This patch adds the SMBus Device IDs for the Intel Wellsburg PCH
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This implements a very basic I2C host driver for the BCM2835 SoC. Missing
features so far are:

* 10-bit addressing.
* DMA.
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

The iSMT (Intel SMBus Message Transport) supports multi-master I2C/SMBus,
as well as IPMI.  It's operation is DMA-based and utilizes descriptors to
initiate transactions on the bus.

The iSMT hardware can act as both a master and a target, although this
driver only supports being a master.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NBill Brown <bill.e.brown@intel.com>
Tested-by: NSeth Heasley <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This adds the mfd cell to use the i2c part of the Nano River Technologies
viperboard as i2c master.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.

The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.

Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>

R-Car I2C is similar with SH7760 I2C.
But the SH7760 I2C driver had many workaround operations, since H/W had bugs.
Thus, it was pointless to keep compatible between SH7760 and R-Car I2C drivers.
This patch creates new Renesas R-Car I2C driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.

On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.

The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.

Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.

At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.

This closes kernel bug #43096.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.

The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.

[JD: Some adjustments.]

[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
   for most real-world applications including all SMBus transfer types.
   (The hardware does not support issuing arbitrary Sr conditions on the
    bus.)

testing: SoC: at91sam9g45
	 - BQ20Z80 battery SMBus client.
	 - on a 2.6.38 kernel with several i2c clients (temp-sensor,
	   audio-codec, touchscreen-controller, w1-bridge, io-expanders)
Signed-off-by: NNikolaus Voss <n.voss@weinmann.de>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NHubert Feurstein <h.feurstein@gmail.com>
Tested-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: NNicolas Ferre <nicolas.ferre@atmel.com>

[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
        i2c: at91: use managed resources
        i2c: at91: add warning about transmission issues for some devices
        i2c: at91: use an id table for SoC dependent parameters
]
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.

Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.

This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:

  LD      drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NJiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]

Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.
Signed-off-by: NRoland Stigge <stigge@antcom.de>

Some AMD chipsets, such as the SP5100, have an auxiliary SMBus
controller with a second set of registers. This patch adds
support for this auxiliary controller.

Tested on ASUS KCMA-D8 motherboard.
Signed-off-by: NAndrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

As git history indicates, the driver predates the git era and is heavily
used and worked on since. Not EXPERIMENTAL anymore.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Florian Fainelli <ffainelli@freebox.fr>

The gateware device has been used outside of the Nomadik world, using
the pci-amba bridge driver, so loosen the dependencies.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The platform is removed, so there are no users of this driver.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The former mach specific reset_block function has been converted to a global
one. Use the new one to remove mach dependency from the driver.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Correct spelling typo in various Kconfig file.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add the SMBus controller device IDs for the Intel Lynx Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

SiRFprimaII is the latest generation application processor from CSR’s
multi-function SoC product family.
The SoC support codes are in arch/arm/mach-prima2 from Linux mainline
3.0.
There are two I2C controllers on primaII, features include:
* Two I2C controller modules are on chip
* RISC I/O bus read write register
* Up to 16 bytes data buffer for issuing commands and writing data
  at the same time
* Up to 16 commands, and receiving read data 16 bytes at a time
* Error INT report (ACK check)
* No-ACK bus protocols (SCCB bus protocols)
Signed-off-by: NZhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: NXiangzhen Ye <Xiangzhen.Ye@csr.com>
Signed-off-by: NYuping Luo <Yuping.Luo@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Move Kconfig option for I2C_EG20T to the correct position and keep
the options sorted.

Also, use tabs in Makefile and move the I2C_EG20T entry to its
position.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Add support for the intergrated I2C controller on Netlogic
XLR/XLS MIPS SoC.

The changes are to add a new file i2c/buses/i2c-xlr.c, containing the
i2c bus implementation, and to update i2c/buses/{Kconfig,Makefile} to
add the CONFIG_I2C_XLR option.
Signed-off-by: NGanesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On m68k, I get:

drivers/i2c/busses/i2c-elektor.c: In function ‘pcf_isa_init’:
drivers/i2c/busses/i2c-elektor.c:153: error: implicit declaration of function ‘ioport_map’
drivers/i2c/busses/i2c-elektor.c:153: warning: assignment makes pointer from integer without a cast
drivers/i2c/busses/i2c-elektor.c: In function ‘elektor_probe’:
drivers/i2c/busses/i2c-elektor.c:287: error: implicit declaration of function ‘ioport_unmap’

Since commit 82ed223c ("iomap: make IOPORT/PCI
mapping functions conditional"), ioport_map() is only available on platforms
that set HAS_IOPORT.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch splits i2c-designware.c into three pieces:
     i2c-designware-core.c, contains the code that interacts directly
     with the core.

     i2c-designware-platdrv.c, contains the code specific to the
     platform driver using the core.

     i2c-designware-core.h contains the definitions and declareations
     shared by i2c-designware-core.c and i2c-designware-platdrv.c.

This patch is the first in a set to allow multiple instances of the
designware I2C core in the system.
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Now that no driver any longer depends on the CONFIG_SOC_AU1???  symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files.  Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We currently have two symbols to control compilation the MFD subsystem,
MFD_SUPPORT and MFD_CORE. The MFD_SUPPORT is actually not required
at all, it only hides the submenu when not set, with the effect that
Kconfig warns about missing dependencies when another driver selects
an MFD driver while MFD_SUPPORT is disabled. Turning the MFD submenu
back from menuconfig into a plain menu simplifies the Kconfig syntax
for those kinds of users and avoids the surprise when the menu
suddenly appears because another driver was enabled that selects this
symbol.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Don't let other driver config options influence us, as it makes the
code more complex and fragile for a small benefit. There's nothing
wrong with instantiating I2C devices even if they don't have a driver.
And we're talking about 835 extra bytes in the binary on x86-64,
that's hardly worth arguing about.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: David Woodhouse <david.woodhouse@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>

This patch adds the SMBus controller DeviceID for the Intel Panther Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The Sodaville I2C controller is almost the same as found on PXA2xx. The
difference:
- the register are at a different offset
- no slave support

The PCI probe code adds three platform devices which are probed then by
the platform code.
The X86 part also adds dummy clock defines because we don't have HW
clock support.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the SMBus Controller DeviceIDs for the Intel DH89xxCC PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

change from original version -- by advice of Jean Delvare
1. remove global variable i2c_reg, replaced by local variables
2. replace ENXIO with ENODEV when no platform resources
3. add adapter->nr assignment before i2c_add_numbered_adapter() call
4. add judgement for i2c_del_adapter() return value
5. release adapter when driver removed
6. add __devexit for puv3_i2c_remove() function
7. modify several names to more appropriated ones
Signed-off-by: NGuan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Currently i2c-mpc supports 32bit system only, this modification makes it
supported on both 32-bit and 64-bit systems.  The P5020 is the first
64-bit PPC system with the i2c-mpc controller.

Based in patch from Xulei <B33228@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>