More LM75 updates:

 - Teach the LM75 driver to use new-style driver binding:

     * Create a second driver struct, using new-style driver binding
       methods cribbed from the legacy code.

     * Add a MODULE_DEVICE_TABLE (for "newER-style binding")

     * The legacy probe logic delegates its work to this new code.

     * The legacy driver now uses the name "lm75_legacy".

 - More careful initialization.  Chips are put into 9-bit mode so
   the current interconversion routines will never fail.

 - Save the original chip configuration, and restore it on exit.
   (Among other things, this normally turns off the mode where
   the chip is constantly sampling ... and thus saves power.)

So the new-style code should catch all chips that boards declare,
while the legacy code catches others.  This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect".  (Or else
completely eradicated...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Minor cleanup and reorg of the lm75 code.

 - Kconfig provides a larger list of lm75-compatible chips

 - A top comment now says what the driver does (!) ... as in, just
   what sort of sensor is this??

 - Section comments now delineate the various sections of the driver:
   hwmon attributes, driver binding, register access, module glue.
   One driver binding function moved out of the attribute section,
   as did the driver struct itself.

 - Minor tweaks to legacy probe logic:  correct a comment, and
   remove a pointless variable.

 - Whitespace, linelength, and comment fixes.

This patch should include no functional changes.  It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

All the *_MAX_ADDR defines are never used, so remove them. The number
of registers of each type is already expressed by the *_COUNT defines.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch fixes a voltage scaling issue for the sch311x device.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch gets rid of a couple of macros previously used for sysfs attribute
generation and manipulation. This makes the source a little bigger but a lot
more readable and maintainable. It also fixes an issue with pwm5 & pwm6
attributes not being created read-only initially.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add the rtc8564 chip entry
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix chip naming from fm3031-rtc to fm3031
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cortland Setlow pointed out a bug in ov7670.c where the result from
ov7670_read() was just being checked for !0, rather than <0.  This made me
realize that ov7670_read's semantics were rather confusing; it both fills
in 'value' with the result, and returns it.  This is goes against general
kernel convention; so rather than fixing callers, let's fix the function.

This makes ov7670_read return <0 in the case of an error, and 0 upon
success. Thus, code like:

res = ov7670_read(...);
if (!res)
	goto error;

..will work properly.
Signed-off-by: NCortland Setlow <csetlow@tower-research.com>
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I had 8250.nr_uarts=16 in the boot line of a test kernel and I had a weird
mysterious crash in sysfs.  After taking an in-depth look I realized that
CONFIG_SERIAL_8250_NR_UARTS was set to 4 and I was walking off the end of
the serial8250_ports array.

Ouch!!!

Don't let this happen to someone else.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NAlan Cox <alan@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is a bugfix for how defio handles multiple processes manipulating
the same framebuffer.

Thanks to Bernard Blackham for identifying this bug.

It occurs when two applications mmap the same framebuffer and concurrently
write to the same page.  Normally, this doesn't occur since only a single
process mmaps the framebuffer.  The symptom of the bug is that the mapping
applications will hang.  The cause is that defio incorrectly tries to add the
same page twice to the pagelist.  The solution I have is to walk the pagelist
and check for a duplicate before adding.  Since I needed to walk the pagelist,
I now also keep the pagelist in sorted order.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: Bernard Blackham <bernard@largestprime.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Coverity CID: 1356 RESOURCE_LEAK

I found a very old patch for this that was Acked but did not get applied
https://lists.linux-foundation.org/pipermail/kernel-janitors/2006-September/016362.html

There looks to be a small leak in isdn_writebuf_stub() in isdn_common.c, when
copy_from_user() returns an un-copied data length (length != 0).  The below
patch should be a minimally invasive fix.
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmailcom>
Acked-by: NKarsten Keil <kkeil@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Coverity CID: 2172 RESOURCE_LEAK

When pool_allocate() tries to enlarge a packet, if it can not allocate enough
memory, it returns NULL without first freeing the old packet.

This patch just frees the packet first.
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmail.com>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There's a fault on the FC controllers that makes them not respond
correctly to MSI.  The SPI controllers are fine, but are likely to be
onboard on older motherboards which don't handle MSI correctly, so
default both these cases to disabled.  Enable by setting the module
parameter mpt_msi_enable=1.

For the SAS case, enable MSI by default, but it can be disabled by
setting the module parameter mpt_msi_enable=0.

Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch corrects the handling of write operations to the IPMI watchdog
to work as intended by returning the number of characters actually
processed. Without this patch, an "echo V >/dev/watchdog" enables the
watchdog if IPMI is providing the watchdog function.
Signed-off-by: NMark Rustad <MRustad@gmail.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Currently, ipr does not support HDIO_GET_IDENTITY to SATA devices.
An oops occurs if userspace attempts to send the command. Since hald
issues the command, ensure we fail the ioctl in ipr. This is a
temporary solution to the oops. Once the ipr libata EH conversion
is upstream, ipr will fully support HDIO_GET_IDENTITY.
Tested-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The problem is introduced by commit
664d080c.

acpi_evaluate_integer is a sleeping function,
and it should not be called with spin_lock_irqsave.
https://bugzilla.redhat.com/show_bug.cgi?id=451399Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This enables short 40-wire detection for my laptop thus
enabling UDMA/100.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration.  This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled.  On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.

