All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.

Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.

As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the device id in the platform driver is hardcoded to an id
which is specific to AR9130/AR9132 SOCs as it supports only wmac (wireless mac)
of these SOCs. But this needs to be dynamic when we want to support different
wmac of SOCs. So add id_table to driver to make it extendable to more SOCs.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes random disconnect.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element

Both spurChans arrays in modalHeader5G and modalHeader2G have 5 elements,
AR_EEPROM_MODAL_SPURS is defined 5. So unless a break occurs, in the
last iteration (i=5) we tried to access spurChansPtr[5] before testing
whether i was within bounds. Fix this.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update Tx gain 23 for all tx gain table.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.

The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.

The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.

On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is nowhere used.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This does not seems to be used anywhere so remove it.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not used anywhere and seems pointless
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's easier to read and it slightly decreases code size
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stuck beacon detection is supposed to trigger when 9 consecutive beacons
could not be sent by the hardware. When the driver runs only one active
AP mode interface, it still configures the hardware beacon timer for
4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection
to be reset if ath9k_hw_stoptxdma clears the stuck frames between
SWBA intervals.
Fix this by not resetting the missed beacon count for empty slots and
multiplying the threshold not by the maximum number of beacon slots
but by the configured number of beacon interfaces.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>