D4 has 1024, not 512, pressure levels.
Reported-by: NDavid Foley <favux.is@gmail.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The Wacom DTU-2231 tablet has two interfaces on its default configuration
and both have HID class, leading to the creation of two input devices
instead of one. Only the first one is used, so filter out the second.
Signed-off-by: NAristeu Rozanski <aris@redhat.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

So don't set ABS_RX/ABS_RY for them.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Touch resolution is reported to the userland by retrieving the value
from the HID descriptor. But pen resolution is not since it can not
be retrieved. The current Wacom X driver has a resolution table.
To centralize the source of these values, the resolution entries are
added in the wacom_features struct for x and y coordinates respectively.
The values are then reported to the userland.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There are two types of 1FGT devices supported in wacom_wac.c.
Changing them to follow the existing touchscreen format, i.e.,
only report BTN_TOUCH as a valid tool type.

Touch data will be ignored if pen is in proximity. This requires
a touch up event sent if touch was down when pen comes in. The
touch up event should be sent before any pen events are emitted.
Otherwise, two pointers would race for the cursor.

However, we can not send a touch up inside wacom_tpc_pen since
pen and touch are on different logical port. That is why we
have to check if touch is up before sending pen events.
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

So it would be easier for patch reviewers to follow the data path.
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

2FGT Tablet PC touch events were processed in _TAP_ format. Remove
them so we can change to _MT_ format.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

If we fail to retrieve HID descriptor we need to free allocated URB so
jump to proper label to do that.
Signed-off-by: NAlexander Strakh <strakh@ispras.ru>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Also remove fake ABS_RX/ABS_RY "axes" that were used to report physical
dimensions now that we have better way.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Reported-by: NDavid Foley <favux.is@gmail.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NAjay Ramaswamy <ajay@ramaswamy.net>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The drivers using the type B protocol all report tracking information
the same way. The contact id is semantically equivalent to
ABS_MT_SLOT, and the handling of ABS_MT_TRACKING_ID only complicates
the driver. The situation can be improved upon by providing a common
pointer emulation code, thereby removing the need for the tracking id
in the driver.  This patch moves all tracking event handling over to
the input core, simplifying both the existing drivers and the ones
currently in preparation.
Acked-by: NPing Cheng <pingc@wacom.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

The MT slots devices all follow the same initialization pattern
of creating slots and hinting about buffer size. Let drivers call
an initialization function instead, and make sure it can be called
repeatedly without side effects.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

In preparation for common code to handle a larger set of MT slots
devices, move the slots handling over to a separate file.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

Add the features struct and device table entry to enable yet another
version of Wacom Bamboo Pen (CTL460, Product ID 0xD4).
Signed-off-by: NKevin Granade <kevin.granade@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Adds new Bamboo Pen & Touch model - Bamboo P & T Special Edition
Medium (CTH661/L; Product ID = 0xdb).
Tested-by: NTobias Verbeke <tobias.verbeke@gmail.com>
Signed-off-by: NDavid Foley <favux.is@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add two new Bamboo Pen & Touch models:

Bamboo Comic Medium			(CTH661/S1; Product ID = 0xd8)
Bamboo P & T Special Edition Small	(CTH461/L;  Product ID = 0xdA)
Tested-by: NIRIE Shinsuke <irieshinsuke@yahoo.co.jp>
Tested-by: NAndrea Cadeddu <mrernia@gmail.com>
Signed-off-by: NDavid Foley <favux.is@gmail.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Sysfs attributes affecting device behavior should not be, by default,
world-writeable. If distributions want to allow console users access
these attributes they need to employ udev and friends to adjust
permissions as needed.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add a missing usb_free_urb() in usb_acecad_probe() error path.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Cintiq, being a display tablet, doesn't have mouse and associated BTN_s.
Make sure we do not specify them when registering Cintiq's input device
so that userland can retrieve the exact tool set the device supports.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We need to always call usb_autopm_put_interface() in wacom_open(),
not only when initialization fails, otherwise the device will be
marked as PM-busy and will never be put in suspended state.

