Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Change Set:

1. Extended the upper boundary restriction for the module parameter
   max_sgl_entries. Earlier, the max_sgl_entries was capped at the
   SCSI_MAX_SG_SEGMENTS kernel definition. With this change, the user
   would be able to set the max_sgl_entries to any value which is
   greater than SCSI_MAX_SG_SEGMENTS and less than the minimum of
   SCSI_MAX_SG_CHAIN_SEGMENTS & hardware limit (Calculated using
   IOCFacts's MaxChainDepth).

2. Added a print for the message log whenever the user sets the
   max_sgl_entries to a value greater than SCSI_MAX_SG_SEGMENTS to
   warn about the kernel definition overriding.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.

The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y

where a b c d are threshold flags 0 1 2 3

Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
   driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
   time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
   firmware, then print the sensor number, the maximum threshold number it
   has exceed and the current temperature of this sensor.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The "issue_reset" can be used uninitialized.  It should be set to false
at the start.

Also I cleaned up the types a little by using bool.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.

When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.

The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.

But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.

So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.

When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.

Change set in v1:

1. Declared the _base_get_ioc_facts() functions at the beginning of the mpt3sas_base.c file
instead of moving all these functions before mpt3sas_base_map_resources() function
        a. _base_wait_for_doorbell_int()
        b. _base_wait_for_doorbell_ack()
        c. _base_wait_for_doorbell_not_used()
        d. _base_handshake_req_reply_wait()
        e. _base_get_ioc_facts()

2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.

3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
        a. _base_release_memory_pools()
        b. _base_allocate_memory_pools()
        c. _base_send_ioc_init()
        d. _base_make_ioc_operational()
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Added following branding Strings for Intel custom HBAs support.

Driver String:                                  Vendor ID       Device ID       SubSystemVendor ID      SubSystemDevice ID
Intel(R) Integrated RAID Module RMS3JC080       0x1000          0x0097          0x8086                  0x3521
Intel(R) RAID Controller RS3GC008               0x1000          0x0097          0x8086                  0x3522
Intel(R) RAID Controller RS3FC044               0x1000          0x0097          0x8086                  0x3523
Intel(R) RAID Controller RS3UC080               0x1000          0x0097          0x8086                  0x3524
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Copyright in driver sources is updated for year the 2014.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In _scsih_probe, delay the call to scsi_add_host until the host has been
fully set up.

Otherwise, the default .can_queue value of 1 causes scsi-mq to set the block
layer request queue size to its minimum size, resulting in awful performance.

In _scsih_probe error handling, call mpt3sas_base_detach rather than
scsi_remove_host to properly clean up in reverse order.

In _scsih_remove, call scsi_remove_host earlier to clean up in reverse order.
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNagalakshmi Nandigama <Nagalakshmi.Nandigama@avagotech.com>
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

On systems with a non power-of-two CPU count the existing MSI-X grouping
code failed to distribute interrupts correctly. Rework the code to
handle arbitrary processor counts.

Also remove the hardcoded upper limit on the number of processors so we
can boot on large systems.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NSreekanth Reddy <Sreekanth.reddy@avagotech.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Race conditions are theoretically possible between the MPT PCI device
removal and the generic PCI bus rescan and device removal that can be
triggered via sysfs.

To avoid those race conditions make the MPT PCI code use
pci_stop_and_remove_bus_device_locked().
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Added a driver module parameter max_msix_vectors. Using this module parameter
the maximum number of MSI-X vectors could be set.

The number of MSI-X vectors used would be the minimum of MSI-X vectors
supported by the HBA, the number of CPU cores and the value set to
max_msix_vectors module parameter.

The default value of this module parameter is set to 8. The default value of
this parameter is set to 8 inorder to reduce the amount of memory required for
Reply Descriptor Post queue.  This is because with the higher MSI-X vectors,
some times kernel is not able to allocate the requested amount of memory and
crash is observed. To overcome this problem, the default value is set to 8.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If mpt3sas_base_map_resources takes an early error path then its
counterpart, mpt3sas_base_free_resources needs to be careful about
cleaning up:

  1 - _base_mask_interrupts and _base_make_ioc_ready require memory
      mapped I/O registers, make sure that this is true.

  2 - _base_free_irq iterates over the adapter's reply_queue_list, so
      move this list head initialization out of _base_enable_msix to
      _scsih_probe so this will always be safe.

  3 - check that the controller PCI device and its BARs have been
      enabled before disabling them.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Hardware timing requirements is updated in order to comply with firmware
requirement.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The Copyright String in all mpt3sas files are changed to 2012-2013.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The variable 'chain_flags' and 'phy_number' are initialized but never used
otherwise, So remove those unused variables.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

linux/version.h is not necessary as detected by checkversion.pl script.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: N"Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

These driver files are initially, substantially similar to mpt2sas but,
because mpt2sas is going into maintenance mode and mp3sas will become heavily
developed, we elected to keep the code bases separate.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Reviewed-by: NNagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.

[jejb: fix whitespace problems]
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Updating the customer branding string for "SSD 910 Series" controller
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The Copyright String in all the drivers sources were changed to 2012
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value

If the specified max_queue_depth setting is less than the
expected number of internal commands, then driver will calculate
the queue depth size to a negitive number. This negitive number
is actually a very large number because variable is unsigned
16bit integer. So, the driver will ask for a very large amount of
memory for message frames and resulting into oops as memory
allocation routines will not able to handle such a large request.

