* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (lm85) extend to support EMC6D103 chips
  MAINTAINERS: Remove stale hwmon quilt tree
  hwmon: (k10temp) add support for AMD Family 12h/14h CPUs
  hwmon: (jc42) do not allow writing to locked registers
  hwmon: (jc42) more helpful documentation
  hwmon: (jc42) fix type mismatch

This reverts commit 9b29050f.

It has caused hibernate regressions, for example Juri Sladby's report:

  "I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
   [10974.074587] Suspending console(s) (use no_console_suspend to debug)
   [10974.103073] tpm_tis 00:0c: Operation Timed out
   [10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
   [10974.103095] PM: Device 00:0c failed to freeze: error -62"

and Rafael points out that some of the new conditionals in that commit
seem to make no sense.  This commit needs more work and testing, let's
revert it for now.
Reported-by: NNorbert Preining <preining@logic.at>
Reported-and-requested-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change my email address to my main account.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.

Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org

* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  RTC: Re-enable UIE timer/polling emulation
  RTC: Revert UIE emulation removal
  RTC: Release mutex in error path of rtc_alarm_irq_enable

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
  net: deinit automatic LIST_HEAD
  net: dont leave active on stack LIST_HEAD
  net: provide default_advmss() methods to blackhole dst_ops
  tg3: Restrict phy ioctl access
  drivers/net: Call netif_carrier_off at the end of the probe
  ixgbe: work around for DDP last buffer size
  ixgbe: fix panic due to uninitialised pointer
  e1000e: flush all writebacks before unload
  e1000e: check down flag in tasks
  isdn: hisax: Use l2headersize() instead of dup (and buggy) func.
  arp_notify: unconditionally send gratuitous ARP for NETDEV_NOTIFY_PEERS.
  cxgb4vf: Use defined Mailbox Timeout
  cxgb4vf: Quiesce Virtual Interfaces on shutdown ...
  cxgb4vf: Behave properly when CONFIG_DEBUG_FS isn't defined ...
  cxgb4vf: Check driver parameters in the right place ...
  pch_gbe: Fix the MAC Address load issue.
  iwlwifi: Delete iwl3945_good_plcp_health.
  net/can/softing: make CAN_SOFTING_CS depend on CAN_SOFTING
  netfilter: nf_iterate: fix incorrect RCU usage
  pch_gbe: Fix the issue that the receiving data is not normal.
  ...

* 'for-linus/bugfixes' of git://xenbits.xen.org/people/ianc/linux-2.6:
  xen: suspend and resume system devices when running PVHVM

* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
  workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
  workqueue: wake up a worker when a rescuer is leaving a gcwq

commit 9b5e383c (net: Introduce
unregister_netdevice_many()) left an active LIST_HEAD() in
rollback_registered(), with possible memory corruption.

Even if device is freed without touching its unreg_list (and therefore
touching the previous memory location holding LISTE_HEAD(single), better
close the bug for good, since its really subtle.

(Same fix for default_device_exit_batch() for completeness)
Reported-by: NMichal Hocko <mhocko@suse.cz>
Tested-by: NMichal Hocko <mhocko@suse.cz>
Reported-by: NEric W. Biderman <ebiderman@xmission.com>
Tested-by: NEric W. Biderman <ebiderman@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
CC: stable <stable@kernel.org> [.33+]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric W. Biderman and Michal Hocko reported various memory corruptions
that we suspected to be related to a LIST head located on stack, that
was manipulated after thread left function frame (and eventually exited,
so its stack was freed and reused).

Eric Dumazet suggested the problem was probably coming from commit
44345724 (net: factorize
sync-rcu call in unregister_netdevice_many)

This patch fixes __dev_close() and dev_close() to properly deinit their
respective LIST_HEAD(single) before exiting.

References: https://lkml.org/lkml/2011/2/16/304
References: https://lkml.org/lkml/2011/2/14/223Reported-by: NMichal Hocko <mhocko@suse.cz>
Tested-by: NMichal Hocko <mhocko@suse.cz>
Reported-by: NEric W. Biderman <ebiderman@xmission.com>
Tested-by: NEric W. Biderman <ebiderman@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0dbaee3b (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: NGeorge Spelvin <linux@horizon.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When list debugging is enabled, we aim to readably show list corruption
errors, and the basic list_add/list_del operations end up having extra
debugging code in them to do some basic validation of the list entries.

However, "list_del_init()" and "list_move[_tail]()" ended up avoiding
the debug code due to how they were written. This fixes that.

