When num-slots is lower than 1, it's right that should be returned -ENODEV.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>

The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.

Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.

So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a

[    4.991109] ------------[ cut here ]------------
[    4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[    4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM

because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.

Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>

This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
   "ENOSYS means 'invalid syscall nr' and nothing else"
- split lines whose length is greater than 80 characters
- avoid quoted string split across lines
- use min_t instead of min, to fix warning message:
   "min() should probably be min_t(int, cnt, host->part_buf_count)"
- fix missing a blank line after declarations
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>

As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.

On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.

In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.

Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.

What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>

Some Sandisk cards(such as "SDMB-32" and "SDM032" cards)
can't support CMD23, and would generate CMD timeout. So add
FIX-UP for these two types Sandisk cards.

Error log:
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Before 5b83b223 the driver was hard coding the wakeup irq to
be active low. The generic pm wakeirq does not override the active
high/low parameter, hence it must be specified correctly in the
device tree.
Mind that SDIO IRQ is active low as defined in the SDIO specification
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It's excessive to use prefix for the parameters when you do
modprobe mmc-block mmcblk.perdev_minors=16

Make this available only for built-in case.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

See Documentation/DMA-API.txt - Part Id
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

adding SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,SDHCI_QUIRK2_PRESET_VALUE_BROKEN
flags for arasan sdhc.
Signed-off-by: NSuneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.
Signed-off-by: NSuneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Switch over pxamci to dmaengine. This prepares the devicetree full
support of pxamci.

This was successfully tested on a PXA3xx board, as well as PXA27x.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
[adapted to pxa-dma]
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "A smallish batch of fixes, a little more than expected this late, but
  all fixes are contained to their platforms and seem reasonably low
  risk:

   - a somewhat large SMP fix for ux500 that still seemed warranted to
     include here
   - OMAP DT fixes for pbias regulator specification that broke due to
     some DT reshuffling
   - PCIe IRQ routing bugfix for i.MX
   - networking fixes for keystone
   - runtime PM for OMAP GPMC
   - a couple of error path bug fixes for exynos"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
  ARM: dts: keystone: fix the clock node for mdio
  memory: omap-gpmc: Don't try to save uninitialized GPMC context
  ARM: imx6: correct i.MX6 PCIe interrupt routing
  ARM: ux500: add an SMP enablement type and move cpu nodes
  ARM: dts: dra7: Fix broken pbias device creation
  ARM: dts: OMAP5: Fix broken pbias device creation
  ARM: dts: OMAP4: Fix broken pbias device creation
  ARM: dts: omap243x: Fix broken pbias device creation
  ARM: EXYNOS: fix double of_node_put() on error path
  ARM: EXYNOS: Fix potentian kfree() of ro memory

Pull MIPS bugfix from Ralf Baechle:
 "Only a single MIPS fix - the math when invoking syscall_trace_enter
  was wrong"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix seccomp syscall argument for MIPS64

Merge x86 fixes from Ingo Molnar:
 "Two followup fixes related to the previous LDT fix"

Also applied a further FPU emulation fix from Andy Lutomirski to the
branch before actually merging it.

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
  x86/ldt: Further fix FPU emulation
  x86/ldt: Correct FPU emulation access to LDT
  x86/ldt: Correct LDT access in single stepping logic

The previous fix confused a selector with a segment prefix.  Fix it.

Compile-tested only.

Cc: stable@vger.kernel.org
Cc: Juergen Gross <jgross@suse.com>
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Fixes: 4809146b ("x86/ldt: Correct FPU emulation access to LDT")
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fuse_dev_ioctl() performed fuse_get_dev() on a user-supplied fd,
leading to a type confusion issue. Fix it by checking file->f_op.
Signed-off-by: NJann Horn <jann@thejh.net>
Acked-by: NMiklos Szeredi <miklos@szeredi.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes

ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+

These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are broken without these two fixes.

* tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
  ARM: dts: keystone: fix the clock node for mdio
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.

Fixes: 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)")
Cc: <stable@vger.kernel.org> # 3.15+
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Pull SCSI fixes from James Bottomley:
 "This has two libfc fixes for bugs causing rare crashes, one iscsi fix
  for a potential hang on shutdown, and a fix for an I/O blocksize issue
  which caused a regression"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  sd: Fix maximum I/O size for BLOCK_PC requests
  libfc: Fix fc_fcp_cleanup_each_cmd()
  libfc: Fix fc_exch_recv_req() error path
  libiscsi: Fix host busy blocking during connection teardown

Pull KVM fixes from Paolo Bonzini:
 "Just two very small & simple patches"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Use adjustment in guest cycles when handling MSR_IA32_TSC_ADJUST
  KVM: x86: zero IDT limit on entry to SMM

Merge fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  Update maintainers for DRM STI driver
  mm: cma: mark cma_bitmap_maxno() inline in header
  zram: fix pool name truncation
  memory-hotplug: fix wrong edge when hot add a new node
  .mailmap: Andrey Ryabinin has moved
  ipc/sem.c: update/correct memory barriers
  mm/hwpoison: fix panic due to split huge zero page
  ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()
  ipc,sem: fix use after free on IPC_RMID after a task using same semaphore set exits
  mm/hwpoison: fix fail isolate hugetlbfs page w/ refcount held
  mm/hwpoison: fix page refcount of unknown non LRU page

Pull clock fix from Stephen Boyd:
 "A one-liner for a regression found in the PXA clock driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: pxa: pxa3xx: fix CKEN register access

Add Vincent Abriou and myself as maintainers.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cma_bitmap_maxno() was marked as static and not static inline, which can
cause warnings about this function not being used if this file is included
in a file that does not call that function, and violates the conventions
used elsewhere.  The two options are to move the function implementation
back to mm/cma.c or make it inline here, and it's simple enough for the
latter to make sense.
Signed-off-by: NGregory Fong <gregory.0xf0@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

zram_meta_alloc() constructs a pool name for zs_create_pool() call as

    snprintf(pool_name, sizeof(pool_name), "zram%d", device_id);

However, it defines pool name buffer to be only 8 bytes long (minus
trailing zero), which means that we can have only 1000 pool names: zram0
-- zram999.

