Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 18 3月, 2013 2 次提交
  3. 06 3月, 2013 1 次提交
    • P
      drm/i915: also disable south interrupts when handling them · 44498aea
      由 Paulo Zanoni 提交于 
      From the docs:

  "IIR can queue up to two interrupt events. When the IIR is cleared,
  it will set itself again after one clock if a second event was
  stored."

  "Only the rising edge of the PCH Display interrupt will cause the
  North Display IIR (DEIIR) PCH Display Interrupt even bit to be set,
  so all PCH Display Interrupts, including back to back interrupts,
  must be cleared before a new PCH Display interrupt can cause DEIIR
  to be set".

The current code works fine because we don't get many interrupts, but
if we enable the PCH FIFO underrun interrupts we'll start getting so
many interrupts that at some point new PCH interrupts won't cause
DEIIR to be set.

The initial implementation I tried was to turn the code that checks
SDEIIR into a loop, but we can still get interrupts even after the
loop is done (and before the irq handler finishes), so we have to
either disable the interrupts or mask them. In the end I concluded
that just disabling the PCH interrupts is enough, you don't even need
the loop, so this is what this patch implements. I've tested it and it
passes the 2 "PCH FIFO underrun interrupt storms" I can reproduce:
the "ironlake_crtc_disable" case and the "wrong watermarks" case.

In other words, here's how to reproduce the problem fixed by this
patch:
  1 - Enable PCH FIFO underrun interrupts (SERR_INT on SNB+)
  2 - Boot the machine
  3 - While booting we'll get tons of PCH FIFO underrun interrupts
  4 - Plug a new monitor
  5 - Run xrandr, notice it won't detect the new monitor
  6 - Read SDEIIR and notice it's not 0 while DEIIR is 0

Q: Can't we just clear DEIIR before SDEIIR?
A: It doesn't work. SDEIIR has to be completely cleared (including the
interrupts stored on its back queue) before it can flip DEIIR's bit to
1 again, and even while you're clearing it you'll be getting more and
more interrupts.

Q: Why does it work by just disabling+enabling the south interrupts?
A: Because when we re-enable them, if there's something on the SDEIIR
register (maybe an interrupt stored on the queue), the re-enabling
will make DEIIR's bit flip to 1, and since we'll already have
interrupts enabled we'll get another interrupt, then run our irq
handler again to process the "back" interrupts.

v2: Even bigger commit message, added code comments.

Note that this fixes missed dp aux irqs which have been reported for
3.9-rc1. This regression has been introduced by switching to
irq-driven dp aux transactions with

commit 9ee32fea
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Dec 1 13:53:48 2012 +0100

    drm/i915: irq-drive the dp aux communication

References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18588.html
References: https://lkml.org/lkml/2013/2/26/769Tested-by: NImre Deak <imre.deak@intel.com>
Reported-by: NSedat Dilek <sedat.dilek@gmail.com>
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp commit message with references for the dp aux irq
timeout regression this fixes.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      44498aea
  5. 05 3月, 2013 3 次提交
  7. 21 2月, 2013 2 次提交
  9. 20 2月, 2013 3 次提交
  11. 15 2月, 2013 2 次提交
  13. 31 1月, 2013 1 次提交
  15. 22 1月, 2013 2 次提交
    • D
      drm/i915: clarify concurrent hang detect/gpu reset consistency · 7db0ba24
      由 Daniel Vetter 提交于 
      Damien Lespiau wondered how race the gpu reset/hang detection code is
against concurrent gpu resets/hang detections or combinations thereof.
Luckily the single work item is guranteed to never run concurrently,
so reset handling is already single-threaded.

Hence we only have to worry about concurrent hang detections, or a
hang detection firing off while we're still processing an older gpu
reset request. Due to the new mechanism of setting the reset in
progress flag and the ordering guaranteed by the schedule_work
function there's nothing to do but add a comment explaining why we're
safe.

