Currently, we've got the less than ideal situation where if we need to
allocate a 256MB mapping we'll allocate four entries like so,

	 entry 1: 128MB
	 entry 2:  64MB
	 entry 3:  16MB
	 entry 4:  16MB

This is because as we execute the loop in pmb_remap() we will
progressively try mapping the remaining address space with smaller and
smaller sizes. This isn't good because the size we use on one iteration
may be the perfect size to use on the next iteration, for instance when
the initial size is divisible by one of the PMB mapping sizes.

With this patch, we now only need two entries in the PMB to map 256MB of
address space,

	  entry 1: 128MB
	  entry 2: 128MB
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We should favour PMB mappings when the physical address cannot be
reached with 29-bits.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

If we fail to allocate a PMB entry in pmb_remap() we must remember to
clear and free any PMB entries that we may have previously allocated,
e.g. if we were allocating a multiple entry mapping.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix some callers of jump_to_uncached() and back_to_cached() that were
not annotated with __uses_jump_to_uncached.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Extend the ecovec24 board code to enable Power
Management LEDs showing the current sh7724 sleep state.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Rework the r8a66597-udc fifo code to avoid unaligned accesses.

Without this patch unaligned exceptions will degrade the
USB performance. The exceptions come from the fact that
the usb fifo data buffers may be misaligned.

This patch updates the fifo access code to only use
insl()/outsl() and insw()/outsw() in the case of properly
aligned data buffers. The fallback case is that inl()/inw()
are used for misaligned buffer reads together with outb()
that is used for misaligned buffer writes.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

ERROR: "__movmem" [net/irda/irda.ko] undefined!
ERROR: "__movmem" [fs/nfsd/nfsd.ko] undefined!
ERROR: "__movmem" [fs/lockd/lockd.ko] undefined!
ERROR: "__movmem" [crypto/sha1_generic.ko] undefined!
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Certain networking and USB workloads generate floods of these accesses,
so just disable it by default (thereby restoring the old behaviour). The
option remains configurable from userspace, and can still be used as a
debugging aid.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Tested-by: NYusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There is now no need for the magicpanelr2 and dreamcast platforms to set
their own I/O port bas values, given that the generic machvec code now
sets this to P2SEG for everyone.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There's already code in do_page_fault() to conditionally enable
interrupts, so we don't need to unconditonally enable them before
calling it. This fixes a lockdep warning where we called
trace_hardirqs_off() but with irqs still enabled.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This bumps up the default I/O base to P2SEG, which allows legacy probing
to bail out gracefully rather than oopsing. Platforms that have a real
PIO offset still need to fix this up on their own, although most
platforms are content with P2SEG already.

The previous change to teach ioport_map() about >= P1SEG offsets in
combination with this patch allows both the already remapped and the
legacy address probing to pass through and succeed.

Fixes up an oops with i8042 on the sh7785lcr board.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up the case where certain drivers already do their own
remapping and subsequently attempt to use the PIO calls for I/O. In this
case there is no additional remapping that needs to be done, and the
address can be casted in to the cookie directly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

.. duplicated by merging the same fix twice, for details see commit
0d9df251 ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes")
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following commit made console open fails while booting:

	commit b50989dc
	Author: Alan Cox <alan@linux.intel.com>
	Date:   Sat Sep 19 13:13:22 2009 -0700

	tty: make the kref destructor occur asynchronously

Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:

INIT open /dev/console Input/output error

It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229

The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.

Fix it as per the following Alan's suggestion:

  Fun but it's actually not a bug and the fix is wrong in itself as
  the port may be closing but not yet being destructed, in which case
  it seems to do the wrong thing.  Opening a tty that is closing (and
  could be closing for long periods) is supposed to return -EIO.

  I suspect a better way to deal with this and keep the old console
  timing is to split tty->shutdown into two functions.

  tty->shutdown() - called synchronously just before we dump the tty
  onto the waitqueue for destruction

  tty->cleanup() - called when the destructor runs.

  We would then do the shutdown part which can occur in IRQ context
  fine, before queueing the rest of the release (from tty->magic = 0
  ...  the end) to occur asynchronously

  The USB update in -next would then need a call like

       if (tty->cleanup)
               tty->cleanup(tty);

  at the top of the async function and the USB shutdown to be split
  between shutdown and cleanup as the USB resource cleanup and final
  tidy cannot occur synchronously as it needs to sleep.

