Just powering on, these devices below wait to download firmware.
 - Firewire Audiophile
 - Firewire 410
 - Firewire 1814
 - ProjectMix I/O

But firmware version 5058 or later, flash memory in the device stores the
firmware. So this driver can enable these devices by sending a certain cue to
load the firmware.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit allows this driver to support some models which M-Audio produces
with DM1000 but its firmware is special. They are:
 - Firewire 1814
 - ProjectMix I/O

They have heavily customized firmware. The usual operations can't be applied to
them. For this reason, this commit adds a model specific member to 'struct
snd_bebob' and some model specific functions. Some parameters are write-only so
this commit also adds control interface for applications to set them.

M-Audio special firmware quirks:
 - Just after powering on, they wait to download firmware. This state is
   changed when receiving cue. Then bus reset is generated and the device is
   recognized as a different model with the uploaded firmware.
 - They don't respond against BridgeCo AV/C extension commands. So drivers
   can't get their stream formations and so on.
 - They do not start to transmit packets only by establishing connection but
   also by receiving SIGNAL FORMAT command.
 - After booting up, they often fail to send response against driver's request
   due to mismatch of gap_count.

This module don't support to upload firmware.

Tested-by: Darren Anderson <darrena092@gmail.com> (ProjectMix I/O)
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit allows this driver to support some models which M-Audio produces
with DM1000/DM1000E with usual firmware. They are:
 - Firewire 410
 - Firewire AudioPhile
 - Firewire Solo
 - Ozonic
 - NRV10
 - FirewireLightBridge

According to a person who worked in BridgeCo, some models are produced with
'Pre-BeBoB'. This means that these products were released before BeBoB was
officially produced, and later BeBoB specification was formed. So these models
have some quirks.

M-Audio usual firmware quirks:
 - Just after powering on, 'Firewire 410' waits to download firmware. This
   state is changed when receiving cue. Then bus reset is generated and the
   device is recognized as a different model with the uploaded firmware.
 - 'Firewire Audiophile' also waits to download firmware but its
   vendor id/model id is the same as the one after loading firmware.
 - The information of channel mapping for MIDI conformant data channel is
   invalid against BridgeCo specification.

This commit adds some codes for these quirks but don't support to upload
firmware.

This commit also adds specific operations to get metering information. The
metering information also includes status of clock synchronization if the model
supports to switch source of clock.

The specification of FirewireLightBridge is unknown. So in this time, normal
operations are applied for this model.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit allows this driver to support all of models which Focusrite
produces with DM1000/BeBoB. They are:
 - Saffire
 - Saffire LE
 - SaffirePro 10 I/O
 - SaffirePro 26 I/O

This commit adds Focusrite specific operations:
1. Get source of clock
2. Get/Set sampling frequency
3. Get metering information

The driver uses these functionalities to read/write specific address by async
transaction.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit allows this driver to support all of models which Yamaha produced
with DM1000/BeBoB. They are:
 - GO44
 - GO46

This commit adds Yamaha specific operations. To get source of clock, AV/C Audio
Subunit command is used.

I note that their appearances are similar to some models of TerraTec; 'Go44' is
similar to 'PHASE 24 FW' and 'GO46' is similar to 'PHASE X24 FW'. But their
combination of Audio/Music subunits is a bit different.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit allows this driver to support all of models which Terratec produced
with DM1000/BeBoB. They are:
 - PHASE 24 FW
 - PHASE X24 FW
 - PHASE 88 Rack FW
 - EWS MIC2
 - EWS MIC4
 - Aureon 7.1 Firewire

For Phase series, this commit adds a Terratec specific operation. To get source
of clock. AV/C Audio Subunit command is used.

For EWS series and Aureon, this module uses normal operations.

Tested-by: Maximilian Engelhardt <maxi@daemonizer.de> (PHASE 24 FW)
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit is for some devices which have its own operations or quirks.

Many functionality should be implemented in user land. Then this commit adds
functionality related to stream such as sampling frequency or clock source. For
help to debug, this commit adds the functionality to get metering information
if it's available.

To help these functionalities, this commit adds some AV/C commands defined in
'AV/C Audio Subunit Specification (1394TA).
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This interface is designed for mixer/control application. By using hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds a functionality to capture/playback PCM samples.