The only thing I've noticed is that we still try to reset the gpu now,
even when it is declared terminally wedged. Add a check for that to
avoid continous warnings about failed resets, in case the hangcheck
timer ever gets stuck.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      7db0ba24
    • D
      drm/i915: create a race-free reset detection · f69061be
      由 Daniel Vetter 提交于 
      With the previous patch the state transition handling of the reset
code itself is now (hopefully) race free and solid. But that still
leaves out everyone else - with the various lock-free wait paths
we have there's the possibility that the reset happens between the
point where we read the seqno we should wait on and the actual wait.

And if __wait_seqno then never sees the RESET_IN_PROGRESS state, we'll
happily wait for a seqno which will in all likelyhood never signal.

In practice this is not a big problem since the X server gets
constantly interrupted, and can then submit more work (hopefully) to
unblock everyone else: As soon as a new seqno write lands, all waiters
will unblock. But running the i-g-t reset testcase ZZ_hangman can
expose this race, especially on slower hw with fewer cpu cores.

Now looking forward to ARB_robustness and friends that's not the best
possible behaviour, hence this patch adds a reset_counter to be able
to detect any reset, even if a given thread never observed the
in-progress state.

The important part is to correctly order things:
- The write side needs to increment the counter after any seqno gets
  reset.  Hence we need to do that at the end of the reset work, and
  again wake everyone up. We also need to place a barrier in between
  any possible seqno changes and the counter increment, since any
  unlock operations only guarantee that nothing leaks out, but not
  that at later load operation gets moved ahead.
- On the read side we need to ensure that no reset can sneak in and
  invalidate the seqno. In all cases we can use the one-sided barrier
  that unlock operations guarantee (of the lock protecting the
  respective seqno/ring pair) to ensure correct ordering. Hence it is
  sufficient to place the atomic read before the mutex/spin_unlock and
  no additional barriers are required.

The end-result of all this is that we need to wake up everyone twice
in a reset operation:
- First, before the reset starts, to get any lockholders of the locks,
  so that the reset can proceed.
- Second, after the reset is completed, to allow waiters to properly
  and reliably detect the reset condition and bail out.

I admit that this entire reset_counter thing smells a bit like
overkill, but I think it's justified since it makes it really explicit
what the bail-out condition is. And we need a reset counter anyway to
implement ARB_robustness, and imo with finer-grained locking on the
horizont this is the most resilient scheme I could think of.

v2: Drop spurious change in the wait_for_error EXIT_COND - we only
need to wait until we leave the reset-in-progress wedged state.

v3: Don't play tricks with barriers in the throttle ioctl, the
spin_unlock is barrier enough.

I've also considered using a little helper to grab the current
reset_counter, but then decided that hiding the atomic_read isn't a
great idea, since having it explicitly show up in the code is a nice
remainder to reviews to check the memory barriers.

v4: Add a comment to explain why we need to fall through in
__wait_seqno in the end variable assignments.

v5: Review from Damien:
- s/smb/smp/ in a comment
- don't increment the reset counter after we've set it to WEDGED. Now
  we (again) properly wedge the gpu when the reset fails.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      f69061be
  17. 20 1月, 2013 3 次提交
    • D
      drm/i915: clear up wedged transitions · 1f83fee0
      由 Daniel Vetter 提交于 
      We have two important transitions of the wedged state in the current
code:

- 0 -> 1: This means a hang has been detected, and signals to everyone
  that they please get of any locks, so that the reset work item can
  do its job.

- 1 -> 0: The reset handler has completed.

Now the last transition mixes up two states: "Reset completed and
successful" and "Reset failed". To distinguish these two we do some
tricks with the reset completion, but I simply could not convince
myself that this doesn't race under odd circumstances.

Hence split this up, and add a new terminal state indicating that the
hw is gone for good.

