Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.

The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth.  If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth.  While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.

This patch implements an "off switch" as a module parameter.
Signed-off-by: NMichael Reed <mdr@sgi.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Information present in static table is only valid for pre-ISP25xx
adapters.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the number of request queues to the module paramater
ql2xmaxqueues.  Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process.  The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):

    drivers/char/random.c: In function `get_random_int':
    drivers/char/random.c:1672: error: unrecognizable insn:
    (insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
            (subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
                        (subreg:DI (reg:SI 6 bp) 0))
                    (const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
        (nil))
    drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083

and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.

This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.

So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: NMartin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In Commit

commit 3b8b5c9b
Author: Eric Moore <eric.moore@lsi.com>
Date:   Tue Apr 21 15:44:27 2009 -0600

    [SCSI] mpt2sas : bump driver version to 01.100.02.00
 
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00.  Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: NEric Moore <eric.moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.

That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).

The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().

Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.

Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Tested-by: NDaniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Reported-by: NJonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c107 (ide: add struct ide_host
(take 3)).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Impact: fix an oops which always triggers

ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack.  Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Processor idle power states C2 and C3 stop the TSC on many machines.
Linux recognizes this situation and marks the TSC as unstable:

Marking TSC unstable due to TSC halts in idle

But if those same machines are booted with "processor.max_cstate=1",
then there is no need to validate C2 and C3, and no need to
disable the TSC, which can be reliably used as a clocksource.
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>

A previous 2.6.30 patch, a71e4917,
(ACPI: idle: mark_tsc_unstable() at init-time, not run-time)
erroneously disabled the TSC on systems that did not actually
have valid deep C-states.

Move the check after the deep-C-states are validated,
via new helper, tsc_check_state(), hich replaces tsc_halts_in_c().
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NFrans Pop <elendil@planet.nl>

If the BIOS hands us an invalid throttling state,
write a valid state.

http://bugzilla.kernel.org/show_bug.cgi?id=13259Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NJames Ettle <theholyettlz@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Introduce module parameter processor.ignore_tpc.

Some laptops are shipped with buggy _TPC,
this module parameter is used to to disable the buggy support.

http://bugzilla.kernel.org/show_bug.cgi?id=13259Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NJames Ettle <theholyettlz@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'

http://bugzilla.kernel.org/show_bug.cgi?id=13165Signed-off-by: NLen Brown <len.brown@intel.com>

In 2.6.29,
31878dd8
"ACPI: remove BM_RLD access from idle entry path"
moved BM_RLD initialization to init-time from run time.

But we discovered that some BIOS do not restore BM_RLD
after suspend, causing device errors on C3 and C4
after resume.  So now the kernel restores BM_RLD.

http://bugzilla.kernel.org/show_bug.cgi?id=13032Signed-off-by: NLen Brown <len.brown@intel.com>

The BIOS bug workaround mistakenly got disabled
when we followed the ACPI specification more closely
by ignoring OS updates to that bit.

(The BIOS is supposed to update SCI_EN, not the OS)

http://bugzilla.kernel.org/show_bug.cgi?id=13289Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.

The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard.  Only then are the
characteristics reported to SCSI via the VPD B1 page.

This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever.  With no complaints so far.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.

This patch is based upon code from Matthew Wilcox' 4KB ATA tree.  I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'.  This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We we build with dma_addr_t as a 64-bit quantity we get:

drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Issuing ATA_CMD_SET_FEATURES (0xef) times out because
pdc20621_interrupt ignores command completion since
ATA_TFLAG_POLLING flag is set.

This has already been fixed for sata_promise:

commit 51b94d2a
Author: Tejun Heo <htejun@gmail.com>
Date:   Fri Jun 8 13:46:55 2007 -0700

    sata_promise: use TF interface for polling NODATA commands

Also, this patch includes Mikael's original patches:

http://marc.info/?l=linux-ide&m=121135828227724&w=2
http://marc.info/?l=linux-ide&m=121144512109826&w=2Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :

WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch fixes the following regression the occurred during the
scsi_dma_map()/unmap() changes:

3w-9xxx 0001:45:00.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We use the name provided by SES to name objects.  An empty name is
legal in SES but causes problems in our generic device hierarchy.  Fix
this by falling back to a number if the name is either NULL or empty.

Also fix a secondary bug spotted in that dev_set_name(dev, name) uses
a string format and so would go wrong if name contained a '%'.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Andrew Vasquez wrote:
> fc-transport: Close state transition-window during rport deletion.
>
> After an rport's state has transitioned to FC_PORTSTATE_BLOCKED,
> but, prior to making the upcall to 'block' the scsi-target
> associated with an rport, queued commands can recycle and
> ultimately run out of retries causing failures to propagate to
> upper-level drivers.  Close this transition-window by returning
> the non-'retries' modifying DID_IMM_RETRY status for submitted
> I/Os.

The same can happen for iscsi when transitioning from logged in
to failed and blocking the sdevs.

This patch converts iscsi and fc's transitions back to use DID_IMM_RETRY
instead of DID_TRANSPORT_DISRUPTED which has a limited number of retries
that we do not want to use for handling this race.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
[Addition of iscsi and fc port online devloss case conversion by Mike Christie]
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Commit 79e53945 introduced a
regression where you cannot use sysrq 'g' to enter kgdb.  The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics.  The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.

This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

The receive interrupt routine checks the wrong register if the
receive fifo is empty. Further an explicit interrupt acknowledge
write is introduced. In some circumstances another interrupt was
issued.
Signed-off-by: NBenjamin Krill <ben@codiert.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC.  Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: NCarl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: NEric Anholt <eric@anholt.net>

We detect HDMI output connection status by writing to HOT Plug Interrupt
Detect Enable bit in PORT_HOTPLUG_EN.  The behavior will generate a specified
interrupt, which is caught by audio driver, but during one detection driver
set all Detect Enable bits of HDMIB, HDMIC HDMID, and generate wrong
interrupt signals for current output, according to the signals audio driver
misunderstand device status. The patch intends to handle corresponding
output precisely.

It fixed freedesktop.org bug #21371
Signed-off-by: NMa Ling <ling.ma@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>