This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):

WARNING: CPU: 3 PID: 117 at kernel/softirq.c:150 __local_bh_enable_ip+0xaa/0x110()
Call Trace:
 [<ffffffff814f71eb>] dump_stack+0x4f/0x7b
 [<ffffffff8105e56a>] warn_slowpath_common+0x8a/0xc0
 [<ffffffff8105e65a>] warn_slowpath_null+0x1a/0x20
 [<ffffffff81062b2a>] __local_bh_enable_ip+0xaa/0x110
 [<ffffffff814ff229>] _raw_spin_unlock_bh+0x39/0x40
 [<ffffffffa03a7f94>] fc_seq_set_resp+0xe4/0x100 [libfc]
 [<ffffffffa02e604a>] ft_free_cmd+0x4a/0x90 [tcm_fc]
 [<ffffffffa02e6972>] ft_release_cmd+0x12/0x20 [tcm_fc]
 [<ffffffffa042bd66>] target_release_cmd_kref+0x56/0x90 [target_core_mod]
 [<ffffffffa042caf0>] target_put_sess_cmd+0xc0/0x110 [target_core_mod]
 [<ffffffffa042cb81>] transport_release_cmd+0x41/0x70 [target_core_mod]
 [<ffffffffa042d975>] transport_generic_free_cmd+0x35/0x420 [target_core_mod]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: NJoern Engel <joern@logfs.org>
Reviewed-by: NAndy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.

Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.

To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This does nothing, and there are many other places where
transport_cmd_check_stop_to_fabric()'s retval is not checked>, If we
wanted to check it here, we should probably do it those other places too.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds an optional fabric driver provided SGL limit
that target-core will honor as it's own internal I/O maximum
transfer length limit, as exposed by EVPD=0xb0 block limits
parameters.

This is required for handling cases when host I/O transfer
length exceeds the requested EVPD block limits maximum
transfer length. The initial user of this logic is qla2xxx,
so that we can avoid having to reject I/Os from some legacy
FC hosts where EVPD=0xb0 parameters are not honored.

When se_cmd payload length exceeds the provided limit in
target_check_max_data_sg_nents() code, se_cmd->data_length +
se_cmd->prot_length are reset with se_cmd->residual_count
plus underflow bit for outgoing TFO response callbacks.
It also checks for existing CDB level underflow + overflow
and recalculates final residual_count as necessary.

Note this patch currently assumes 1:1 mapping of PAGE_SIZE
per struct scatterlist entry.
Reported-by: NCraig Watson <craig.watson@vanguard-rugged.com>
Cc: Craig Watson <craig.watson@vanguard-rugged.com>
Tested-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

For every command, we set se_ordered_id by doing atomic_inc_return on
dev->dev_ordered_id for the corresponding device.  However, the only
places this value gets used are in pr_debug() calls, which doesn't
seem worth an extra atomic op per IO.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Make the warning about unsupported SCSI opcode more useful:

 - Add in the initiator name so we know who's sending it.
 - Print the warning even for opcodes that spc_parse_cdb() knows about
   but that we don't handle.
Signed-off-by: NJoern Engel <joern@purestorage.com>
Signed-off-by: NSpencer Baugh <sbaugh@catern.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

It's not necessarily a fatal error if a command with a data-out phase
has a data length that differs from the transport data length (e.g.
PERSISTENT RESERVE OUT might have a parameter list length in the CDB
that's smaller than the FC_DL field), so allow these commands.  The
Windows compliance test sends them.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NSpencer Baugh <sbaugh@catern.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In case a LU spans 64bit sectors, fixed size sense data information
field is only 32 bits which means the sector information will be truncated.

Thus, if the LU spans 64bit sectors, use descriptor format sense data to
correctly report sector information.
Reported-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Make sure that the input sense buffer has sufficient length
to fit the information descriptor (12 additional bytes).
Modify scsi_set_sense_information to receive the sense buffer
length and adjust its callers scsi target and libata.

(Fix patch fuzz in scsi_set_sense_information - nab)
Reported-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

PI errors were reported with ILLEGAL_REQUEST sense key but
there was actually no problem with the request. Target
detected PI errors should be reported with aborted command
sense key.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Instead of open coding the sense buffer construction, use
scsi scsi_build_sense_buffer() and scsi_set_sense_information()
helpers which moved to scsi_common.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Move the code for translating a sense_reason_t code into a SCSI status
ASC and ASCQ codes from transport_send_check_condition_and_sense() into
the new function translate_sense_reason(). Convert the switch statement
that performs the translation into table-driven code.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Inline this function in its call site since it performs a trivial
task and since it is only called once.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Use kvfree() instead of open-coding it.
Signed-off-by: NPekka Enberg <penberg@kernel.org>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SAM mandates that an BUS DEVICE RESET FUNCTION OCCURRED
UA needs to be send after a LUN RESET tmr has completed.

(Update to use target_ua_allocate_lun - hch)
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We need to use 'se_dev_entry' as argument when allocating
UAs, otherwise we'll never see any UAs for an implicit
ALUA state transition triggered from userspace.

(Add target_ua_allocate_lun() common caller - nab)
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

As we're now using a list to hold the LUNs the target core
can now converted to use 64-bit LUNs internally.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:

$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

With se_port and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra lock to protect se_lun->lun_se_dev
assignment.

This patch also converts backend drivers to use call_rcu() release
to allow any se_device readers to complete.  The call_rcu() instead
of kfree_rcu() is required here because se_device is embedded into
the backend driver specific structure.