Also add explicit #defines for both states, update comments.

v2: Split out the reset handling bugfix for the throttle ioctl.

v3: s/tmp/wedged/ sugested by Chris Wilson. Also fixup up a rebase
error which prevented this patch from actually compiling.

v4: To unify the wedged state with the reset counter, keep the
reset-in-progress state just as a flag. The terminally-wedged state is
now denoted with a big number.

v5: Add a comment to the reset_counter special values explaining that
WEDGED & RESET_IN_PROGRESS needs to be true for the code to be
correct.

v6: Fixup logic errors introduced with the wedged+reset_counter
unification. Since WEDGED implies reset-in-progress (in a way we're
terminally stuck in the dead-but-reset-not-completed state), we need
ensure that we check for this everywhere. The specific bug was in
wait_for_error, which would simply have timed out.

v7: Extract an inline i915_reset_in_progress helper to make the code
more readable. Also annote the reset-in-progress case with an
unlikely, to help the compiler optimize the fastpath. Do the same for
the terminally wedged case with i915_terminally_wedged.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      1f83fee0
    • D
      drm/i915: move wedged to the other gpu error handling stuff · 33196ded
      由 Daniel Vetter 提交于 
      And to make Ben Widawsky happier, use the gpu_error instead of
the entire device as the argument in some functions.

Drop the outdated comment on ->wedged for now, a follow-up patch will
change the semantics and add a proper comment again.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      33196ded
    • D
      drm/i915: extract hangcheck/reset/error_state state into substruct · 99584db3
      由 Daniel Vetter 提交于 
      This has been sprinkled all over the place in dev_priv. I think
it'd be good to also move all the code into a separate file like
i915_gem_error.c, but that's for another patch.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      99584db3
  19. 18 1月, 2013 2 次提交
  21. 15 1月, 2013 1 次提交
  23. 19 12月, 2012 1 次提交
  25. 18 12月, 2012 1 次提交
    • D
      drm/i915: Implement workaround for broken CS tlb on i830/845 · b45305fc
      由 Daniel Vetter 提交于 
      Now that Chris Wilson demonstrated that the key for stability on early
gen 2 is to simple _never_ exchange the physical backing storage of
batch buffers I've tried a stab at a kernel solution. Doesn't look too
nefarious imho, now that I don't try to be too clever for my own good
any more.

v2: After discussing the various techniques, we've decided to always blit
batches on the suspect devices, but allow userspace to opt out of the
kernel workaround assume full responsibility for providing coherent
batches. The principal reason is that avoiding the blit does improve
performance in a few key microbenchmarks and also in cairo-trace
replays.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet:
- Drop the hunk which uses HAS_BROKEN_CS_TLB to implement the ring
  wrap w/a. Suggested by Chris Wilson.
- Also add the ACTHD check from Chris Wilson for the error state
  dumping, so that we still catch batches when userspace opts out of
  the w/a.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      b45305fc
  27. 12 12月, 2012 1 次提交
    • D
      drm/i915: Fixup hpd irq register setup ordering · 20afbda2
      由 Daniel Vetter 提交于 
      For GMCH platforms we set up the hpd irq registers in the irq
postinstall hook. But since we only enable the irq sources we actually
need in PORT_HOTPLUG_EN/STATUS, taking dev_priv->hotplug_supported_mask
into account, no hpd interrupt sources is enabled since

commit 52d7eced
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Dec 1 21:03:22 2012 +0100

    drm/i915: reorder setup sequence to have irqs for output setup

Wrongly set-up interrupts also lead to broken hw-based load-detection
on at least GM45, resulting in ghost VGA/TV-out outputs.

To fix this, delay the hotplug register setup until after all outputs
are set up, by moving it into a new dev_priv->display.hpd_irq_callback.
We might also move the PCH_SPLIT platforms to such a setup eventually.

Another funny part is that we need to delay the fbdev initial config
probing until after the hpd regs are setup, for otherwise it'll detect
ghost outputs. But we can only enable the hpd interrupt handling
itself (and the output polling) _after_ that initial scan, due to
massive locking brain-damage in the fbdev setup code. Add a big
comment to explain this cute little dragon lair.

v2: Encapsulate all the fbdev handling by wrapping the move call into
intel_fbdev_initial_config in intel_fb.c. Requested by Chris Wilson.

v3: Applied bikeshed from Jesse Barnes.

v4: Imre Deak noticed that we also need to call intel_hpd_init after
the drm_irqinstall calls in the gpu reset and resume paths - otherwise
hotplug will be broken. Also improve the comment a bit about why
hpd_init needs to be called before we set up the initial fbdev config.

