With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.

As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch allows the Asus WL-BTD202 dongle to be used with a mono
headset without having to specify "options btusb force_scofix=1".

Based on a patch from Guillaume Bedot <littletux@zarb.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.

All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.

To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.

The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.

CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The old hci_usb driver has been fully replaced with the new btusb driver
and all major distributions switched to the new driver now. This removes
it since it should not be used at all anymore.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Following the pattern from hci_*.c, turn off BT_DBG messages unless
they have been requested via HCI_UART_DEBUG
Signed-off-by: NNick Pelly <npelly@google.com>
Acked-by: NBrian Swetland <swetland@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since size, addr, fcs, and tmp are unsigned, it would seem better to use
simple_strtoul that simple_strtol.

A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r2@
long e;
position p;
@@

e = simple_strtol@p(...)

@@
position p != r2.p;
type T;
T e;
@@

e =
- simple_strtol@p
+ simple_strtoul
  (...)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

After adding proper lockdep annotations for Bluetooth protocols the case
when lockdep is disabled produced two compiler warnings:

net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used
net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used

Fix both of them by adding a CONFIG_DEBUG_LOCK_ALLOC conditional around
them and re-arranging the code a little bit.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

    struct hci_dev_list_req {
            __u16  dev_num;
            struct hci_dev_req dev_req[0];  /* hci_dev_req structures */
    };

sizeof(struct hci_dev_list_req) == 4, so the two bytes immediately
following "dev_num" will never be initialized. When this structure
is copied to userspace, these uninitialized bytes are leaked.

Fix by using kzalloc() instead of kmalloc(). Found using kmemcheck.
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes accumulating of the header in case packet was requeued
in the error path.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During suspend it is important that all URBs are cancelled and then on
resume re-submitted. This gives initial suspend/resume support.

Based on initial work from Oliver Neukum <oneukum@suse.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With the addition of usb_unlink_anchored_urbs() it is possible to fully
control the bulk URBs from the notify callback. There is no need to
schedule work and so only do this for the ISOC URBs.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The URB submission routines need more fine grained control for the
mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to
better support different caller situations. Add a mem_flags parameter
and give the caller full control.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Join the move away from the obsolete info() macro, opencoding the
remaining uses. While we're at it, also get rid of the warn() macro
by promoting the three remaining uses to err().
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The N_GIGASET_M101 line discipline implemented by the ser_gigaset
driver does not transfer any data from/to userspace through the
tty interface. Therefore a poll method is not needed.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is_pure_response() does "ntohl(var) & const" and then
essentially just tests whether the result is 0 or not; this can be done
more efficiently by computing "var & htonl(const)" instead and doing the
byte swap at compile time instead of run time.

This change slightly shrinks the compiled code; eg on x86-64 we save a
couple of bswapl instructions:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function                                     old     new   delta
t3_sge_intr_msix_napi                        544     536      -8

and this also has the pleasant side effect of fixing a sparse warning:

    drivers/net/cxgb3/sge.c:2313:15: warning: restricted degrades to integer
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.

Suspend/resume alredy added.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the power management support into the physical
abstraction layer.

Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.

In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.

Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).

Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These warning originate from 50014f1b (ne2: convert to
net_device_ops) which did drop those functions.

drivers/net/ne2.c:140: warning: 'ne_open' declared 'static' but never defined
drivers/net/ne2.c:141: warning: 'ne_close' declared 'static' but never defined
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Impact: make global function static

Fix the following sparse warning:

  net/sched/sch_api.c:192:14: warning: symbol 'qdisc_match_from_root' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

validate_nla() currently doesn't allow empty nested attributes. This
makes userspace code unnecessarily complicated when starting and ending
the nested attribute is done by generic upper level code and the inner
attributes are dumped by a module.

Add a special case to accept empty nested attributes. When the nested
attribute is non empty, the same checks as before are performed.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:

	net/netfilter/nf_conntrack_netlink.c

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ixgbe_init_interrupt_scheme() is called from ixgbe_resume().  Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix missing label when CONFIG_PROC_FS=n:

net/sctp/protocol.c: In function 'sctp_proc_init':
net/sctp/protocol.c:106: error: label 'out_nomem' used but not defined
make[3]: *** [net/sctp/protocol.o] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the calls necessary to enable advanced error reporting for igb on
systems with AER enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: NSteven Whitehouse <swhiteho@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/hp-plus.c
	drivers/net/wireless/ath5k/base.c
	drivers/net/wireless/ath9k/recv.c
	net/wireless/reg.c

Update FW loading path to accomodate in-kernel images location
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include firmware and protocol images in the kernel image if requested
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add consistency in alloc_ring() parameter checking
to avoid potential memory leaks.
alloc_ring() callers are correct fo far.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix t3_eth_xmit() missing into the netdev_ops structure.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>