When AMDTP stream is already running for PCM or the source of clock is not
internal, available sampling rate is limited at current one.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds a functionality to capture/playback MIDI messages.

When no AMDTP streams are running, this module starts AMDTP stream at current
sampling rate for MIDI substream.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds proc interface to get these information for debugging:
 - firmware information
 - stream formation
 - current clock source and sampling rate
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Normal BeBoB firmware has a quirk. When receiving bus reset, it transmits
packets with discontinuous value in dbc field.

This causes two situation, one is to abort streaming by firewire-lib as a
result of detecting the discontinuity. Another is to call driver's .update()
because of bus reset. These two is generated independently. (The former
depends on isochronous stream and the latter depends on IEEE1394 bus driver.)

When BeBoB driver works with XRUN-recoverable applications, this situation
looks like stream_start_duplex() call followed by stream_update_duplex() call
because applications will call snd_pcm_prepare() immediately at XRUN.

To update connections and streams at first, this commit use completion. When
queueing error occurs, stream_start_duplex() is forced to wait maximum
1000msec. During this, when .update() is called, the completion is waken and
stream_start_duplex() is processed without breaking connections.

At bus reset, stream_start_duplex() shouldn't break/establish connections and
stream_update_duplex() should update connections because a caller of
fw_iso_resources_allocate() is responsible for calling
fw_iso_resources_update() on bus reset.

This commit also adds a flag, which has an effect to skip checking continuity
for first packet. This flag is useful for BeBoB quirk to start handling packets
during streaming.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds management functionality for connections and streams.
BeBoB uses CMP to manage connections and uses AMDTP for streams.

This commit also adds some BridgeCo's AV/C extension commands. There are some
BridgeCo's AV/C extension commands but this commit just uses below commands
to get device's capability and status:

 1.Extended Plug Info commands
  - Plug Channel Position Specific Data
  - Plug Type Specific Data
  - Cluster(Section) Info Specific Data
  - Plug Input Specific Data
 2.Extended Stream Format Information commands
  - Extended Stream Format Information Command - List Request

For Extended Plug Info commands for Cluster Info Specific Data, I pick up
'section' instead of 'cluster' from document to prevent from misunderstanding
because 'cluster' is also used in IEC 61883-6.
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds a new driver for BeBoB based devices with no specific
operations. Currently this driver just create/remove card instance according
to callbacks.

BeBoB is 'BridgeCo enhanced Breakout Box'. This is installed to firewire
devices with DM1000/DM1100/DM1500 chipset. It gives common way for host
system to handle BeBoB based devices.

Current supported devices:
 - Edirol FA-66/FA-101
 - PreSonus FIREBOX/FIREPOD/FP10/Inspire1394
 - BridgeCo RDAudio1/Audio5
 - Mackie Onyx 1220/1620/1640 (Firewire I/O Card)
 - Mackie d.2 (Firewire Option)
 - Stanton FinalScratch 2 (ScratchAmp)
 - Tascam IF-FW DM
 - Behringer XENIX UFX 1204/1604
 - Behringer Digital Mixer X32 series (X-UF Card)
 - Apogee Rosetta 200/Rosetta 400 (X-FireWire card)
 - Apogee DA-16X/AD-16X/DD-16X (X-FireWire card)
 - Apogee Ensemble
 - ESI Quotafire610
 - AcousticReality eARMasterOne
 - CME MatrixKFW
 - Phonix Helix Board 12 MkII/18 MkII/24 MkII
 - Phonic Helix Board 12 Universal/18 Universal/24 Universal
 - Lynx Aurora 8/16 (LT-FW)
 - ICON FireXon
 - PrismSound Orpheus/ADA-8XR

Devices possible to be supported if identifying IDs:
 - Apogee Mini-Me Firewire/Mini-DAC Firewire
 - Behringer F-Control Audio 610/1616
 - Cakewalk Sonar Power Studio 66
 - CME UF400e
 - ESI Quotafire XL
 - Infrasonic DewX/Windy6
 - Mackie Digital X Bus x.200/400
 - Phonic Helix Board 12/18/24
 - Phonic FireFly 202/302
 - Rolf Spuler Firewire Guitar
Tested-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>