Bugzilla: Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54943Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      20afbda2
  29. 09 12月, 2012 1 次提交
  31. 06 12月, 2012 10 次提交
    • C
      drm/i915: Close race between processing unpin task and queueing the flip · e7d841ca
      由 Chris Wilson 提交于 
      Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.

To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.

v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      e7d841ca
    • P
      drm/i915: be less verbose when handling gmbus/aux irqs · 36dacf5b
      由 Paulo Zanoni 提交于 
      Having 9500 lines repeated on dmesg does not help me at all.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      36dacf5b
    • D
      drm/i915: irq-drive the dp aux communication · 9ee32fea
      由 Daniel Vetter 提交于 
      At least on the platforms that have a dp aux irq and also have it
enabled - vlvhsw should have one, too. But I don't have a machine to
test this on. Judging from docs there's no dp aux interrupt for gm45.

Also, I only have an ivb cpu edp machine, so the dp aux A code for
snb/ilk is untested.

For dpcd probing when nothing is connected it slashes about 5ms of cpu
time (cpu time is now negligible), which agrees with 3 * 5 400 usec
timeouts.

A previous version of this patch increases the time required to go
through the dp_detect cycle (which includes reading the edid) from
around 33 ms to around 40 ms. Experiments indicated that this is
purely due to the irq latency - the hw doesn't allow us to queue up
dp aux transactions and hence irq latency directly affects throughput.
gmbus is much better, there we have a 8 byte buffer, and we get the
irq once another 4 bytes can be queued up.

But by using the pm_qos interface to request the lowest possible cpu
wake-up latency this slowdown completely disappeared.

Since all our output detection logic is single-threaded with the
mode_config mutex right now anyway, I've decide not ot play fancy and
to just reuse the gmbus wait queue. But this would definitely prep the
way to run dp detection on different ports in parallel

v2: Add a timeout for dp aux transfers when using interrupts - the hw
_does_  prevent this with the hw-based 400 usec timeout, but if the
irq somehow doesn't arrive we're screwed. Lesson learned while
developing this ;-)

v3: While at it also convert the busy-loop to wait_for_atomic, so that
we don't run the risk of an infinite loop any more.

v4: Ensure we have the smallest possible irq latency by using the
pm_qos interface.

v5: Add a comment to the code to explain why we frob pm_qos. Suggested
by Chris Wilson.

v6: Disable dp irq for vlv, that's easier than trying to get at docs
and hw.

v7: Squash in a fix for Haswell that Paulo Zanoni tracked down - the
dp aux registers aren't at a fixed offset any more, but can be on the
PCH while the DP port is on the cpu die.

Reviewed-by: Imre Deak <imre.deak@intel.com> (v6)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      9ee32fea
    • D
      drm/i915: wire up do aux channel done interrupt · ce99c256
      由 Daniel Vetter 提交于 
      Doesn't do anything yet than call dp_aux_irq_handler.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      ce99c256
    • D
      drm/i915: use the gmbus irq for waits · 28c70f16
      由 Daniel Vetter 提交于 
      We need two special things to properly wire this up:
- Add another argument to gmbus_wait_hw_status to pass in the
  correct interrupt bit in gmbus4.
- Since we can only get an irq for one of the two events we want,
  hand-roll the wait_event_timeout code so that we wake up every
  jiffie and can check for NAKs. This way we also subsume gmbus
  support for platforms without interrupts (or where those are not
  yet enabled).

The important bit really is to only enable one gmbus interrupt source
at the same time - with that piece of lore figured out, this seems to
work flawlessly.

