When NAT is built as a module, ip_conntrack_netlink can not be linked
statically.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

default_rrq_ttl is used when no TTL is included in the RRQ.
Signed-off-by: NJing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move prototypes of NAT callbacks to ip_conntrack_h323.h. Because the
use of typedefs as arguments, some header files need to be moved as
well.
Signed-off-by: NJing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix section mismatch warnings caused by netfilter's init_or_cleanup
functions used in many places by splitting the init from the cleanup
parts.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up hook registration by makeing use of the new mass registration and
unregistration helpers.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables support for the Sigmatel's STIR421x IrDA chip.
Once patched with Sigmatel's firmware, this chip "almost" follows the
USB-IrDA spec. Thus this patch is against irda-usb.[ch].

The code has been tested by Nick Fedchik on an STIR4210 chipset based
dongle.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch integrates the smcinit code into the smsc-ircc driver.
Some laptops have their smsc-ircc chip not properly configured by the
BIOS and needs some preconfiguration. Currently, this can be done from
userspace with smcinit, a utility that comes with the irda-utils
package. It messes with ioports and PCI settings, from userspace.  Now
with this patch, if we happen to be on one of the known to be faulty
laptops, we preconfigure the chip from the driver.

Patch from Linus Walleij <triad@df.lth.se>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes GRE and SIT to generate port unreachable instead of
protocol unreachable errors when we can't find a matching tunnel for a
packet.

This removes the ambiguity as to whether the error is caused by no
tunnel being found or by the lack of support for the given tunnel
type.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this fixes coverity bug id #1068.
hci_send_sco() frees skb if (skb->len > hdev->sco_mtu).
Since it returns a negative error value only in this case, we
can directly return here.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a memory leak (buf wasn't freed) spotted by the
Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an off-by-21-or-49 error ;-) spotted by the Coverity
checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set .name in netconsole's struct console to identify the
struct's owner.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the sending of ICMP messages when there are no IPv4/IPv6
tunnels present to tunnel4/tunnel6 respectively.  Please note that for now
if xfrm4_tunnel/xfrm6_tunnel is loaded then no ICMP messages will ever be
sent.  This is similar to how we handle AH/ESP/IPCOMP.

This move fixes the bug where we always send an ICMP message when there is
no ip6_tunnel device present for a given packet even if it is later handled
by IPsec.  It also causes ICMP messages to be sent when no IPIP tunnel is
present.

I've decided to use the "port unreachable" ICMP message over the current
value of "address unreachable" (and "protocol unreachable" by GRE) because
it is not ambiguous unlike the other ones which can be triggered by other
conditions.  There seems to be no standard specifying what value must be
used so this change should be OK.  In fact we should change GRE to use
this value as well.

Incidentally, this patch also fixes a fairly serious bug in xfrm6_tunnel
where we don't check whether the embedded IPv6 header is present before
dereferencing it for the inside source address.

This patch is inspired by a previous patch by Hugo Santos <hsantos@av.it.pt>.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conntrack code doesn't do re-fragmentation of defragmented packets
anymore but relies on fragmentation in the IP layer. Purely bridged
packets don't pass through the IP layer, so the bridge netfilter code
needs to take care of fragmentation itself.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seems like leaf (end-nodes) has been freed by __tnode_free_rcu and not
by __leaf_free_rcu. This fixes the problem. Only tnode_free is now
used which checks for appropriate node type. free_leaf can be removed.
Signed-off-by: NRobert Olsson <robert.olsson@its.uu.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to dereference x->encap before dereferencing it for encap_type.
If it's absent then the encap_type is zero.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

    security/selinux/xfrm.c: In function 'selinux_socket_getpeer_dgram':
    security/selinux/xfrm.c:284: error: 'struct sec_path' has no member named 'x'
    security/selinux/xfrm.c: In function 'selinux_xfrm_sock_rcv_skb':
    security/selinux/xfrm.c:317: error: 'struct sec_path' has no member named 'x'
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This effectively undoes the PCI resource allocation changes done in
commit b408cbc7, but leaves the cleanups
of that commit in place.

We're going back to marking the resources reported by e820 busy _before_
doing PCI probing, so that any PCI resource that clashes with the BIOS-
reported memory map will be reloacted to a non-clashing area.

The reason? Larry Finger reports that his laptop has the cardbus
controller set up by the BIOS so that it conflicts with the e820 memory
map, and needs to be relocated. See

   http://bugzilla.kernel.org/show_bug.cgi?id=6337

for more details.

