from whitespace cleaning script
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If an eeprom defined two tuners and they supported more than eight
standards combined (as opposed to each), it would overflow an array. 
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c: In function 'set_standard':
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c:33: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'v4l2_std_id'
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NYeasah Pell <yeasah@schwide.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Tested on x64 with a bttv board. Most Get ioctls are fixed. The only
non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the
same results on x86_64 and i386 architectures.
Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this
patch and tests on ppc64.
Signed-off-by: NAlastair Poole <netstar@gatheringofgray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible.  On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface.  It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed.  Do this for the affected boards.  Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Just a few adjustments were required on those drivers to be V4L2 compliant.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Compile-tested only (no hardware)
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove buggy dvb_detach() macro and replace with unified
dvb_frontend_detach() call.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Replaced with dvb_attach()
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This change causes the pvrusb2 driver to limit horizontal resolution
to be only 720 if 24xxx device hardware is being used.  This is a
workaround for an unsolved problem in the driver where if the
resolution is set to something other than 720 the video quality will
be _seriously_ degraded.  It only happens on 24xxx devices (29xxx are
unaffected by the problem and unaffected by this change).  Once the
problem is finally solved, this small change can be removed.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The internal control implementation in the pvrusb2 driver normally
encodes integer range limits using literal values in a const
structure.  This change adds two function pointers, which if not null
will be called through in order to determine integer min / max
values.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The pvrusb2 implementation for VIDIOC_[S|TRY]_FMT was hardcoding
limits on the range for allowed resolution, but it would be much
better if we instead just queried the internal control for these
values.  This then opens the door for the driver to adjust these
limits based on the detected hardware.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix a few miscellaneous issues in the pvrusb2 driver related to use of
the new mpeg controls.  This also should fix problems involving
update of the saa7115 / cx25840 configuration as control changes are made.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A buffer was set just before an if block, and then again in both branches
of the if.  Obvious coding error.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for Shenzhen Tungsten Ages Tech TE-DTV-250 OEM for
Swann PCI TV Tuner Card
Signed-off-by: NDavid Bussenschutt <buzz@oska.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: NPeter Naulls <peter@chocky.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds autodetection support for the AverMedia M150-D
blackbird MPEG encoder / analog video capture card.
This board is known to work with the ASUS PVR 416 configuration.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

add initial support for Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
only analog is working for now
Signed-off-by: NEric Thomas <ethomas@claranet.fr>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since kernel include autoconf.h via command line, those config.h inclusion
can be removed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It is just another Lifeview clone
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The change is just an additional PCI ID
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Analog TV, CVBS, S-video and DVB-T are working,
DVB-S not yet
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The v4l2 API documentation for VIDIOC_ENUMSTD says:

	To enumerate all standards applications shall begin at index
	zero, incrementing by one until the driver returns EINVAL.

The actual code, however, tests the index this way:

               if (index<=0 || index >= vfd->tvnormsize) {
                        ret=-EINVAL;

So any application which passes in index=0 gets EINVAL right off the bat
- and, in fact, this is what happens to mplayer.  So I think the
following patch is called for, and maybe even appropriate for a 2.6.18.x
stable release.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Several DVB modules depends on I2C
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

V4L1 support should be disabled when no CONFIG_VIDEO_V4L1_COMPAT is defined,
to allow checking for broken V4L2 ports. This is very important during the
migration phase for V4L2 API.
However, userspace apps should be capable of using both APIs, since they need
to test at runtime, via VIDIOCGCAP ioctl, if V4L1 is supported. So, when
__KERNEL__ is not defined, those ioctls and corresponding structs should be
visible.
This patch also removes the obsolete defines HAVE_V4L1 and HAVE_V4L2, that
where causing some confusion, and were replaced by CONFIG_VIDEO_V4L1_COMPAT
and CONFIG_VIDEO_V4L2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Previously, this were reported:
	Ooops: IR config error [card=139]
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The tena_9533_di_pal_ranges use 0x04 instead the original 0x08 for the
UHF (range 2) switching. This is wrong and therefore nothing happens.
Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to make the UHF switch
working again.
Signed-off-by: NHermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In bugzilla #6943, Maxim Britov reported:
"I can enable Logitech quickcam support in .config, but it want be compile.
I have to add into drivers/media/video/Makefile:
obj-$(CONFIG_USB_QUICKCAM_MESSENGER)    += usbvideo/"
He's right, just enable that driver as module while disabling every other
driver that gets into that directory, nothing will get compiled.
This patch fixes the Makefile.
Signed-off-by: NDiego Calleja <diegocg@gmail.com>
Acked-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Without the LNA these tuners perform very poorly (read 'unwatchable') when
the signal is weak.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>