So the _next_ time we have list_move() problems with stale list entries,
we'll hopefully have an easier time finding them..
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ftp://pub.kernel.org/pub/linux/kernel/people/groeck/linux-staging/
is not kept up to date, so remove reference to it.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828c: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Hibernate: Return error code when alloc_image_page() fails

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: add missing frac fb div flag for dce4+
  drm/radeon/kms: do not reject X16 and Y16X16 floating-point formats on r300
  drm/nouveau: fix suspend/resume on GPUs that don't have PM support
  drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
  drm/nv40: fix tiling-related setup for a number of chipsets
  drm/nouveau: fix non-EDIDful native mode selection
  drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
  drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
  drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/qib: Prevent double completions after a timeout or RNR error
  IB/qib: Fix double add_timer()
  RDMA/nes: Don't generate async events for unregistered devices

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix NMI startup bug which also breaks perf.
  sparc: fix size argument to find_next_zero_bit()
  sparc: use bitmap_set()
  sparc32: unaligned memory access (MNA) trap handler bug

Validate number of blocks in map and remove redundant variable.
Signed-off-by: NTimo Warns <warns@pre-sense.de>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch re-enables UIE timer/polling emulation for rtc devices
that do not support alarm irqs.

CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.

This patch reverts the following commits:
042620a0 - Remove UIE emulation
1daeddd5 - Cleanup removed UIE emulation declaration
b5cc8ca1 - Remove Kconfig symbol for UIE emulation

The emulation mode will still need to be wired-in with a following
patch before it will work.

CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

On hardware that doesn't support alarm interrupts, rtc_alarm_irq_enable
could return without releasing the ops_lock mutex.

This was introduced in
	aa0be0f4 (RTC: Propagate error handling via rtc_timer_enqueue properly)

This patch corrects the issue by only returning once the mutex is
released.

[john.stultz: Reworded the commit log]
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

If management firmware is present and the device is down, the firmware
will assume control of the phy.  If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior.  This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).

This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a double completion associated with error handling for RC QPs.

The sequence is:

 - The do_rc_ack() routine fields an RNR nack and there are 0
   rnr_retries configured on the QP.
 - qib_error_qp() stops the pending timer
 - qib_rc_send_complete() is called from sdma_complete()
 - qib_rc_send_complete() starts the timer because the msb of the psn
   just completed says an ack is needed.
 - a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
 - rc_timeout() calls qib_restart_rc()
 - qib_restart_rc() calls qib_send_complete() with a
   IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
   past

The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Otherwise we fail to properly suspend/resume all of the emulated devices.

Something between 2.6.38-rc2 and rc3 appears to have exposed this
issue, but it's always been wrong not to do this.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NJeremy Fitzhardinge <jeremy@goop.org>

A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: NAmir Hanania <amir.hanania@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Systems containing an 82599EB and running a backported driver from
upstream were panicing on boot.  It turns out hw->mac.ops.setup_sfp is
only set for 82599, so one should check to be sure that pointer is set
before continuing in ixgbe_sfp_config_module_task.  I verified by
inspection that the upstream driver has the same issue and also added a
check before the call in ixgbe_sfp_link_config.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was not flushing all writebacks before unloading, possibly
causing memory to be written by the hardware after the driver had
reinitialized the rings.

This adds missing functionality to flush any pending writebacks and is
called in all spots where descriptors should be completed before the driver
begins processing.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is part of a fix to avoid any tasks running while the driver is
exiting and deinitializing resources.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux:
  nfsd: correctly handle return value from nfsd_map_name_to_*

* 'nouveau/drm-nouveau-next' of /ssd/git/drm-nouveau-next:
  drm/nouveau: fix suspend/resume on GPUs that don't have PM support
  drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
  drm/nv40: fix tiling-related setup for a number of chipsets
  drm/nouveau: fix non-EDIDful native mode selection
  drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
  drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
  drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.

The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+.  Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This has been broken since 2.6.37, and fixes resume on a couple of fermi
boards I have access to.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi/pxa2xx pci: fix the release - remove race

This reverts commit 75f1dc0d ("block: check bdev_read_only() from
blkdev_get()").  That commit added stricter checking to make sure
devices that were being used read-only were actually opened in that
mode.

It turns out that the change breaks a bunch of kernel code that opens
block devices.  Affected systems include dm, md, and the loop device.
Because strict checking for read-only opens of block devices was not
done before this, the code that opens the devices was opening them
read-write even if they were being used read-only.  Auditing all that
code will take time, and new userspace packages for dm, mdadm, etc.
will also be required.
Signed-off-by: NChuck Ebbert <cebbert@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We free the temporary binding before leaving this function, so we also have
to wait for the move to actually complete.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Due to the default case handling the older chipsets, a bunch of the newer
ones ended up having the wrong tiling regs used.  This commit switches the
default case to handle the newest chipsets.

This also makes nv4e touch the "extra" tiling regs.  "nv" doesn't touch
them for C51 but traces of the NVIDIA binary driver show it being done
there.

I couldn't find NV41/NV45 traces to confirm the behaviour there, but an
educated guess was taken at each of them.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>