We'll have to work out how to handle the fbcon problem that caused that
commit in the first place in some other way.

Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: <bjk@luxsci.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Or rather compute it based on the table length automatically.

This also has the intended side effect of not warning for new system calls
anymore.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix CONFIG_REORDER.

The value of cflags-y was assined to CFLAGS before cflags-y was assigned
the value used for CONFIG_REORDER.

Use cflags-y for all CFLAGS options in the Makefile to avoid this
happening again.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In linux-2.6.16, we have noticed a problem where the gs base value
returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if:

   - the current/calling task has NOT set its own gs base yet to a
     non-zero value,

   - some other task that ran on the same processor previously set their
     own gs base to a non-zero value.

In this situation, the ARCH_GET_GS code will read and return the
MSR_KERNEL_GS_BASE msr register.

However, since the __switch_to() code does NOT load/zero the
MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero
next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back
the value of some previous tasks's gs base value instead of 0.

    Change the arch_prctl() ARCH_GET_GS code to only read and return
    the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling
    task is non-zero.

    Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...),
    a task can also setup a gs base value by using modify_ldt() and write
    an index value into 'gs' from user space, the patch below reads
    'gs' instead of using thread.gs, since in the modify_ldt() case,
    the thread.gs value will be 0, and incorrect value would be returned
    (the task->thread.gs value).

    When the user has not set its own gs base value and the 'gs'
    register is zero, then the MSR_KERNEL_GS_BASE register will not be
    read and a value of zero will be returned by reading and returning
    'task->thread.gs'.

    The first patch shown below is an attempt at implementing this
    approach.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Printk doesn't have any value
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).

If HZ changes, this drift can become even more pronounced.

HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.

Vojtech comments:

  "It's not entirely correct (it assumes the HPET ticks totally
   exactly), but it's significantly better than assuming the PIT error
   there."
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Mostly to get better handling when a extended config space
access has to fallback to Type1.

Cc: gregkh@suse.de
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Previously only the first bus would be checked against Type 1.

Why 16? Checking all would need too much memory and we
can assume that systems with more than 16 busses have better than
average quality BIOS.

This is an additional defense against bad MCFG tables.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixup the read mostly section to start at internode cacheline boundary.
Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: NShai Fultheim <shai@scalex86.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix

  WARNING: vmlinux: 'strlen' exported twice. Previous export was in vmlinux

Reported by Mats Johannesson
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Intel EM64T CPUs handle uncanonical return addresses differently
from AMD CPUs.

The exception is reported in the SYSRET, not the next instruction.
This leads to the kernel exception handler running on the user stack
with the wrong GS because the kernel didn't expect exceptions
on this instruction.

This version of the patch has the teething problems that plagued an earlier
version fixed.

This is CVE-2006-0744

Thanks to Ernie Petrides and Asit B. Mallick for analysis and initial
patches.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Machine checks can stall the machine for a long time and
it's not good to trigger the nmi watchdog during that.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The generic linux/numa.h file defines NODES_SHIFT to 0 in case
the architecture did not.

Every architecture which has a NUMA config option defines
NODES_SHIFT in its asm-$ARCH headers, but only if NUMA is
enabled, except for x86_64.

This should make it like all the rest.
Signed-off-by: NDave Hansen <haveblue@us.ibm.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This prevents crashes on dual core system when enough ticks are lost.

Replaces earlier patch by me.

Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

AMD systems have a modern APIC that supports 8 bit IDs, but
don't have a XAPIC version number.  Add a new "modern_apic"
subfunction that handles this correctly and use it (nearly)
everywhere where XAPIC is tested for.

I removed one wart: the code specified that external APICs
would use an 8bit APIC ID. But I checked a real 82093 data sheet
and it says clearly that they only use 4bit. So I removed
this special case since it would a bit awkward to implement now.

I removed the valid APIC tests in mptable parsing completely. On any modern
system they only check against the full field width (8bit) anyways
and are no-ops. This also fixes them doing the wrong thing
on >8 core Opterons.

This makes i386 boot again on 16 core Opterons.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Needed for other checks later in ACPI.

Pointed out by Len Brown
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When nolapic was passed or the local APIC was disabled
for another reason ACPI would still parse the IO-APICs
until these were explicitely disabled with noapic.

Usually this resulted in a non booting configuration unless
"nolapic noapic" was used.

I also disabled the local APIC parsing in this case, although
that's only cosmetic (suppresses a few printks)

This hopefully makes nolapic work in all cases.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>