and the forward_packet
structure is freed by send_outstanding_bat_packet afterwards.
Reported-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Batman-adv globally registered the batman-adv packet type and installed
a hook to batman_skb_recv(). Each interface receiving a packet with that
type would end up in this function which then had to loop through all
batman-adv internal interface structures to find the its meta data. The
more interfaces a system had the longer the loops might take. Each and
every packet goes through this function making it a performance critical
loop.

This patch installs the hook for each activated interface. The called
batman_skb_recv() can distinguish these calls, therefore avoiding the
loop through the interface structures.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements a simple layer2 fragmentation to allow traffic
exchange over network interfaces with a MTU smaller than 1500 bytes. The
fragmentation splits the big packets into two parts and marks the frames
accordingly. The receiving end buffers the packets to reassemble the
orignal packet before passing it to the higher layers. This feature
makes it necessary to modify the batman-adv encapsulation for unicast
packets by adding a sequence number, flags and the originator address.
This modifcation is part of a seperate packet type for fragemented
packets to keep the original overhead as low as possible. This patch
enables the feature by default to ensure the data traffic can travel
through the network. But it also prints a warning to notify the user
about the performance implications.

Note: Fragmentation should be avoided at all costs since it has a
dramatic impact on the performance, especially when it comes wifi
networks. Instead of a single packet, 2 packets have to be sent! Not
only valuable airtime is wasted but also packetloss decreases the
throughput. A link with 50% packetloss and fragmentation enabled is
pretty much unusable.
Signed-off-by: NAndreas Langer <an.langer@gmx.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

to support multiple mesh devices later, we need to move global variables
like the queues into corresponding private structs bat_priv of the soft
devices.

Note that this patch still has a lot of FIXMEs and depends on the global
soft_device variable. This should be resolved later, e.g. by referencing
the parent soft device in batman_if.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If a batman icmp packet had to be routed over a secondary interface
at the first hop, the mac address of that secondary interface would
be written in the 'orig' field of the icmp packet. A node which is
more than one hop away is not aware of the mac address because
secondary interfaces are not flooded through the whole mesh and
therefore can't send a reply.
This patch always sends the mac address of the primary interface
in the 'orig' field of the icmp packet.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All routing debug messages are saved in a ring buffer that can be
read via the debugfs file "log".
Note that CONFIG_BATMAN_ADV_DEBUG must be activated to have the
debug logs compiled in.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We include different header files indirectly to the same source file.
This creates weird compiler errors from time to time. Include guards
should prefend that functions/variables/... gets redefined by itself.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The standard layer 3 ping utility can use the record route (RR) option
of IP to collect route data for sent ping messages (ping -R). This
patch introduces comparable functionality for batman-adv ICMP messages.

The patch adds a second batman ICMP packet format (icmp_packet_rr) such
that up to 17 MAC addresses can be recorded (sufficient for up to 8
hops per direction). When no RR is wanted, the old icmp_packet without
the RR overhead can be sent.
Signed-off-by: NDaniel Seither <post@tiwoc.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch introduces bonding functionality to batman-advanced, targeted
for the 0.3 release. As we are able to route the payload traffic as we
want, we may use multiple interfaces on multihomed hosts to transfer data
to achieve higher bandwidth. This can be considered as "light Multi Path
Routing" for single hop connections.

To detect which interfaces of a peer node belong to the same host, a
new flag PRIMARIES_FIRST_HOP is introduced. This flag is set on the first hop
of OGMs of the primary (first) interface, which is broadcasted on all
interfaces. When receiving such an OGM, we can learn which interfaces
belong to the same host (by assigning them to the primary originator).

Bonding works by sending packets in a round-robin fashion to the available
interfaces of a neighbor host, if multiple interfaces are available. The
neighbor interfaces should be almost equally good to reach.

To avoid interferences (i.e. sending on the same channel), only neighbor
interfaces with different mac addresses and different outgoing interfaces
are considered as candidates.