  In other words the logic becomes

       final kref put
               make object unfindable

       async
               clean it up
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ]
Signed-off-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
  comments from Alan Stern  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 3d5b6fb4 ("ACPI: Kill overly
verbose "power state" log messages") removed the actual use of this
variable, but didn't remove the variable itself, resulting in build
warnings like

  drivers/acpi/processor_idle.c: In function ‘acpi_processor_power_init’:
  drivers/acpi/processor_idle.c:1169: warning: unused variable ‘i’

Just get rid of the now unused variable.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code

But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  hrtimer: Eliminate needless reprogramming of clock events device

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: IA64=y ACPI=n build fix
  ACPI: Kill overly verbose "power state" log messages
  ACPI: fix Compaq Evo N800c (Pentium 4m) boot hang regression
  ACPI: Clarify resource conflict message
  thinkpad-acpi: fix CONFIG_THINKPAD_ACPI_HOTKEY_POLL build problem

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix hwpoison code related build failure on 32-bit NUMAQ

ia64's sim_defconfig uses CONFIG_ACPI=n
which now #define's acpi_disabled in <linux/acpi.h>

So we shouldn't re-define it here in <asm/acpi.h>
Signed-off-by: NLen Brown <len.brown@intel.com>

I was recently lucky enough to get a 64-CPU system, so my kernel log
ends up with 64 lines like:

    ACPI: CPU0 (power states: C1[C1] C2[C3])

This is pretty useless clutter because this info is already available
after boot from both /sys/devices/system/cpu/cpu*/cpuidle/state?/ as
well as /proc/acpi/processor/CPU*/power.

So just delete the code that prints the C-states in processor_idle.c.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This build failure triggers:

 In file included from include/linux/suspend.h:8,
                 from arch/x86/kernel/asm-offsets_32.c:11,
                 from arch/x86/kernel/asm-offsets.c:2:
 include/linux/mm.h:503:2: error: #error SECTIONS_WIDTH+NODES_WIDTH+ZONES_WIDTH > BITS_PER_LONG - NR_PAGEFLAGS

Because due to the hwpoison page flag we ran out of page
flags on 32-bit.

Dont turn on hwpoison on 32-bit NUMA (it's rare in any
case).

Also clean up the Kconfig dependencies in the generic MM
code by introducing ARCH_SUPPORTS_MEMORY_FAILURE.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Don't disable ARB_DISABLE when the familary ID is 0x0F.

http://bugzilla.kernel.org/show_bug.cgi?id=14211

This was a 2.6.31 regression, and so this patch
needs to be applied to 2.6.31.stable
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The message "ACPI: Device needs an ACPI driver" is misleading. The
device _may_ need an ACPI driver, if the BIOS implemented a custom
API for the device in question (which, AFAIK, can't be checked.) If
not, then either a generic ACPI driver may be used (for example
"thermal"), or nothing can be done (other than a white list).

I propose to reword the message to:

ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver

which I think is more correct. Comments and suggestions welcome.

I also added a message warning about possible problems and system
instability when users pass acpi_enforce_resources=lax, as suggested
by Len.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix this problem when CONFIG_THINKPAD_ACPI_HOTKEY_POLL is undefined:

  CHECK   drivers/platform/x86/thinkpad_acpi.c
drivers/platform/x86/thinkpad_acpi.c:1968:21: error: not an lvalue
  CC [M]  drivers/platform/x86/thinkpad_acpi.o
drivers/platform/x86/thinkpad_acpi.c: In function 'tpacpi_hotkey_driver_mask_set':
drivers/platform/x86/thinkpad_acpi.c:1968: error: lvalue required as left operand of assignment
Reported-by: NNoah Dain <noahdain@gmail.com>
Reported-by: NAudrius Kazukauskas <audrius@neutrino.lt>
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] implement ticket locks for Itanium

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  alpha: fix build after vmlinux.lds.S cleanup
  mips: fix build of vmlinux.lds

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds: move leds-clevo-mail's probe function to .devinit.text
  leds: Fix indentation in LEDS_LP3944 Kconfig entry
  leds: Fix LED names 
  leds: Fix leds-pca9532 whitespace issues
  leds: fix coding style in worker thread code for ledtrig-gpio.
  leds: gpio-leds: fix typographics fault
  leds: Add WM831x status LED driver

