We'll be needing to the call the power seqeuencer functions while
already holding pps_mutex, so split the locking out to small wrapper
functions.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we read the current power seqeuncer delays from the registers
(as well as looking at the vbt and spec values) we may end up
corrupting delays we already initialized when we switch to another
pipe and the power seqeuncer there has different values currently
in the registers.

So make sure we only initialize the delays once even if
intel_dp_init_panel_power_sequencer() gets called multiple times.

There was some discussion in the review about when exactly we need to
unlock the pps. Quoting Bspec:

"If this bit is not a zero, it activates the register write protect
 and writes to those registers will be ignored unless the write
 protect key value is set in the panel sequencing control register."
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[danvet: Add Bspec quote per review discussion between Imre and
Ville.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The power seqeuncer delays are fixed for a given panel, so we can keep
them around once computed.

Not that on VLV/CHV we still re-compute them every time we initialize
the power seqeuncer registers, but that will change soon enough.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

want_panel_vdd is a bool so it can't cope with interleaving on/off calls
from multiple threads. If we want to make that possible we'd need to
convert want_panel_vdd into a proper ref count. But an easier fix is to
remove the high level vdd on/off calls from detect/hpd code paths and
just rely on the delayed vdd off to avoid needless vdd on<->off ping
pong.

After this change only the encoder enable/disable paths use the high
level functions, which is fine since both the on and off low level edp
vdd calls from intel_dp_aux_ch() happen without dropping pps_mutex in
between and so want_panel_vdd can't change in between.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only ports B and C have the power sequencer and backlight controls,
so complain if we ever try to register an eDP connector on some other
port.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everything else can be derived from that. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Clear the override bits to make sure the hardware manages
the TX FIFO reset master on its own.

v2: Squash with the earlier attempt at forcing the override bits
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The register can house two different swing marging/deemph settings at
once. However only one gets used based on some other bits. Make sure we
set those bits correctly to make the hardware use the settings we
provided.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Even though it's unliky, we should check each aux transaction not just
the first one. Also

commit ce31d9f4
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date:   Mon Sep 29 18:29:52 2014 -0400

    drm/i915: preserve other DP_TEST_SINK bits.

added a new aux transaction before the one which was checked. Fix
this.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by Ville constifying the send buffer for pach_aux.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Use pack_aux() to construct the PSR exit DPMS D0 AUX message,
and use the defines from dp_dp_helper.h to populate the message
contents.

v2: Use sizeof() for message size (Jani)
    Use a generic loop to write EDP_PSR_AUX_DATA registers

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- fini goes with init, so call it intel_power_domains_fini. While
  at it shovel some of the fini code that leaked out of it back in.

- give power_enabled functions the verb _is_ to make the meaning clearer.
  Also use a __ prefix instead of _unlocked to really discourage users.

- rename runtime_pm_init/fini to enable/disable since that's what they do.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Sink crc was implemented based on dp 1.1 spec that had all TEST_SINK bits
reserved reading all 0s. But when reviewing my latest changes on sink crc
Todd warned me that on new specs we have other valid bits on this reg that we
might want to preserve.

Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In some cases like when PSR just got enabled the panel need more vblank
times to calculate CRC. I figured that out with the new PSR test cases
facing some cases that I had a green screen but a blank CRC. Even with
2 vblank waits on kernel + 2 vblank waits on test case.

So let's give up to 6 vblank wait time. However we now check for
TEST_CRC_COUNT that shows when panel finished to calculate CRC and
has it ready.

v2: Jani pointed out attempts decrements was wrong and should never reach
the error condition. And Daniel pointed out that EIO is more appropriated than
EGAIN. Also I realized that I have to read test_crc_count after setting
test_sink

v3: Rebase and adding error message

Cc: Todd Previte <tprevite@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's make sure PSR is propperly disabled before to re-enabled it.

According to Spec, after disabled PSR CTL, the Idle state might occur
up to 24ms, that is one full frame time (1/refresh rate),
plus SRD exit training time (max of 6ms),
plus SRD aux channel handshake (max of 1.5ms).

So if something went wrong PSR will be disabled until next full
enable/disable setup.

v2: The 24ms above takes in account 16ms for refresh rate on 60Hz mode. However
on low frequency modes this can take longer. So let's use 50ms for safeness.

v3: Move wait out of psr.lock critical area.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The panel has to be reconfigured only when it really loose the power.
The traditional enable/disable sequence already take care of this so we can
minimize the time spend on every re-enable.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Skylake doesn't use the pre-charge field now, but, instead, we need to
specify the total number of SYNC pulses for the SYNC phase (pre-charge +
SYNC pattern pules). Let's use the default value (32) for that.

v3: increase DP AUX TX timeout as 400us is not to be used on SKL
    apparently (Jesse).
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to provide a vfunc that will make the code in intel_dp_aux_ch()
loop once to start the AUX transaction. The return value (clock divider)
is unused on SKL, so just return 1.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So we can apply the old aux_ctl = dp_ctl + 0x10 rule again.
Reviewed-by: NThomas Wood <thomas.wood@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They are similar to Haswell.