With CONFIG_ZSMALLOC_STAT enabled an attempt to create a device zram1000
can fail if device zram100 already exists, because snprintf() will
truncate new pool name to zram100 and pass it debugfs_create_dir(),
causing:

  debugfs dir <zram100> creation failed
  zram: Error creating memory pool

... and so on.

Fix it by passing zram->disk->disk_name to zram_meta_alloc() instead of
divice_id.  We construct zram%d name earlier and keep it as a ->disk_name,
no need to snprintf() it again.
Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we add a new node, the edge of memory may be wrong.

e.g. system has 4 nodes, and node3 is movable, node3 mem:[24G-32G],

1. hotremove the node3,
2. then hotadd node3 with a part of memory, mem:[26G-30G],
3. call hotadd_new_pgdat()
        free_area_init_node()
                get_pfn_range_for_nid()
4. it will return wrong start_pfn and end_pfn, because we have not
update the memblock.

This patch also fixes a BUG_ON during hot-addition, please see
http://marc.info/?l=linux-kernel&m=142961156129456&w=2Signed-off-by: NXishi Qiu <qiuxishi@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update my email address.
Signed-off-by: NAndrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sem_lock() did not properly pair memory barriers:

!spin_is_locked() and spin_unlock_wait() are both only control barriers.
The code needs an acquire barrier, otherwise the cpu might perform read
operations before the lock test.

As no primitive exists inside <include/spinlock.h> and since it seems
noone wants another primitive, the code creates a local primitive within
ipc/sem.c.

With regards to -stable:

The change of sem_wait_array() is a bugfix, the change to sem_lock() is a
nop (just a preprocessor redefinition to improve the readability).  The
bugfix is necessary for all kernels that use sem_wait_array() (i.e.:
starting from 3.10).
Signed-off-by: NManfred Spraul <manfred@colorfullife.com>
Reported-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Kirill Tkhai <ktkhai@parallels.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: <stable@vger.kernel.org>	[3.10+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bug:

  ------------[ cut here ]------------
  kernel BUG at mm/huge_memory.c:1957!
  invalid opcode: 0000 [#1] SMP
  Modules linked in: snd_hda_codec_hdmi i915 rpcsec_gss_krb5 snd_hda_codec_realtek snd_hda_codec_generic nfsv4 dns_re
  CPU: 2 PID: 2576 Comm: test_huge Not tainted 4.2.0-rc5-mm1+ #27
  Hardware name: Dell Inc. OptiPlex 7020/0F5C5X, BIOS A03 01/08/2015
  task: ffff880204e3d600 ti: ffff8800db16c000 task.ti: ffff8800db16c000
  RIP: split_huge_page_to_list+0xdb/0x120
  Call Trace:
    memory_failure+0x32e/0x7c0
    madvise_hwpoison+0x8b/0x160
    SyS_madvise+0x40/0x240
    ? do_page_fault+0x37/0x90
    entry_SYSCALL_64_fastpath+0x12/0x71
  Code: ff f0 41 ff 4c 24 30 74 0d 31 c0 48 83 c4 08 5b 41 5c 41 5d c9 c3 4c 89 e7 e8 e2 58 fd ff 48 83 c4 08 31 c0
  RIP  split_huge_page_to_list+0xdb/0x120
   RSP <ffff8800db16fde8>
  ---[ end trace aee7ce0df8e44076 ]---

Testcase:

    #define _GNU_SOURCE
    #include <stdlib.h>
    #include <stdio.h>
    #include <sys/mman.h>
    #include <unistd.h>
    #include <fcntl.h>
    #include <sys/types.h>
    #include <errno.h>
    #include <string.h>

    #define MB 1024*1024

    int main(void)
    {
            char *mem;

            posix_memalign((void **)&mem, 2 * MB, 200 * MB);

            madvise(mem, 200 * MB, MADV_HWPOISON);

            free(mem);

            return 0;
    }

Huge zero page is allocated if page fault w/o FAULT_FLAG_WRITE flag.
The get_user_pages_fast() which called in madvise_hwpoison() will get
huge zero page if the page is not allocated before.  Huge zero page is a
tranparent huge page, however, it is not an anonymous page.
memory_failure will split the huge zero page and trigger
BUG_ON(is_huge_zero_page(page));

After commit 98ed2b00 ("mm/memory-failure: give up error handling
for non-tail-refcounted thp"), memory_failure will not catch non anon
thp from madvise_hwpoison path and this bug occur.

Fix it by catching non anon thp in memory_failure in order to not split
huge zero page in madvise_hwpoison path.

After this patch:

  Injecting memory failure for page 0x202800 at 0x7fd8ae800000
  MCE: 0x202800: non anonymous thp
  [...]

[akpm@linux-foundation.org: remove second split, per Wanpeng]
Signed-off-by: NWanpeng Li <wanpeng.li@hotmail.com>
Acked-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After we acquire the sma->sem_perm lock in exit_sem(), we are protected
against a racing IPC_RMID operation.  Also at that point, we are the last
user of sem_undo_list.  Therefore it isn't required that we acquire or use
ulp->lock.
Signed-off-by: NHerton R. Krzesinski <herton@redhat.com>
Acked-by: NManfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Rafael Aquini <aquini@redhat.com>
CC: Aristeu Rozanski <aris@redhat.com>
Cc: David Jeffery <djeffery@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>