Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 23 11月, 2013 1 次提交
  3. 17 10月, 2013 3 次提交
    • P
      KVM: PPC: Book3S HV: Support POWER6 compatibility mode on POWER7 · 388cc6e1
      由 Paul Mackerras 提交于 
      This enables us to use the Processor Compatibility Register (PCR) on
POWER7 to put the processor into architecture 2.05 compatibility mode
when running a guest.  In this mode the new instructions and registers
that were introduced on POWER7 are disabled in user mode.  This
includes all the VSX facilities plus several other instructions such
as ldbrx, stdbrx, popcntw, popcntd, etc.

To select this mode, we have a new register accessible through the
set/get_one_reg interface, called KVM_REG_PPC_ARCH_COMPAT.  Setting
this to zero gives the full set of capabilities of the processor.
Setting it to one of the "logical" PVR values defined in PAPR puts
the vcpu into the compatibility mode for the corresponding
architecture level.  The supported values are:

0x0f000002	Architecture 2.05 (POWER6)
0x0f000003	Architecture 2.06 (POWER7)
0x0f100003	Architecture 2.06+ (POWER7+)

Since the PCR is per-core, the architecture compatibility level and
the corresponding PCR value are stored in the struct kvmppc_vcore, and
are therefore shared between all vcpus in a virtual core.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[agraf: squash in fix to add missing break statements and documentation]
Signed-off-by: NAlexander Graf <agraf@suse.de>
      388cc6e1
    • P
      KVM: PPC: Book3S HV: Store LPCR value for each virtual core · a0144e2a
      由 Paul Mackerras 提交于 
      This adds the ability to have a separate LPCR (Logical Partitioning
Control Register) value relating to a guest for each virtual core,
rather than only having a single value for the whole VM.  This
corresponds to what real POWER hardware does, where there is a LPCR
per CPU thread but most of the fields are required to have the same
value on all active threads in a core.

The per-virtual-core LPCR can be read and written using the
GET/SET_ONE_REG interface.  Userspace can can only modify the
following fields of the LPCR value:

DPFD	Default prefetch depth
ILE	Interrupt little-endian
TC	Translation control (secondary HPT hash group search disable)

We still maintain a per-VM default LPCR value in kvm->arch.lpcr, which
contains bits relating to memory management, i.e. the Virtualized
Partition Memory (VPM) bits and the bits relating to guest real mode.
When this default value is updated, the update needs to be propagated
to the per-vcore values, so we add a kvmppc_update_lpcr() helper to do
that.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[agraf: fix whitespace]
Signed-off-by: NAlexander Graf <agraf@suse.de>
      a0144e2a
    • P
      KVM: PPC: Book3S HV: Implement timebase offset for guests · 93b0f4dc
      由 Paul Mackerras 提交于 
      This allows guests to have a different timebase origin from the host.
This is needed for migration, where a guest can migrate from one host
to another and the two hosts might have a different timebase origin.
However, the timebase seen by the guest must not go backwards, and
should go forwards only by a small amount corresponding to the time
taken for the migration.

Therefore this provides a new per-vcpu value accessed via the one_reg
interface using the new KVM_REG_PPC_TB_OFFSET identifier.  This value
defaults to 0 and is not modified by KVM.  On entering the guest, this
value is added onto the timebase, and on exiting the guest, it is
subtracted from the timebase.

This is only supported for recent POWER hardware which has the TBU40
(timebase upper 40 bits) register.  Writing to the TBU40 register only
alters the upper 40 bits of the timebase, leaving the lower 24 bits
unchanged.  This provides a way to modify the timebase for guest
migration without disturbing the synchronization of the timebase
registers across CPU cores.  The kernel rounds up the value given
to a multiple of 2^24.

Timebase values stored in KVM structures (struct kvm_vcpu, struct
kvmppc_vcore, etc.) are stored as host timebase values.  The timebase
values in the dispatch trace log need to be guest timebase values,
however, since that is read directly by the guest.  This moves the
setting of vcpu->arch.dec_expires on guest exit to a point after we
have restored the host timebase so that vcpu->arch.dec_expires is a
host timebase value.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
      93b0f4dc
  5. 11 10月, 2013 1 次提交
  7. 05 9月, 2013 1 次提交
  9. 21 8月, 2013 2 次提交
    • S
      powerpc: Convert some mftb/mftbu into mfspr · beb2dc0a
      由 Scott Wood 提交于 
      Some CPUs (such as e500v1/v2) don't implement mftb and will take a
trap.  mfspr should work on everything that has a timebase, and is the
preferred instruction according to ISA v2.06.