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
  backlight: new driver for ADP5520/ADP5501 MFD PMICs
  backlight: extend event support to also support poll()
  backlight/eeepc-laptop: Update the backlight state when we change brightness
  backlight/acpi: Update the backlight state when we change brightness
  backlight: Allow drivers to update the core, and generate events on changes
  backlight: switch to da903x driver to dev_pm_ops
  backlight: Add support for the Avionic Design Xanthos backlight device.
  backlight: spi driver for LMS283GF05 LCD
  backlight: move hp680-bl's probe function to .devinit.text
  backlight: Add support for new Apple machines.
  backlight: mbp_nvidia_bl: add support for MacBookAir 1,1
  backlight: Add WM831x backlight driver

Trivial conflicts due to '#ifdef CONFIG_PM' differences in
drivers/video/backlight/da903x_bl.c

* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
  is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: Add memory barrier commentary to futex_wait_queue_me()
  futex: Fix wakeup race by setting TASK_INTERRUPTIBLE before queue_me()
  futex: Correct futex_q woken state commentary
  futex: Make function kernel-doc commentary consistent
  futex: Correct queue_me and unqueue_me commentary
  futex: Correct futex_wait_requeue_pi() commentary

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Dont use openat()
  perf tools: Fix buffer allocation
  perf tools: .gitignore += perf*.html
  perf tools: Handle relative paths while loading module symbols
  perf tools: Fix module symbol loading bug
  perf_event, x86: Fix 'perf sched record' crashing the machine
  perf_event: Update PERF_EVENT_FORK header definition
  perf stat: Fix zero total printouts

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clocksource: Resume clocksource without taking the clocksource mutex

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  modules, tracing: Remove stale struct marker signature from module_layout()
  tracing/workqueue: Use %pf in workqueue trace events
  tracing: Fix a comment and a trivial format issue in tracepoint.h
  tracing: Fix failure path in ftrace_regex_open()
  tracing: Fix failure path in ftrace_graph_write()
  tracing: Check the return value of trace_get_user()
  tracing: Fix off-by-one in trace_get_user()

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Remove redundant non-NUMA topology functions
  x86: early_printk: Protect against using the same device twice
  x86: Reduce verbosity of "PAT enabled" kernel message
  x86: Reduce verbosity of "TSC is reliable" message
  x86: mce: Use safer ways to access MCE registers
  x86: mce, inject: Use real inject-msg in raise_local
  x86: mce: Fix thermal throttling message storm
  x86: mce: Clean up thermal throttling state tracking code
  x86: split NX setup into separate file to limit unstack-protected code
  xen: check EFER for NX before setting up GDT mapping
  x86: Cleanup linker script using new linker script macros.
  x86: Use section .data.page_aligned for the idt_table.
  x86: convert to use __HEAD and HEAD_TEXT macros.
  x86: convert compressed loader to use __HEAD and HEAD_TEXT macros.
  x86: fix fragile computation of vsyscall address

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (32 commits)
  ACPI: i2c-scmi: don't use acpi_device_uid()
  ACPI: simplify building device HID/CID list
  ACPI: remove acpi_device_uid() and related stuff
  ACPI: remove acpi_device.flags.hardware_id
  ACPI: remove acpi_device.flags.compatible_ids
  ACPI: maintain a single list of _HID and _CID IDs
  ACPI: make sure every acpi_device has an ID
  ACPI: use acpi_device_hid() when possible
  ACPI: fix synthetic HID for \_SB_
  ACPI: handle re-enumeration, when acpi_devices might already exist
  ACPI: factor out device type and status checking
  ACPI: add acpi_bus_get_status_handle()
  ACPI: use acpi_walk_namespace() to enumerate devices
  ACPI: identify device tree root by null parent pointer, not ACPI_BUS_TYPE
  ACPI: enumerate namespace before adding functional fixed hardware devices
  ACPI: convert acpi_bus_scan() to operate on an acpi_handle
  ACPI: add acpi_bus_get_parent() and remove "parent" arguments
  ACPI: remove unnecessary argument checking
  ACPI: remove redundant "type" arguments
  ACPI: remove acpi_device_set_context() "type" argument
  ...