The Tegra124 clock DT binding currently provides 3 clocks that don't
actually exist; 2 for NAND and one for UART5/UARTE. Delete these. While
this is technically an incompatible DT ABI change, nothing could have
used these clock IDs for anything practical, since the HW doesn't exist.

Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The Tegra124 clock driver currently provides 3 clocks that don't actually
exist; 2 for NAND and one for UART5/UARTE. Delete these.

Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.

Cc: <stable@vger.kernel.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.

* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix GPMC remap for devices using an offset
  ARM: OMAP2+: Fix oops for GPMC free
  ARM: dts: Add support for the BeagleBoard xM A/B
  ARM: dts: Grammar /that will/it will/
  ARM: dts: Grammar /is uses/ is used/
  ARM: OMAP2+: Fix config name for USB3 PHY
  ARM: dts: am335x: update USB DT references
  ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
  ARM: AM335X: EVM: fix pinmux documentation in devicetree
  ARM: OMAP2+: N900: remove omapdss init for DT boot
  ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
  ARM: dts: omap5: Add clocks to USB3 PHY node
  ARM: OMAP2+: hwmod: fix missing braces in _init()
  ARM: AM43xx: fix dpll init in bypass mode
  ARM: OMAP3: hwmod data: Correct clock domains for USB modules
  ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes

This is a patch set for some ST-Ericsson devices:
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500

* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: configure for CW1200 WLAN chip
  ARM: ux500: configure in sensors
  ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
  ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
  ARM: ux500: update defconfig
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-fixes-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Renesas ARM Based SoC Fixes Updates for v3.15

r8a7791 (R-Car M2) based koelsch board
* Correct renesas,gpios to renesas,groups in sd[012] pfc

8a7790 (R-Car H2) based lager board
* Correct SND_SOC_DAIFMT_CBx_CFx flags

r8a7740 (R-Mobile A1) SoC
* Drop address cells from GIC node

r8a7740 (R-Mobile A1) based Armadillo800 EVA board
* Correct SND_SOC_DAIFMT_CBx_CFx flags

sh73a0 (SH-Mobile AG5) SoC
* Drop address cells from GIC node

* tag 'renesas-fixes-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: koelsch: correct renesas,gpios to renesas,groups in sd[012] pfc
  ARM: shmobile: r8a7740: drop address cells from GIC node
  ARM: shmobile: sh73a0: drop address cells from GIC node
  ARM: shmobile: armadillo800eva: fixup SND_SOC_DAIFMT_CBx_CFx flags
  ARM: shmobile: lager: fixup SND_SOC_DAIFMT_CBx_CFx flags
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Fifth Round of Renesas ARM Based SoC DT Updates for v3.15

Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.

* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'v3.15-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Fixing uart-rx pull settings and a copy'n'paste error in a smp message

* tag 'v3.15-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: rockchip: fix copy'n'paste error in smp error messages
  ARM: rockchip: rk3188: enable pull-ups on UART RX pins
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 3.15:
 - A couple of dts changes for the fallout of imx-drm binding update
 - Parent DI clocks to video PLL for better HDMI support
 - PCIe interrupt mapping and GIC node fixes
 - A series of edmqmx6 board fixes
 - Other small and random fixes on imx5 and imx6 dts

* tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: i.MX6: ipu_di_sel clocks can set parent rates
  ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
  ARM: dts: imx: add required #clock-cells for fixed-clock
  ARM: dts: vybrid: drop address and size cells from GIC node
  ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
  ARM: dts: imx53: fix apparent copy/paste error
  ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
  ARM: dts: imx53-tx53: add IPU DI ports and endpoints
  ARM: dts: imx6: edmqmx6: add second STMPE
  ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
  ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
  ARM: dts: imx6: edmqmx6: Fix usbotg id pin
  ARM: dt: microsom: don't set bit 7 for ethernet mux settings
  ARM: imx6q-clk: parent lvds_gate from lvds_sel
  ARM: dts: imx: drop invalid size and address cells properties
  ARM: dts: mx5: fix wrong stmpe-ts bindings
  ARM: dts: imx53-m53evk: Fix memory region description
  ARM: dts: imx53-qsb-common: Fix memory region description
  ARM: dts: imx6: add PCIe interrupt mapping properties
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

mvebu DT fixes-non-critical (for v3.15-rc1)