Currently we get away with mftb on 85xx because the assembler converts
it to mfspr due to -Wa,-me500.  However, that flag has other effects
that are undesireable for certain targets (e.g.  lwsync is converted to
sync), and is hostile to multiplatform kernels.  Thus we would like to
stop setting it for all e500-family builds.

mftb/mftbu instances which are in 85xx code or common code are
converted.  Instances which will never run on 85xx are left alone.
Signed-off-by: NScott Wood <scottwood@freescale.com>
      beb2dc0a
    • S
      powerpc/fsl-booke: Work around erratum A-006958 · d52459ca
      由 Scott Wood 提交于 
      Erratum A-006598 says that 64-bit mftb is not atomic -- it's subject
to a similar race condition as doing mftbu/mftbl on 32-bit.  The lower
half of timebase is updated before the upper half; thus, we can share
the workaround for a similar bug on Cell.  This workaround involves
looping if the lower half of timebase is zero, thus avoiding the need
for a scratch register (other than CR0).  This workaround must be
avoided when the timebase is frozen, such as during the timebase sync
code.

This deals with kernel and vdso accesses, but other userspace accesses
will of course need to be fixed elsewhere.
Signed-off-by: NScott Wood <scottwood@freescale.com>
      d52459ca
  11. 14 8月, 2013 1 次提交
  13. 09 8月, 2013 1 次提交
  15. 24 7月, 2013 1 次提交
  17. 01 7月, 2013 2 次提交
  19. 01 6月, 2013 3 次提交
  21. 02 5月, 2013 3 次提交
  23. 27 4月, 2013 1 次提交
    • P
      KVM: PPC: Book3S HV: Improve real-mode handling of external interrupts · 4619ac88
      由 Paul Mackerras 提交于 
      This streamlines our handling of external interrupts that come in
while we're in the guest.  First, when waking up a hardware thread
that was napping, we split off the "napping due to H_CEDE" case
earlier, and use the code that handles an external interrupt (0x500)
in the guest to handle that too.  Secondly, the code that handles
those external interrupts now checks if any other thread is exiting
to the host before bouncing an external interrupt to the guest, and
also checks that there is actually an external interrupt pending for
the guest before setting the LPCR MER bit (mediated external request).

This also makes sure that we clear the "ceded" flag when we handle a
wakeup from cede in real mode, and fixes a potential infinite loop
in kvmppc_run_vcpu() which can occur if we ever end up with the ceded
flag set but MSR[EE] off.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
      4619ac88
  25. 26 4月, 2013 2 次提交
  27. 18 4月, 2013 1 次提交
  29. 05 3月, 2013 1 次提交
  31. 15 2月, 2013 3 次提交
  33. 13 2月, 2013 1 次提交
  35. 08 2月, 2013 1 次提交
  37. 10 1月, 2013 4 次提交
  39. 06 12月, 2012 1 次提交
    • P
      KVM: PPC: Book3S PR: Fix VSX handling · 28c483b6
      由 Paul Mackerras 提交于 
      This fixes various issues in how we were handling the VSX registers
that exist on POWER7 machines.  First, we were running off the end
of the current->thread.fpr[] array.  Ultimately this was because the
vcpu->arch.vsr[] array is sized to be able to store both the FP
registers and the extra VSX registers (i.e. 64 entries), but PR KVM
only uses it for the extra VSX registers (i.e. 32 entries).

Secondly, calling load_up_vsx() from C code is a really bad idea,
because it jumps to fast_exception_return at the end, rather than
returning with a blr instruction.  This was causing it to jump off
to a random location with random register contents, since it was using
the largely uninitialized stack frame created by kvmppc_load_up_vsx.

In fact, it isn't necessary to call either __giveup_vsx or load_up_vsx,
since giveup_fpu and load_up_fpu handle the extra VSX registers as well
as the standard FP registers on machines with VSX.  Also, since VSX
instructions can access the VMX registers and the FP registers as well
as the extra VSX registers, we have to load up the FP and VMX registers
before we can turn on the MSR_VSX bit for the guest.  Conversely, if
we save away any of the VSX or FP registers, we have to turn off MSR_VSX
for the guest.

To handle all this, it is more convenient for a single call to
kvmppc_giveup_ext() to handle all the state saving that needs to be done,
so we make it take a set of MSR bits rather than just one, and the switch
statement becomes a series of if statements.  Similarly kvmppc_handle_ext
needs to be able to load up more than one set of registers.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
      28c483b6
  41. 15 11月, 2012 2 次提交
  43. 27 9月, 2012 1 次提交
  45. 17 9月, 2012 1 次提交
  47. 10 9月, 2012 1 次提交
  49. 07 9月, 2012 1 次提交