Also, convert se_lun->lun_stats to use atomic_long_t within the
target_complete_ok_work() completion callback, and add FIXME for
transport_lookup_tmr_lun() with se_lun->lun_ref.

Finally, update sbp_update_unit_directory() special case usage with
proper rcu_dereference_raw() and configfs symlink comment.
Reported-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch eliminates all se_port + t10_alua_tg_pt_gp_member usage,
and converts current users to direct se_lun pointer dereference.

This includes the removal of core_export_port(), core_release_port()
core_dev_export() and core_dev_unexport().  Along with conversion
of special case se_lun pointer dereference within PR ALL_TG_PT=1
and ALUA access state transition UNIT_ATTENTION handling.

Also, update core_enable_device_list_for_node() to reference the
new per se_lun->lun_deve_list when creating a new entry, or
replacing an existing one via RCU.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Instead of starting a thread from transport_clear_lun_ref() that
waits for LUN shutdown, wait in that function for LUN shutdown
to finish. Additionally, change the return type of
transport_clear_lun_ref() from int to void.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch converts se_tpg->acl_node_lock to struct mutex, so that
->acl_node_acl walkers in core_clear_lun_from_tpg() can block when
calling core_disable_device_list_for_node().

It also updates core_dev_add_lun() to hold ->acl_node_mutex when
calling core_tpg_add_node_to_devs() to build ->lun_entry_hlist
for dynamically generated se_node_acl.
Reviewed-by: NHannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The only instance of ->put_session is in qla2xxx, and was added by commit
aaf68b ("tcm_qla2xxx: Convert to TFO->put_session() usage") with the following
description:

    This patch converts tcm_qla2xxx code to use an internal kref_put() for
    se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
    can be held while calling qlt_unreg_sess() for the final put.

But these day we're already holding the hardware lock over qlt_unreg_sess in
the ->close_session callback, so we're fine without this method.

(Re-add missing tcm_qla2xxx_release_session + drop put_session usage - nab)
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.

For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.

(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Even if the device backend is initialized with protection info is
enabled, some requests don't have the protection info attached for
WRITE SAME command issued by block device helpers, WRITE command with
WRPROTECT=0 by SG_IO ioctl, etc.

So when TCM loopback fabric module is used, se_cmd->t_prot_sg is NULL
for these requests and performing WRITE_INSERT of PI using software
emulation by sbc_dif_generate() causes kernel crash.

To fix this, introduce SCF_PASSTHROUGH_PROT_SG_TO_MEM_NOALLOC for
se_cmd_flags, which is used to determine that se_cmd->t_prot_sg needs
to be allocated or use pre-allocated protection information by scsi
mid-layer.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The first argument of these two functions is always identical
to se_cmd->se_sess. Hence remove the first argument.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Fields t_bidi_data_sg and t_bidi_data_nents are set only in the presence
of BIDI commands. This means that the underlying code (for example TCMU)
cannot inspect them when the SCSI command is not a BIDI one.

Ensure the code always initializes these fields with the given values,
even when the SCSI command is not a BIDI one. Set t_bidi_data_sg to
sgl_bidi (which should be NULL for non-BIDI commands) and
t_bidi_data_nents to sgl_bidi_count (which should be 0 for non-BIDI
commands). This allows the underlying code to use these fields
unconditionally.
Signed-off-by: NIlias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: NVangelis Koukis <vkoukis@arrikto.com>
Reviewed-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Drivers may override the WCE flag, in which case the DPOFUA flag in
MODE SENSE might differ from the check used to reject invalid FUA
bits in sbc_check_dpofua.  Also now that we reject invalid FUA
bits early there is no need to duplicate the same buggy check
down in the fileio code.

As the DPOFUA flag controls th support for FUA bits on read and
write commands as well as DPO key off all the checks off a single
helper, and deprecate the emulate_dpo and emulate_fua_read attributs.

This fixes various failures in the libiscsi testsuite.

Personally I'd prefer to also remove the emulate_fua_write attribute
as there is no good reason to disable it, but I'll leave that for
a separate discussion.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Instead of providing DIF verify routines for read/write
that are almost identical and conditionally copy protection
information, just let the caller do the right thing.

Have a single sbc_dif_verify that handles an sgl (that
does NOT copy any data) and a protection information copy
routine used by rd_mcp and fileio backend.

In the WRITE case, call sbc_dif_verify with cmd->t_prot_sg
and then do the copy from it to local sgl (assuming the verify
succeeded of course). In the READ case, call sbc_dif_verify
with the local sgl and if it succeeds, copy it to t_prot_sg (or
not if we are stripping it).

(Fix apply breakage from commit c8367778 - nab)
Tested-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

It seems like we only care if a transport is passthrough or not. Convert
transport_type to a flags field and replace TRANSPORT_PLUGIN_* with a
flag, TRANSPORT_FLAG_PASSTHROUGH.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Reviewed-by: NIlias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

All of these files were only building on non-x86 because of
the indirect of inclusion of vmalloc.h by, of all things,
"net/inet_hashtables.h"

None of this got caught during build testing, because on x86
there is an implicit vmalloc.h include via on of the arch asm/
headers.

This fixes all of these
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code like " &= ~CMD_T_BUSY | ..." only clears CMD_T_BUSY but not
the other flag. Modify these statements such that both flags are
cleared.

(Fix fuzz for target_write_prot_action code in mainline - nab)
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The function transport_complete_qf() must call either
queue_data_in() or queue_status() but not both.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists.  So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.

(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Avoid that sparse complains about context imbalances.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.

It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.

Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.

This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: NChristoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.

This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().

A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.

(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>