This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The IRQ rate reported back by the RTC is incorrect when HPET is enabled.

Newer hardware that has HPET to emulate the legacy RTC device gets this value
wrong since after it sets the rate, it returns before setting the variable
used to report the IRQ rate back to users of the device -- so the set rate and
the reported rate get out of sync.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch was created by

	git grep -E -l 'Rus(el|s?e)l King' | xargs -r -t perl -p -i -e 's/Rus(el|s?e)l King/Russell King/g'
Signed-off-by: NUwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Most-Definitely-Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix RapidIO device reference counting.
Signed-of-by: NEugene Surovegin <ebs@ebshome.net>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds Intel TPM TIS device HID:  ICO0102
Signed-off-by: NMarcin Obara <marcin_obara@users.sourceforge.net>
Acked-by: NMarcel Selhorst <tpm@selhorst.net>
Acked-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The scenario goes like this. App stops reading from tun/tap.
TX queue gets full and driver does netif_stop_queue().
App closes fd and TX queue gets flushed as part of the cleanup.
Next time the app opens tun/tap and starts reading from it but
the xoff state is not cleared. We're stuck.
Normally xoff state is cleared when netdev is brought up. But
in the case of persistent devices this happens only during
initial setup.

The fix is trivial. If device is already up when an app opens
it we clear xoff state and that gets things moving again.
Signed-off-by: NMax Krasnyansky <maxk@qualcomm.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the dubious attempt to prefer 'compute' over 'read'.  Not only is it
wrong given commit c337869d (md: do not compute parity unless it is on a failed
drive), but it can trigger a BUG_ON in handle_parity_checks5().

Cc: <stable@kernel.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeil Brown <neilb@suse.de>

Fixing unaligned memory access on the blackfin architecture.
Signed-off-by: NIhar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a mesh or ad-hoc interface is brought up and later it is replaced
by managed interface, the managed interface will keep transmitting
the beacons that were configured for the former interface. This patch
fixes that behaviour.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.

This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The change to iwch_provider.c in commit f4e91eb4 ("IB: convert struct
class_device to struct device") undid the fix done in commit 7f049f2f
("RDMA/cxgb3: Hold rtnl_lock() around ethtool get_drvinfo call").  It
removed the calls to rtnl_lock() that serialized the iw_cxgb3 ethtool
ops calls into the cxgb3 driver.  This locking is needed to avoid
messing up the internal state of the cxgb3 driver.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

On 2.6.26-rc9, the commit 05946bce
("fsl_diu_fb: fix build with CONFIG_PM=y, plus fix some warnings")
breaks its previous fix f969c567
("fsl-diu-db: compile fix")

This patch reverts the broken part.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver uses completely bogus rounding formula for calculating period from
the IDECLK frequency which gives one-off period values (e.g. 11 ns with 100 MHz
IDECLK) which in turn can lead to overclocked IDE transfer timings.  Actually,
rounding is just wrong in this case, so use a mere division for a safe result.

While at it, also:

- give 'ide_palm_clk' variable a more suitable name;

- get rid of the useless 'ideclkp' variable;

- drop the LISP stype 'p' postfix from the 'clkp' variable's name. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: mcherkashin@ru.mvista.com
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add __ide_default_irq() inline helper and use it instead of
ide_default_irq() in ide-probe.c and ns87415.c (all host drivers
except IDE PCI ones always setup hwif->irq so it is enough to
check only for I/O bases 0x1f0 and 0x170).

This fixes post-2.6.25 regression since ide_default_irq()
define could shadow ide_default_irq() inline.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The problem here is that if the ioc faults too early in the bring up
sequence (as it usually does for an irq routing problem), ioc_reset gets
called before the scsi host is even allocated.  This causes an oops when
it later schedules a renegotiation.  Fix this by checking ioc->sh before
trying to renegotiate.

Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

HP OmniBook 500's DSDT code changes the HID of the FIR device from
NSC6001 to HWPC224 when run under an "NT" operating system. Add the
new ID to the pnp device id table.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. dma should be freed when dma2 request fail.
2. dma2 should be freed too when device close.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On embedded devices we must not route the interrupts through
the PCI core, if our host-bus is not PCI.
Reported-by: NSteve Brown <sbrown@cortland.com>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I would like to inform you of our zd1211 based usb wifi adapter (AirTies
WUS-201), which works with the zd1211rw driver with the following device
id definition.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Coverity CID: 2265 NEGATIVE_RETURNS

"rate" is of an unsigned type, and the code requires a signed type.
The following patch makes it so.
Signed-off-by: NDarren Jenkins <darrenrjenkins@gmailcom>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>