Previously mce_panic used a simple heuristic to avoid printing
old so far unreported machine check events on a mce panic. This worked
by comparing the TSC value at the start of the machine check handler
with the event time stamp and only printing newer ones.

This has a couple of issues, in particular on systems where the TSC
is not fully synchronized between CPUs it could lose events or print
old ones.

It is also problematic with full system synchronization as it is
added by the next patch.

Remove the TSC heuristic and instead replace it with a simple heuristic
to print corrected errors first and after that uncorrected errors
and finally the worst machine check as determined by the machine
check handler.

This simplifies the code because there is no need to pass the
original TSC value around.

Contains fixes from Ying Huang

[ Impact: bug fix, cleanup ]
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Ying Huang <ying.huang@intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Normally the machine check handler ignores corrected errors and leaves
them to machine_check_poll(). But when panicing mcp won't run, so
log all errors.

Note: this can still miss some cases until the "early no way out"
patch later is applied too.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Experience has shown that struct mce which is used to pass an machine
check to the user space daemon currently a few limitations.  Also some
data which is useful to print at panic level is also missing.

This patch addresses most of them. The same information is also
printed out together with mce panic.

struct mce can be painlessly extended in a compatible way, the mcelog
user space code just ignores additional fields with a warning.

- It doesn't provide a wall time timestamp. There have been a few
  complaints about that. Fix that by adding a 64bit time_t

- It doesn't provide the exact CPU identification. This makes
  it awkward for mcelog to decode the event correctly, especially
  when there are variations in the supported MCE codes on different
  CPU models or when mcelog is running on a different host after a panic.
  Previously the administrator had to specify the correct CPU
  when mcelog ran on a different host, but with the more variation
  in machine checks now it's better to auto detect that.
  It's also useful for more detailed analysis of CPU events.
  Pass CPUID 1.EAX and the cpu vendor (as encoded in processor.h) instead.

- Socket ID and initial APIC ID are useful to report because they
  allow to identify the failing CPU in some (not all) cases.
  This is also especially useful for the panic situation.
  This addresses one of the complaints from Thomas Gleixner earlier.

- The MCG capabilities MSR needs to be reported for some advanced
  error processing in mcelog
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

The old struct mce had a limitation to 256 CPUs. But x86 Linux supports
more than that now with x2apic. Add a new field extcpu to report the
extended number.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

This makes it easier for tools who want to extract the mcelog out of
crash images or memory dumps to adapt to changing struct mce size.
The length field replaces padding, so it's fully compatible.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Keep a count of the machine check polls (or CMCI events) in
/proc/interrupts.

Andi needs this for debugging, but it's also useful in general
to see what's going in by the kernel.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Useful for debugging, but it's also good general policy
to have a counter for all special interrupts there. This makes it easier
to diagnose where a CPU is spending its time.

[ Impact: feature, debugging tool ]
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Merge reason: arch/x86/kernel/irqinit_{32,64}.c unified in irq/numa
and modified in x86/mce3; this merge resolves the conflict.

Conflicts:
	arch/x86/kernel/irqinit.c
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Merge reason: irq/numa didnt build because this commit:

  2759c328: x86: don't call read_apic_id if !cpu_has_apic

Had a dependency on x86/cpufeature changes. Pull in that
(small) branch to fix the dependency.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Conflicts:
	arch/mips/sibyte/bcm1480/irq.c
	arch/mips/sibyte/sb1250/irq.c

Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Update documentation on fan_max
  hwmon: (lm78) Add missing __devexit_p()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix section attribute warnings.
  sparc64: Fix SET_PERSONALITY to not clip bits outside of PER_MASK.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  3c509: Add missing EISA IDs
  MAINTAINERS: take maintainership of the cpmac Ethernet driver
  net/firmare: Ignore .cis files
  ath1e: add new device id for asus hardware
  mlx4_en: Fix a kernel panic when waking tx queue
  rtl8187: add USB ID for Linksys WUSB54GC-EU v2 USB wifi dongle
  at76c50x-usb: avoid mutex deadlock in at76_dwork_hw_scan
  mac8390: fix build with NET_POLL_CONTROLLER
  cxgb3: link fault fixes
  cxgb3: fix dma mapping regression
  netfilter: nfnetlink_log: fix wrong skbuff size	calculation
  netfilter: xt_hashlimit does a wrong SEQ_SKIP
  bfin_mac: fix build error due to net_device_ops convert
  atlx: move modinfo data from atlx.h to atl1.c
  gianfar: fix babbling rx error event bug
  cls_cgroup: read classid atomically in classifier
  netfilter: nf_ct_dccp: add missing DCCP protocol changes in event cache
  netfilter: nf_ct_tcp: fix accepting invalid RST segments

* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6:
  headers_check fix: linux/net_dropmon.h
  headers_check fix: linux/auto_fs.h

Add fan_max description.

Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: NChristian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Several EISA device IDs for 3c509 family network cards are missing from 
the driver, making the cards unusable in their EISA mode.  Here's a fix to 
add them based on the EISA configuration files distributed by 3Com and our 
eisa.ids database.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds me as the maintainer of the CPMAC (AR7)
Ethernet driver.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix the following 'make headers_check' warnings:

  usr/include/linux/net_dropmon.h:7: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

fix the following 'make headers_check' warnings:

  usr/include/linux/auto_fs.h:17: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide_pci_generic: add quirk for Netcell ATA RAID

We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.

