The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

TWL6040 is used only with OMAP4/5 SoCs and they can only boot in in DT mode.
The support for pdata/legacy boot can be removed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

By using devm functions we can get a simpler code.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Convert gpio-tz1090 driver to use generic irqchips. This allows the
irq_ack, irq_mask, and irq_unmask callbacks and associated helper
functions to be removed. Also switch to using irq_setup_alt_chip() in
the irq_set_type callback instead of using __irq_set_handler_locked().
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.

The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.

Changes in v4:
 - fix typos in DT bindings compatible properties
 - reference Documentation/devicetree/bindings/gpio/gpio.txt in
   gpio-ranges description in DT bindings
 - fix gpio-ranges examples in DT bindings (it must now have 3 cells)

Changes in v3:
 - separated from irq-imgpdc and removed arch/metag changes to allow
   these patches to go upstream separately via the pinctrl[/gpio] trees
   (particularly the pinctrl drivers depend on the new pinconf DT
   bindings).
 - some s/unsigned/unsigned int/.
 - gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
   <dt-bindings/interrupt-controller/irq.h> flags in bindings.
 - gpio-tz1090*: move initcall from postcore to subsys.

Changes in v2:
 - gpio-tz1090-pdc: remove references to Linux flags in dt bindings
 - gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
 - gpio-tz1090-pdc: make register accessors inline to match pinctrl
 - gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
   breakage
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC.
This doesn't include low-power GPIOs as they're controlled separately
via the Powerdown Controller (PDC) registers.

The driver is instantiated by device tree and supports interrupts for
all GPIOs.

Changes in v4:
 - fix typos in DT bindings compatible properties
 - reference Documentation/devicetree/bindings/gpio/gpio.txt in
   gpio-ranges description in DT bindings
 - fix gpio-ranges examples in DT bindings (it must now have 3 cells)
 - gpio-tz1090: use of_property_read_u32 instead of of_get_property

Changes in v3:
 - separated from irq-imgpdc and removed arch/metag changes to allow
   these patches to go upstream separately via the pinctrl[/gpio] trees
   (particularly the pinctrl drivers depend on the new pinconf DT
   bindings).
 - some s/unsigned/unsigned int/.
 - some s/unsigned int/bool/ and use of BIT().
 - gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
   <dt-bindings/interrupt-controller/irq.h> flags in bindings.
 - gpio-tz1090*: move initcall from postcore to subsys.
 - gpio-tz1090: add REG_ prefix to some constants for consistency.
 - gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge
   cunningness.

Changes in v2:
 - gpio-tz1090: remove references to Linux flags in dt bindings
 - gpio-tz1090: make use of BIT() from linux/bitops.h
 - gpio-tz1090: make register accessors inline to match pinctrl
 - gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI
   breakage
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

this bug:
https://bugzilla.redhat.com/show_bug.cgi?id=951695

Reported a dma debug backtrace:

WARNING: at lib/dma-debug.c:937 check_unmap+0x47d/0x930()
Hardware name: To Be Filled By O.E.M.
via-rhine 0000:00:12.0: DMA-API: device driver failed to check map error[device
address=0x0000000075a837b2] [size=90 bytes] [mapped as single]
Modules linked in: ip6_tables gspca_spca561 gspca_main videodev media
snd_hda_codec_realtek snd_hda_intel i2c_viapro snd_hda_codec snd_hwdep snd_seq
ppdev mperf via_rhine coretemp snd_pcm mii microcode snd_page_alloc snd_timer
snd_mpu401 snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore parport_pc
parport shpchp ata_generic pata_acpi radeon i2c_algo_bit drm_kms_helper ttm drm
pata_via sata_via i2c_core uinput
Pid: 295, comm: systemd-journal Not tainted 3.9.0-0.rc6.git2.1.fc20.x86_64 #1
Call Trace:
 <IRQ>  [<ffffffff81068dd0>] warn_slowpath_common+0x70/0xa0
 [<ffffffff81068e4c>] warn_slowpath_fmt+0x4c/0x50
 [<ffffffff8137ec6d>] check_unmap+0x47d/0x930
 [<ffffffff810ace9f>] ? local_clock+0x5f/0x70
 [<ffffffff8137f17f>] debug_dma_unmap_page+0x5f/0x70
 [<ffffffffa0225edc>] ? rhine_ack_events.isra.14+0x3c/0x50 [via_rhine]
 [<ffffffffa02275f8>] rhine_napipoll+0x1d8/0xd80 [via_rhine]
 [<ffffffff815d3d51>] ? net_rx_action+0xa1/0x380
 [<ffffffff815d3e22>] net_rx_action+0x172/0x380
 [<ffffffff8107345f>] __do_softirq+0xff/0x400
 [<ffffffff81073925>] irq_exit+0xb5/0xc0
 [<ffffffff81724cd6>] do_IRQ+0x56/0xc0
 [<ffffffff81719ff2>] common_interrupt+0x72/0x72
 <EOI>  [<ffffffff8170ff57>] ? __slab_alloc+0x4c2/0x526
 [<ffffffff811992e0>] ? mmap_region+0x2b0/0x5a0
 [<ffffffff810d5807>] ? __lock_is_held+0x57/0x80
 [<ffffffff811992e0>] ? mmap_region+0x2b0/0x5a0
 [<ffffffff811bf1bf>] kmem_cache_alloc+0x2df/0x360
 [<ffffffff811992e0>] mmap_region+0x2b0/0x5a0
 [<ffffffff811998e6>] do_mmap_pgoff+0x316/0x3d0
 [<ffffffff81183ca0>] vm_mmap_pgoff+0x90/0xc0
 [<ffffffff81197d6c>] sys_mmap_pgoff+0x4c/0x190
 [<ffffffff81367d7e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
 [<ffffffff8101eb42>] sys_mmap+0x22/0x30
 [<ffffffff81722fd9>] system_call_fastpath+0x16/0x1b