Ben Widawsky rightfully complained the lack of measurements for the
claimed benefits (especially since the first version was actually
broken and fell back to bit-banging). Previously reading the 256 byte
hdmi EDID takes about 72 ms here. With this patch it's down to 33 ms.
Given that transfering the 256 bytes over i2c at wire speed takes
20.5ms alone, the reduction in additional overhead is rather nice.

v2: Chris Wilson wondered whether GMBUS4 might contain some set bits
when booting up an hence result in some spurious interrupts. Since we
clear GMBUS4 after every wait and we do gmbus transfer really early in
the setup sequence to detect displays the window is small, but still
be paranoid and clear it properly.

v3: Clarify the comment that gmbus irq generation can only support one
kind of event, why it bothers us and how we work around that limit.

Cc: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      28c70f16
    • D
      drm/i915: wire up gmbus irq handler · 515ac2bb
      由 Daniel Vetter 提交于 
      Only enables the interrupt and puts a irq handler into place, doesn't
do anything yet.

Unfortunately there's no gmbus interrupt support for gen2/3 (safe for
pnv, but there the irq is marked as "Test mode").

v2: Wire up the irq handler for vlv and gen4 properly.

v3: i915_enable_pipestat expects the mask bit, not the status bits ... and
for added hilarity those are rather inconsistently named.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      515ac2bb
    • D
      drm/i915: reorder setup sequence to have irqs for output setup · 52d7eced
      由 Daniel Vetter 提交于 
      Otherwise the new&shiny irq-driven gmbus and dp aux code won't work that
well. Noticed since the dp aux code doesn't have an automatic fallback
with a timeout (since the hw provides for that already).

v2: Simple move drm_irq_install before intel_modeset_gem_init, as
suggested by Ben Widawsky.

v3: Now that interrupts are enabled before all connectors are fully
set up, we might fall over serving a HPD interrupt while things are
still being set up. Instead of jumping through massive hoops and
complicating the code with a separate hpd irq enable step, simply
block out the hotplug work item from doing anything until things are
in place.

v4: Actually, we can enable hotplug processing only after the fbdev is
fully set up, since we call down into the fbdev from the hotplug work
functions. So stick the hpd enabling right next to the poll helper
initialization.

v5: We need to enable irqs before intel_modeset_init, since that
function sets up the outputs.

v6: Fixup cleanup sequence, too.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      52d7eced
    • D
      drm/i915: setup the hangcheck timer early · 61bac78e
      由 Daniel Vetter 提交于 
      ... together with all the other irq related resources in
intel_irq_init. I've managed to oops in the notify_ring function on my
ilk, presumably because of the powerctx setup call to i915_gpu_idle.

Note that this is only a problem with the reorder irq setup sequence
for irq-driver gmbus/dp aux.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      61bac78e
    • D
      drm/i915: don't handle PIPE_LEGACY_BLC_EVENT_STATUS on vlv · d83779a9
      由 Daniel Vetter 提交于 
      This is for legacy legacy stuff, and checking with the leftover
pipe from the previous loop is propably not what we want. Since
pipe == 2 after the loop ... Then we only assing a variable and do
nothing with it.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      d83779a9
    • D
      drm/i915: haswell has the same irq handlers as ivb · 4a06e201
      由 Daniel Vetter 提交于 
      No need to have the exaxt same code twice.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      4a06e201
  33. 04 12月, 2012 1 次提交
    • D
      drm/i915: fixup sparse warnings · 1a240d4d
      由 Daniel Vetter 提交于 
      - __iomem where there is none (I love how we mix these things up).
- Use gfp_t instead of an other plain type.
- Unconfuse one place about enum pipe vs enum transcoder - for the pch
  transcoder we actually use the pipe enum. Fixup the other cases
  where we assign the pipe to the cpu transcoder with explicit casts.
- Declare the mch_lock properly in a header.

There is still a decent mess in intel_bios.c about __iomem, but heck,
this is x86 and we're allowed to do that.

Makes-sparse-happy: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use a space after the cast consistently and fix up the
newly-added cast in i915_irq.c to properly use __iomem.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
      1a240d4d
  35. 01 12月, 2012 2 次提交
  37. 29 11月, 2012 1 次提交