This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:

	commit 942dcd85
	("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")

and

	commit 4b58f17d
	("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: N"Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix bh leak in nilfs_cpfile_delete_checkpoints function

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI, i915: build fix (v2)
  acpi-cpufreq: fix printk typo and indentation
  ACPI processor: remove spurious newline from warning message
  drm/i915: acpi/video.c fix section mismatch warning
  ACPI: video: DMI workaround broken Acer 5315 BIOS enabling display brightness
  ACPI: video: DMI workaround broken eMachines E510 BIOS enabling display brightness
  ACPI: sanity check _PSS frequency to prevent cpufreq crash
  i7300_idle: allow testing on i5000-series hardware w/o re-compile
  PCI/ACPI: fix wrong ref count handling in acpi_pci_bind()
  cpuidle: fix AMD C1E suspend hang
  cpuidle: makes AMD C1E work in acpi_idle

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  fsldma: Fix compile warnings
  fsldma: fix memory leak on error path in fsl_dma_prep_memcpy()
  fsldma: snooping is not enabled for last entry in descriptor chain
  fsldma: fix infinite loop on multi-descriptor DMA chain completion
  fsldma: fix "DMA halt timeout!" errors
  fsldma: fix check on potential fdev->chan[] overflow
  fsldma: update mailling list address in MAINTAINERS

The nilfs_cpfile_delete_checkpoints() wrongly skips brelse() for the
header block of checkpoint file in case of errors.  This fixes the
leak bug.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>

Signed-off-by: NMatt Kraai <kraai@ftbfs.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gary Lin reports that a new device id needs to be added to the atl1e in
order to get some new Asus hardware to work properly.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branches 'bugzilla-13121+', 'bugzilla-13233', 'redhat-bugzilla-500311', 'pci-bind-oops', 'misc-2.6.30' and 'i7300_idle' into release

drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'

v2: move under DRM_I915 from DRM_I915_KMS
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Commit 4973b22a ("ACPI processor: reset the throttling state once it's
invalid") introduced a new warning which prints a spurious newline.

The ACPI_WARNING macro that is used already takes care of adding a
newline, after adding ACPI_CA_VERSION to the message. Remove the newline
to avoid the message getting split into two lines.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NLen Brown <len.brown@intel.com>

Currently acpi_video_exit() is exported as well as using __exit which causes:

  WARNING: drivers/acpi/video.o(__ksymtab+0x0): Section mismatch in reference from the variable __ksymtab_acpi_video_exit to the function .exit.text:acpi_video_exit()
  The symbol acpi_video_exit is exported and annotated __exit
  Fix this by removing the __exit annotation of acpi_video_exit or drop the export.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=13121Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=13376Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

When BIOS SETUP is changed to disable EIST, some BIOS
hand the OS an un-initialized _PSS:

        Name (_PSS, Package (0x06)
        {
            Package (0x06)
            {
                0x80000000,	// frequency [MHz]
                0x80000000,	// power [mW]
                0x80000000,	// latency [us]
                0x80000000,	// BM latency [us]
                0x80000000,	// control
                0x80000000	// status
            },
	    ...

These are outrageous values for frequency,
power and latency, raising the question where to draw
the line between legal and illegal.  We tend to survive
garbage in the power and latency fields, but we can BUG_ON
when garbage is in the frequency field.

Cpufreq multiplies the frequency by 1000 and stores it in a u32 KHz.
So disregard a _PSS with a frequency so large
that it can't be represented by cpufreq.

https://bugzilla.redhat.com/show_bug.cgi?id=500311Signed-off-by: NLen Brown <len.brown@intel.com>

CSUM copy to/from user assembler was missing allocatable and
executable attributes for .fixup
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] update mach-types
  [ARM] Add cmpxchg support for ARMv6+ systems (v5)
  [ARM] barriers: improve xchg, bitops and atomic SMP barriers
  Gemini: Fix SRAM/ROM location after memory swap
  MAINTAINER: Add F: entries for Gemini and FA526
  [ARM] disable NX support for OABI-supporting kernels
  [ARM] add coherent DMA mask for mv643xx_eth
  [ARM] pxa/palm: fix PalmLD/T5/TX AC97 MFP
  [ARM] pxa: add parameter to clksrc_read() for pxa168/910
  [ARM] pxa: fix the incorrectly defined drive strength macros for pxa{168,910}
  [ARM] Orion: Remove explicit name for platform device resources
  [ARM] Kirkwood: Correct MPP for SATA activity/presence LEDs of QNAP TS-119/TS-219.
  [ARM] pxa/ezx: fix pin configuration for low power mode
  [ARM] pxa/spitz: provide spitz_ohci_exit() that unregisters USB_HOST GPIO
  [ARM] pxa: enable GPIO receivers after configuring pins
  [ARM] pxa: allow gpio_reset drive high during normal work
  [ARM] pxa: save/restore PGSR on suspend/resume.