Usual problem with the usual fix, add the appropriate calls to dma_mapping_error
where appropriate

Untested, as I don't have hardware, but its pretty straightforward
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: David S. Miller <davem@davemloft.net>
CC: Roger Luethi <rl@hellgate.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently had this backtrace reported:
WARNING: at lib/dma-debug.c:937 check_unmap+0x47d/0x930()
Hardware name: System Product Name
ATL1E 0000:02:00.0: DMA-API: device driver failed to check map error[device
address=0x00000000cbfd1000] [size=90 bytes] [mapped as single]
Modules linked in: xt_conntrack nf_conntrack ebtable_filter ebtables
ip6table_filter ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek iTCO_wdt
iTCO_vendor_support snd_hda_intel acpi_cpufreq mperf coretemp btrfs zlib_deflate
snd_hda_codec snd_hwdep microcode raid6_pq libcrc32c snd_seq usblp serio_raw xor
snd_seq_device joydev snd_pcm snd_page_alloc snd_timer snd lpc_ich i2c_i801
soundcore mfd_core atl1e asus_atk0110 ata_generic pata_acpi radeon i2c_algo_bit
drm_kms_helper ttm drm i2c_core pata_marvell uinput
Pid: 314, comm: systemd-journal Not tainted 3.9.0-0.rc6.git2.3.fc19.x86_64 #1
Call Trace:
 <IRQ>  [<ffffffff81069106>] warn_slowpath_common+0x66/0x80
 [<ffffffff8106916c>] warn_slowpath_fmt+0x4c/0x50
 [<ffffffff8138151d>] check_unmap+0x47d/0x930
 [<ffffffff810ad048>] ? sched_clock_cpu+0xa8/0x100
 [<ffffffff81381a2f>] debug_dma_unmap_page+0x5f/0x70
 [<ffffffff8137ce30>] ? unmap_single+0x20/0x30
 [<ffffffffa01569a1>] atl1e_intr+0x3a1/0x5b0 [atl1e]
 [<ffffffff810d53fd>] ? trace_hardirqs_off+0xd/0x10
 [<ffffffff81119636>] handle_irq_event_percpu+0x56/0x390
 [<ffffffff811199ad>] handle_irq_event+0x3d/0x60
 [<ffffffff8111cb6a>] handle_fasteoi_irq+0x5a/0x100
 [<ffffffff8101c36f>] handle_irq+0xbf/0x150
 [<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50
 [<ffffffff81073b10>] ? irq_enter+0x50/0xa0
 [<ffffffff8172738d>] do_IRQ+0x4d/0xc0
 [<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50
 [<ffffffff8171c6b2>] common_interrupt+0x72/0x72
 <EOI>  [<ffffffff810db5b2>] ? lock_release+0xc2/0x310
 [<ffffffff8109ea04>] lg_local_unlock_cpu+0x24/0x50
 [<ffffffff811dcb2f>] file_sb_list_del+0x3f/0x50
 [<ffffffff811dcb6d>] fput+0x2d/0xc0
 [<ffffffff811d8ea1>] filp_close+0x61/0x90
 [<ffffffff811fae4d>] __close_fd+0x8d/0x150
 [<ffffffff811d8ef0>] sys_close+0x20/0x50
 [<ffffffff81725699>] system_call_fastpath+0x16/0x1b

The usual straighforward failure to check for dma_mapping_error after a map
operation is completed.