So, in order to limit this kind of oops, The driver need to set
the max_queue_depth to a scsi mid layer's can_queue value. Then
the overall message frames required for IO is minimum of either
(max_queue_depth plus internal commands) or the IOC global
credits.
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id().
This is because smp_processor_id() is not called in preempt safe condition.

To fix this issue, use raw_smp_processor_id instead of smp_processor_id.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The ioc->pfacts member in the IOC structure is getting set to zero
following a call to _base_get_ioc_facts due to the memset in that routine.
So if the ioc->pfacts was read after a host reset, there would be a NULL
pointer dereference. The routine _base_get_ioc_facts is called from context
of host reset.  The problem in _base_get_ioc_facts  is the size of
Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60,
so there is a four byte overflow resulting from the memset.

Also, there is memset in _base_get_port_facts using the incorrect structure,
it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix several endian issues found by runing sparse.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Modified the source code as per the findings reported by the source
code analysis tool. Source code for the following functionalities
has been touched. None of the driver functionalities has changed.

- SMP Passthrough IOCTL
- Debug messages for MPT Replies (i.e. bit 9 of Logging Level)
- Task Management using sysfs
- Device removal, i.e. when a target device (including any PD within a volume)
  is removed, and Volume Deletion.
- Trace Buffer
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Improvement were made to better protect the sas_device, raid_device, and expander_device lists

There were possible race conditions surrounding reading an object
from the link list while from another context in the driver was
removing it. The nature of this enhancement is to rearrange locking
so the link lists are better protected.

Change set:
(1) numerous routines were rearranged so spin locks are held through
the entire time a link list object is being read from or written to.
(2) added new routines for object deletion from link list.  Thus ensuring
lock was held during the deletion of the link list object, then and memory
for object freed outside the lock. The memory was freed outside the lock
so driver had access to device object info which was required for
notifying the scsi mid layer that a device was getting deleted.
(3) added the ioc->blocking_handles parameter.  This is a bitmask used
to identify which devices need blocking when there is device loss.  This was
introduced so that lock can be held for the entire time traversing the link
list objects, and the bitmask was set to indicate which device handles need
blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed,
with the respective device handle the scsi mid layer is called for moving
devices into blocking state.
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

commit 44c10138 (PCI: Change all
drivers to use pci_device->revision) converted all drivers to use
pci_dev->revision.  Convert these three drivers which got missed.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fix ensures that the IOP_LOGINFO_CODE_TASK_TERMINATED
messages do not clutter the sas_log_info messages.

Bugzilla 42142 - mpt2sas: Number specified in wrong base
https://bugzilla.kernel.org/show_bug.cgi?id=42142Signed-off-by: NSathisha Nanjappa <sathisha.nanjappa@hp.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The old pci_remove_bus_device actually did stop and remove.

Make the name reflect that to reduce confusion.

This patch is done by sed scripts and changes back some incorrect
__pci_remove_bus_device changes.
Suggested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The __get_free_pages can fail, so the return value should be checked.
Spotted thanks to Stanislaw.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.

The patch fixes the issue by jumping afer mutex_unlock() call.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Removed redundant calling of _scsih_probe_devices() from _scsih_probe as
it is getting called from _scsih_scan_finished.

Also moved the function scsi_scan_host(shost) to get called after the
volumes on warp drive are reported to the OS. Otherwise by the time
the (ioc->hide_drives) flags is set, the volumes on warp drive
are reported to the OS already.

Also modified the initialization of reply queues only in case of driver load
time in the function _base_make_ioc_operational().
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 921cd802 ("[SCSI] mpt2sas: New feature - Fast Load
Support") moved handling of the diag_buffer_enable module parameter
from mpt2sas_base.c to mpt2sas_scsih.c, but it left an old copy of the
parameter in mpt2sas_base.c.  Remove the unused stub.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When computing reply_queue_count (the number of MSI-X vectors to use),
the driver does

	ioc->reply_queue_count = min_t(u8, ioc->cpu_count,
	    ioc->msix_vector_count);

However, on a big machine, ioc->cpu_count could be outside the range
that fits in a u8; eg a system with 256 CPUs will end up
reply_queue_count set to 0.

Fix this by calculating the minimum as ints and then letting the
assignment to reply_queue_count handle integer demotion.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 911ae943 ("[SCSI] mpt2sas: Added NUNA IO support in driver
which uses multi-reply queue support of the HBA") added new
allocations to the beginning of mpt2sas_base_attach(), which means
directly returning an error on failure of mpt2sas_base_map_resources()
will leak those allocations.

Fix this by doing "goto out_free_resources" in this place too, as the
rest of the function does.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Acked-by: N"Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The amount of memory required for tracking chain buffers is rather
large, and when the host credit count is big, memory allocation
failure occurs inside __get_free_pages.

The fix is to limit the number of chains to 100,000.  In addition,
the number of host credits is limited to 30,000 IOs. However this
limitation can be overridden this using the command line option
max_queue_depth.  The algorithm for calculating the
reply_post_queue_depth is changed so that it is equal to
(reply_free_queue_depth + 16), previously it was (reply_free_queue_depth * 2).
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Rearrange the the code so that the completion queues are initialized prior to sending the request to controller firmware
Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NNagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>