Based on patch by Oliver Neukum.
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Currently the pressure range in Cintiq 21UX2 is limited to half of the
supported. This patch fixes the problem.
Signed-off-by: NAristeu Rozanski <aris@redhat.com>
Acked-by: NPing Cheng <pingc@wacom.com>
CC: stable@kernel.org
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

When runtime PM is enabled by default for input devices, X hangs in
wacom open:
[<ffffffff814a00ea>] mutex_lock+0x1a/0x40
[<ffffffffa02bc94b>] wacom_resume+0x3b/0x90 [wacom]
[<ffffffff81327a32>] usb_resume_interface+0xd2/0x190
[<ffffffff81327b5d>] usb_resume_both+0x6d/0x110
[<ffffffff81327c24>] usb_runtime_resume+0x24/0x40
[<ffffffff8130a2cf>] __pm_runtime_resume+0x26f/0x450
[<ffffffff8130a23a>] __pm_runtime_resume+0x1da/0x450
[<ffffffff8130a53a>] pm_runtime_resume+0x2a/0x50
[<ffffffff81328176>] usb_autopm_get_interface+0x26/0x60
[<ffffffffa02bc626>] wacom_open+0x36/0x90 [wacom]

wacom_open() takes wacom->lock and calls usb_autopm_get_interface(),
which in turn calls wacom_resume() which tries to acquire the lock
again.

The fix is to call usb_autopm_get_interface() first, before we take
the lock.

Since we do not do usb_autopm_put_interface() until wacom_close()
is called runtime PM is effectively disabled for the driver, however
changing it now would risk regressions so the complete fix will
have to wait till the next merge window.
Reported-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This adds support for hanwang Art Master HD 5012 electromagnetic tablet.
Signed-off-by: NXing Wei <weixing@hanwang.com.cn>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add necessary events so that Hanwang Art Master III tablet can be handled
by the stock xf86-input-wacom driver.
Signed-off-by: NXing Wei <weixing@hanwang.com.cn>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This adds support for Pen on Bamboo Pen and Bamboo Pen&Touch devices.
Touchpad is handled by previous Bamboo Touch logic.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This is in preparation of pen support in same irq handler.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Bamboo P&T need to use second form of usb_set_report() to
ask to report tablet data.

With previous addition of Bamboo Touch, BTN_TOOL_TRIPLETAP is now used
for both TABLETPC2FG and BAMBOO_PT types.  So reduced check to
match type=TABLETPC2FG.

This change shows redundant check for !TABLETPC2FG in else statement.
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The Bamboo Touch reports a sub-screen resolution of 480x320.  The
signal-to-noise ratio is only about 100, so filtering is needed in
order to reduce the jitter to a usable level. However, the low
resolution leads to round-off errors in the EWMA filter, resulting in
extremely jerky pointer motion. This patch explicitly sets a higher
resolution for those devices, and tells this to the completion handler
via a low-resolution quirk.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add support for the Bamboo Touch trackpad, and make it work with
both the Synaptics X Driver and the Multitouch X Driver. The device
uses MT slots internally, so the choice of protocol is a given.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Collect device-specific code into a single function, and use quirks to
flag specific behavior instead.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The Bamboo devices have multiple interfaces which need to be setup
separately. Use the HID parsing mechanism to achieve that.
Signed-off-by: NPing Cheng <pinglinux@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The signal-to-noise ratio varies between devices, but currently all
devices are treated the same way. Add fuzz parameters to the feature
struct, allowing for tailored treatment of devices.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add support for Art Master III tablet of BeiJing HanwangTechnology Co, Ltd.
Signed-off-by: NXing Wei <weixing@hanwang.com.cn>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This fixes a regression introduced in
3b57ca0f.

The data[6] byte contains either 1 or -1 depending on the whether the
mouse wheel on older wacom tablets is moved down (1) or up (-1).  The
patch introduced in the above commit changed the cast from (signed char)
to (signed).  When cast as a signed integer and negated, the value of -1
(stored in the byte as 0xff) became -255 rather than 1.  This patch
reverts the cast to a (signed char) and also removes an unnecessary
(signed) cast, as all the values operated on are bitmasked.
Signed-off-by: NMike Auty <ikelos@gentoo.org>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Cc; stable@kernel.org
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Change all call sites in drivers/input to not access the ABS axis
information directly anymore. Make them use the access helpers instead.

Also use input_set_abs_params() when possible.
Did some code refactoring as I was on it.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>