Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_params.c file now only handles Ethtool functionality
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slight refactoring of duplicated wait for idle checks
Spelling fix
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: jie.yang@atheros.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should not be stopping the subqueues in cpmac_end_xmit
but rather test the status of them. Replace the calls to
netif_subqueue_stop by __netif_subqueue_stopped. This
fixes an unrecoverable exception from happening when
running the driver.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the unused variables in
cpmac_hw_error, cpmac_tx_timeout and cpmac_probe.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:

  can@3,100 {
  	compatible = "nxp,sja1000";
  	reg = <3 0x100 0x80>;
  	interrupts = <2 0>;
  	interrupt-parent = <&mpic>;
  	nxp,external-clock-frequency = <16000000>;
  };

See also Documentation/powerpc/dts-bindings/can/sja1000.txt.

CC: devicetree-discuss@ozlabs.org
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As discussed on the netdev mailing list, the member "base_addr" of
"struct net_device" should not be (mis)used to store the virtual
address to the SJA1000 register area. According to David Miller,
it's only use is to allow ISA and similar primitive bus devices to
have their I/O ports changed via ifconfig. The virtual address is
now stored in the private data structure of the SJA1000 device and
the callback functions use "struct sja1000_priv" instead of the
unneeded "struct net_device".
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a few errors sneaked into the initial version of the
device driver interface.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Warning messages coming from rtl8150 driver can flood the console
and make a DTV/set-top-box unable to decode video/audio frames.

'Pegasus' driver handles this situation similarly, preventing this
from happening there.

It happens with a low cost BCM MIPS embedded platform, whenever
timeout errors were coming from usbnet device, making platform
unusable for viewer watching.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add FEC support for MX35 processor.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds power management suspend/resume hooks for irda-usb.
Signed-off-by: NTadashi Abe <tabe@mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac8390: use printk MAC address format
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).

I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.

The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c               |   13 +--
 drivers/net/e1000/e1000_main.c   |   24 +++--
 drivers/net/ixgbe/ixgbe_common.c |   14 ++--
 drivers/net/ixgbe/ixgbe_common.h |    4 +-
 drivers/net/ixgbe/ixgbe_main.c   |    6 +-
 drivers/net/ixgbe/ixgbe_type.h   |    4 +-
 drivers/net/macvlan.c            |   11 +-
 drivers/net/mv643xx_eth.c        |   11 +-
 drivers/net/niu.c                |    7 +-
 drivers/net/virtio_net.c         |    7 +-
 drivers/s390/net/qeth_l2_main.c  |    6 +-
 drivers/scsi/fcoe/fcoe.c         |   16 ++--
 include/linux/netdevice.h        |   18 ++--
 net/8021q/vlan.c                 |    4 +-
 net/8021q/vlan_dev.c             |   10 +-
 net/core/dev.c                   |  195 +++++++++++++++++++++++++++-----------
 net/dsa/slave.c                  |   10 +-
 net/packet/af_packet.c           |    4 +-
 18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the Aquantia AQ1002 10G-BaseT phy.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the AEL2020 phy.
Add PCI IDs of the boards using this phy.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cxgb3 no longer advertizes LLTX.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we register the MII bus to the platfrom bus, the Distributed Switch
Architecture can hook in transparently.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Remove dead long delay
- Use proper defines
- Remove broken implementation of the TX DMA Data Alignment TXDWA feature
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Writes to the DMA descriptors may sit in the internal Blackfin data buffers
and not actually be available when the DMA engine goes to fetch them.  This
does not typically happen, but when dealing with short/fast packets such as
UDP and polling KGDB, this occurs much more frequently.  Same goes for
heavy loads as seen by netperf tests or large scp transfers.  So force the
buffers to drain with SSYNC otherwise we get random malformed packets.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IRQ used by the Blackfin EMAC is internal to the peripheral and cannot
be used to generate any other interrupt, so there is no point in marking it
as IRQF_SHARED.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to release skb->dst, its now done by core network.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the korina driver poll the media
for link change. This is actually required on
Mikrotik RB532 (not RB532A) for korina to
operate properly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:

/* Backwards compat, remove in 2.7.x */
#define dma_sync_single		dma_sync_single_for_cpu
#define dma_sync_sg		dma_sync_sg_for_cpu
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.

Exceptions are NETIF_F_LLTX drivers
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Followup of commits 9d21493b
and 08baf561
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.

Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.

If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.

To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is requested (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

From a fix by Cindy H Kao:

  Block size has to be set before sending IOE enable because the
  firmware reads the block size register before it reads IOE register.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Functions i2400m_report_tlv*() are only called from
i2400m_report_hook(), called in a workqueue by
i2400m_report_hook_work(). The scheduler checks for device readiness
before scheduling.

Added an extra check for readiness in i2400m_report_hook_work(), which
makes all the checks down the line redundant.

Obviously the device state could change in the middle, but error
handling would take care of that.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

i2400m_report_state_hook() is going to get messier as we add handling
code.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user',
the driver will echo to user space all the commands being sent to the
device from user space, along with the responses.

However, this only helps with the commands being sent from user space;
with this patch, the trace hook is moved to i2400m_msg_to_dev(), which
is the single access point for running commands to the device (both by
user space and the kernel driver). This allows better debugging by
having a complete stream of commands/acks and reports.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

When commands are sent from user space, trace both the command sent
and the answer received over the "echo" pipe instead of over the
"trace" pipe when command tracing is enabled. As well, when the device
sends a reports/indications, send it over the "echo" pipe.

The "trace" pipe is used by the device to send firmware traces;
gets confusing. Another named pipe makes it easier to split debug
information.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

The WiMAX i2400m driver needs to generate a fake source MAC address to
fake an ethernet header (for destination, the card's MAC is
used). This is the source of the packet, which is the basestation it
came from. The basestation's mac address is not usable for this, as it
uses its own namespace and it is not always available.

Currently the fake source MAC address was being set to all zeros,
which was causing trouble with bridging.

Use random_ether_addr() to generate a proper one that creates no
trouble.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

First of all, it exposes the SKB list implementation.

Second of all it's not needed.  If we get called here, we
successfully enqueued the URB with the linked SKB and
such a completion only gets called one time on such an
SKB.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This eliminates explicit references to the SKB list handling
implementation.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use struct net_device_stats provided in struct net_device instead of
private ones.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the not-that-useful message in the
r6040_timer which prints the PHY status. Instead
replace it with a call to mii_check_media which will
update the link status and print it on startup.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>