This patch should fix it, the reporter wandered off after filing this bz:
https://bugzilla.redhat.com/show_bug.cgi?id=954170

and I don't have hardware to test, but the fix is pretty straightforward, so I
figured I'd post it for review.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

>> drivers/net/usb/r815x.c:38:16: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:67:15: sparse: cast to restricted __le32
>> drivers/net/usb/r815x.c:69:13: sparse: incorrect type in assignment (different base types)
   drivers/net/usb/r815x.c:69:13:    expected unsigned int [unsigned] [addressable] [assigned] [usertype] tmp
   drivers/net/usb/r815x.c:69:13:    got restricted __le32 [usertype] <noident>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Spotted-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

config: make ARCH=avr32 allyesconfig
drivers/net/usb/r8152.c: In function 'rtl8152_start_xmit':
drivers/net/usb/r8152.c:956: warning: integer overflow in expression

   955	memset(tx_desc, 0, sizeof(*tx_desc));
 > 956	tx_desc->opts1 = cpu_to_le32((len & TX_LEN_MASK) | TX_FS | TX_LS);
   957	tp->tx_skb = skb;
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Spotted-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.

Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.

Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.

Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Base on cdc_ether, add the mii functions for RTL8152 and RTL8153.
The RTL8152 and RTL8153 support ECM mode which use the driver of
cdc_ether. Add the mii functions. Then, the basic PHY access is
possible.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch adds code to log SDMA errors for supportability purposes.
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The vzalloc()'ed field physshadow is leaked on module unload.

This patch adds vfree after the sibling page shadow is freed.
Reported-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz.

Fix the declaration of this field to be __be16 (which is what is in
the firmware spec), renaming the field to log_uar_pg_size to conform
to the spec, which fixes the endianness bug reported by sparse.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

If the transport layer is offline it is more appropriate to let
srp_abort() return FAST_IO_FAIL instead of SUCCESS.
Reported-by: NSebastian Riemer <sebastian.riemer@profitbricks.com>
Acked-by: NDavid Dillow <dillowda@ornl.gov>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.
Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
----
drivers/watchdog/hpwdt.c |    9 ++++++---
 1 files changed, 6 insertions(+), 3 deletions(-)

In watchdog_ping(), 'start' is called automatically when 'ping' function call
is not configured.
Softdog driver has same handling in both cases - start and ping, so 'ping' OPS
can be removed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to
clear.  If we read the register, mask off the watchdog bit, and
write it back, we're actually clearing every interrupt which wasn't
pending at the time we read the register - and that is racy.

Fix this to only write ~WATCHDOG_BIT to the register, which means
we write as zero only the watchdog bit.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove.  The only things
missing are a few register settings in Dove's bridge-regs.h.

Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org

Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().

Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.

There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.

In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):

http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Watchdog 1.01.a is also compatible with 1.00.a.
Add the origin version to compatible list.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

- Remove reference for IP version
- Fix header coding style
- Remove notes which are visible from the code
- Fix driver license according to header
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Kernel has nice helpers to dump buffers.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

A watchdog device may be stopped from userspace using WDIOC_SETOPTIONS
ioctl and flag WDIOS_DISABLECARD. If the device is closed after this
operation, watchdog_release() is called and status bits checked for
stopping it. Besides, if the device has not been unregistered a critical
message "watchdog did not stop!" is printed, although the ioctl may have
successfully stopped it already.

Without the patch a user application sample code like this will successfully
stop the watchdog, but the kernel will output the message
"watchdog did not stop!":

	wd_fd = open("/dev/watchdog", O_RDWR);

	flags = WDIOS_DISABLECARD;
	ioctl(wd_fd, WDIOC_SETOPTIONS, &flags);

	close(wd_fd);
Signed-off-by: NHector Palacios <hector.palacios@digi.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

In preparation to switching the jz4740 clk driver to the common clk framework
make sure to pass the device to clk_get().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Instead of using legacy suspend/resume methods, using newer
dev_pm_ops structure allows better control over power management.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

dev_err()/dev_info() are more preferred than pr_err()/pr_info().
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>