 - kirkwood
    - add some missing vendor prefixes to keep checkpatch happy

 - mvebu
    - add clock ref to mdio node on 370/XP/38x

* tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: ensure the mdio node has a clock reference on Armada 38x
  ARM: mvebu: ensure the mdio node has a clock reference on Armada 370/XP
  ARM: Kirkwood: DT: Add missing vendor prefix
  ARM: Kirkwood: Fix Atmel vendor prefix
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Commit a7cbe92c ("ARM: tegra: remove tegra EMC scaling driver")
removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig
entry too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Few things were out of order:

- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
  list sorted

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: NDomenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

In commit ddb902cc (ARM: centralize common multi-platform kconfig
options), CLKSRC_OF was removed from some platforms, but not added to
ARCH_MULTIPLATFORM. Fix this.
Reported-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

I get a build warning because spear_clocksource_init() calls
clocksource_mmio_init(), but it doesn't have an __init annotation.
Fix that.
Signed-off-by: NAlex Elder <elder@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

hx4700 needs the same fix as in
9705e746
"ARM: pxa: fix various compilation problems"

Fix build errors. Initial one is:
/linux/arch/arm/mach-pxa/include/mach/hx4700.h:18:32: error:
 'PXA_NR_BUILTIN_GPIO' undeclared here (not in a function)
|  #define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.

Note that this works just fine when booted with legacy mode.

Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.

Otherwise we can get something like this:

omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300

Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If gpmc_cs_remap() fails we will get an error because we are calling
release_resource() on an uninitialized resource. Let's fix that by
checking the resource flags. And while at it, let's also make
gpmc_cs_delete_mem() use the res pointer that we already have to
avoid confusion.

Without this patch we can get the following error:

omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
(gpmc_cs_free+0x94/0xc8)
(gpmc_probe_generic_child+0x178/0x1ec)
(gpmc_probe_dt+0x1bc/0x2cc)
(gpmc_probe+0x250/0x44c)
(platform_drv_probe+0x3c/0x6c)
(really_probe+0x74/0x208)
(driver_probe_device+0x34/0x50)
(bus_for_each_drv+0x60/0x8c)
(device_attach+0x80/0xa4)
(bus_probe_device+0x88/0xb0)
(device_add+0x320/0x450)
(of_platform_device_create_pdata+0x80/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
(pdata_quirks_init+0x30/0x48)
(customize_machine+0x20/0x48)
(do_one_initcall+0x2c/0x14c)
(do_basic_setup+0x98/0xd8)
(kernel_init_freeable+0x12c/0x1e0)
(kernel_init+0x8/0xf0)
(ret_from_fork+0x14/0x2c)
Code: e1a04000 e59f0070 eb195136 e5942010 (e5923018)

Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Ntony Lindgren <tony@atomide.com>

BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge tag 'for-v3.15-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.15/fixes

OMAP hwmod and clock fixes for v3.15-rc

A few OMAP hwmod and clock fixes for v3.15-rc.  Probably the most useful
fix is the AM43xx DPLL patch.

Basic build, boot, and PM test results are here:

http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/20140411130021/

Merge branch 'fixes-v3.15-rc1'; commit '390403fd' into omap-for-v3.15/fixes

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit a70143 (drivers: phy: usb3/pipe3: Adapt pipe3 driver to Generic PHY
Framework) moved phy-omap-usb3 driver in drivers/usb/phy to drivers/phy and
also renamed the file to phy-ti-pipe3. It also renamed the config from
OMAP_USB3 to TI_PIPE3 in Kconfig. However the config name was not changed in
omap2plus_defconfig. Fixed it here.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses.  However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.

This patch corrects the references for the affected dts files.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739fa ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Do not try to initialize display for DT boot, since omapdss
is now initialized via Device Tree. Without this patch the
display subsystem does not properly come up.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The correct bit is 24 for AHCLKX.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The error emitted when mapping the pmu failed, wrongly mentions the sram.
Reported-by: NKent Borg <kentborg@borg.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.

Therefore change the rx-pin settings accordingly.

This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Route the video PLL to the display interface clocks via the di_pre_sel
and di_sel muxes by default.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.

Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The CW1200 WLAN chip driver had been in the kernel for a while,
we only need to activate it for the Ux500 properly. The latter
require some elaborative work, but in the meantime, let's make
sure we atleast compile it in.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This enables the STMicroelectronics MEMS sensors for accelerometer,
gyroscope, magnetometer and pressure that are mounted on the Ux500
models.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since there are SD-card support in u300, it's reasonable to
support partitions for block devices as default.

While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There are both (e)MMC/SD-card support in ux500, thus it's reasonable to
support partitions for block devices as default.

While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>