Bonding is deactivated by default, and can be activated by

echo 1 > /sys/class/net/bat0/mesh/bonding

for each individual node.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes the sequence number range from 8 or 16 bit to 32 bit.
This should avoid problems with the sequence number sliding window algorithm
which we had seen in the past for broadcast floods or malicious packet
injections. We can not assure 100% security with this patch, but it is quite
an improvement over the old 16 bit sequence numbers:

 * expected window size can be increased (4096 -> 65536)
 * 64k packets in the right order would now be needed to cause a loop,
   which seems practically impossible.

Furthermore, a TTL field has been added to the broadcast packet type, just to
make sure.

These changes required to increase the compatibility level once again.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
[sven.eckelmann@gmx.de: Change atomic64_* back to atomic_*, Rework on
top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

batctl uses /dev/batman-adv to send special batman-adv icmp packets to
other nodes in the mesh. To get it working with multiple batX devices we
must ensure that every mesh device can have their own socket which is
used to inject those packets in exactly one mesh.

The current implementation still doesn't allow to use complete separated
meshes as we rely on structures which are not part of the private data
of a batman device.
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Documentation/CodingStyle sets a strongly prefered limit of 80
characters per line in "Chapter 2: Breaking long lines and strings".

Strings must be broken into smaller parts and long statements must be
rewritten.
Reported-by: NMikal Sande <mikal.sande@gmail.com>
Reported-by: NMark Rankilor <reodge@gmail.com>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Trailing spaces at the end of a line or before a tab are against
Documentation/CodingStyle "3.1: Spaces" and should be avoided. It is
also common style to add a single space after commas unless it is
followed either by a newline or a tab.
Reported-by: NMikal Sande <mikal.sande@gmail.com>
Reported-by: NLuis de Bethencourt <luisbg@ubuntu.com>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

BATMAN and broadcast packets are tracked with a sequence number window of
currently 64 entries to measure and avoid duplicates. Packets which have a
sequence number smaller than the newest received packet minus 64 are not
within this sequence number window anymore and are called "old packets"
from now on.

When old packets are received, the routing code assumes that the host of the
originator has been restarted. This assumption however might be wrong as
packets can also be delayed by NIC drivers, e.g. because of long queues or
collision detection in dense WiFi? environments. This behaviour can be
reproduced by doing a broadcast ping flood in a dense node environment.

The effect is that the sequence number window is jumping forth and back,
accepting and forwarding any packet (because packets are assumed to be "new")
and causing loops.

To overcome this problem, the sequence number handling has been reorganized.
When an old packet is received, the window is reset back only once. Other old
packets are dropped for (currently) 30 seconds to "protect" the new sequence
number and avoid the hopping as described above.

The reorganization brings some code cleanups (at least i hope you feel the
same) and also fixes a bug in count_real_packets() which falsely updated
the last_real_seqno for slightly older packets within the seqno window
if they are no duplicates.

This second version of the patch also fixes a problem where for seq_diff==64
bit_shift() reads from outside of the seqno window, and removes the loop
for seq_diff == -64 which was present in the first patch.

The third iteration also adds a window for the next expected sequence numbers.
This minimizes sequence number flapping for packets with very big differences
(e.g. 3 packets with seqno 0, 25000 and 50000 might still cause problems
without this window).
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Instead of having a single /proc file "interfaces" in which you have
to echo the wanted interface batman-adv will create a subfolder in each
suitable /sys/class/net folder. This subfolder contains files for the
interface specific settings. For example, mesh_iface to add/remove an
interface from a virtual mesh network (at the moment only bat0 is
supported).

Example:
echo bat0 > /sys/class/net/eth0/batman-adv/mesh_iface

to deactivate:
echo none > /sys/class/net/eth0/batman-adv/mesh_iface

Interfaces which are not compatible with batman-adv won't contain the
batman-adv folder, therefore can't be activated. Not supported are:
loopback, non-ethernet, non-ARP and virtual mesh network interfaces
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>