v2: Rebased on top of drm-intel-nightly
v3: Rebased on top of Sonika's DP train defines renaming
Reviewed-by: NThomas Wood <thomas.wood@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't need to setup everything else if it doesn't match all conditions.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

psr_enabled is already by itself a setup once so let's put the W/As there and
rename old setup once to setup_vsc.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If something while getting panel CRC this means that probably hw I/O error
so hw is busted and try again shouldn't help much.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

eDP panels are generally designed to support only a single clock and
lane configuration.

commit 56071a20
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Tue May 6 14:56:52 2014 +0300

    drm/i915: use lane count and link rate from VBT as minimums for eDP

should have started using the optimal link parameters for eDP
panels. Turns out a certain other OS uses DPCD instead of VBT, which
means trusting VBT on this may not be so reliable after all. Follow
suit.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81647Tested-by: NAdam Jirasek <libm3l@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79386Tested-by: NNarthana Epa <narthana.epa+freedesktop@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This goes back to

commit 06ea66b6
Author: Todd Previte <tprevite@gmail.com>
Date:   Mon Jan 20 10:19:39 2014 -0700

    drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable devices

Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Pimp commit message a bit.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Oops, apparently intel_hdmi/intel_dp is the encoder - an object with a
distinct lifetime to the connector, and so we cannot simply reuse the
common function to unset and free the edid.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The limited color range knob is in the port registers on
g4x and vlv/chv for HDMI, and on g4x for DP. Add the relevant code
to read out the hardware state into pipe config. On vlv/chv the
DP port limited color range knob is in PIPECONF for which we
already have readout code.

Cc: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NChris Clayton <chris2553@googlemail.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Jani wanted some comments to explain why we call certain vdd on/off
functions in certain places.

v2: Make the comments more thorough (Imre)
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to turn the DP port off after the pipe, otherwise the pipe won't
turn off properly on certain pch platforms at least (happens on my ILK for
example).  This also matches the BSpec modeset sequence better. We still
don't match the spec exactly though (eg. audio disable should happen
much earlier), but at last this eliminates the nasty
wait_for_pipe_off() timeouts.

We already did the port disable after the pipe for VLV/CHV and for CPU
eDP.

For g4x leave the port disable where it is since that matches the
modeset sequence in the documentation and I don't have a suitable
machine to test if the other order would work.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec says we should enable the DP port before enabling panel power,
and that the port must be enabled with training pattern 1. Do so.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On VLV/CHV the panel power sequencer may need to be "kicked" a bit to
lock onto the new port, and that needs to happen before any aux
transfers are attempted if we want the aux transfers to actaully
succeed. So turn on panel power (part of the "kick") before aux
transfers (DPMS_ON + link training).

This also matches the documented modeset sequence better for pch
platforms. The documentation doesn't explicitly state anything about the
DPMS or link training DPCD writes, but the panel power on step is
always listed before link training is mentioned.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=70117Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Try to make sure we find the power sequencer that the BIOS used
by first looking for one which has the panel power enabled, then
fall back to one with VDD force bit enabled, and finally look at
just the port select bits. This should make us pick the correct
power sequencer when the BIOS has already enabled the panel.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[danvet: Shorten the vlv_intial_pps_pipe to make lines fit into 80
chars.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The power sequencer loses its state when the disp2d power well is down.
Clear the dev_priv->pps_pipe tracking so that the power sequencer state
gets reinitialized the next time it's needed.

v2: Fix the pps_mutex vs. power_domain mutex deadlock by taking power
    domain reference first
v3: Rename from edp_pps_(un)lock() to just pps_(un)lock() for the future,
    update due to backlight code changes
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VLV/CHV have a per-pipe panel power sequencer which locks onto the
port once used. We need to keep track wich power sequencers are
locked to which ports.

v2: remove spurious whitespace change, rebase due to backlight changes (Imre)
Reviewed-by: NAntti Koskipaa <antti.koskipaa@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Break some really long lines to appease checkpatch a bit.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Introduce a new mutex (pps_mutex) to protect the power sequencer
state. For now this state includes want_panel_vdd as well as the
power sequencer registers.

We need a single mutex (as opposed to per port) because later on we
will need to deal with VLV/CHV which have multiple power sequencer
which can be reassigned to different ports.

v2: Add the locking to intel_dp_encoder_suspend too (Imre)
v3: Take care intel_edp_backlight_power() and
    _intel_edp_backlight_on/off(), deal with reboot notifier
    vlv_power_sequencer_pipe() call (Imre)
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we may query the edid multiple times following a detect, record the
EDID found during output discovery and reuse it. This is a separate
issue from caching the output EDID across detection cycles.

v2: Implement connector->force() callback so that edid is associated
with the connector for user overrides as well (Ville)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both gmch and pch detection routines used the exact same routine for
eDP, so de-duplicate.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: N: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.

Done using following cocci patch for each define:
@@
@@

 # define DP_TRAIN_VOLTAGE_SWING_400     (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0     (0 << 0)

...
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is no need to use hex_dump_to_buffer() since we have a kernel helper to
dump up to 64 bytes just via printk(). In our case the actual size is 15 bytes.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Add cast since %*ph expects and int for the size parameter.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>