Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 03 10月, 2017 10 次提交
  3. 01 10月, 2017 1 次提交
  5. 30 9月, 2017 2 次提交
  7. 27 9月, 2017 1 次提交
  9. 26 9月, 2017 20 次提交
  11. 25 9月, 2017 6 次提交
    • S
      block: fix a crash caused by wrong API · f5c156c4
      由 Shaohua Li 提交于 
      part_stat_show takes a part device not a disk, so we should use
part_to_disk.

Fixes: d62e26b3("block: pass in queue to inflight accounting")
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: NShaohua Li <shli@fb.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      f5c156c4
    • L
      fs: Fix page cache inconsistency when mixing buffered and AIO DIO · 332391a9
      由 Lukas Czerner 提交于 
      Currently when mixing buffered reads and asynchronous direct writes it
is possible to end up with the situation where we have stale data in the
page cache while the new data is already written to disk. This is
permanent until the affected pages are flushed away. Despite the fact
that mixing buffered and direct IO is ill-advised it does pose a thread
for a data integrity, is unexpected and should be fixed.

Fix this by deferring completion of asynchronous direct writes to a
process context in the case that there are mapped pages to be found in
the inode. Later before the completion in dio_complete() invalidate
the pages in question. This ensures that after the completion the pages
in the written area are either unmapped, or populated with up-to-date
data. Also do the same for the iomap case which uses
iomap_dio_complete() instead.

This has a side effect of deferring the completion to a process context
for every AIO DIO that happens on inode that has pages mapped. However
since the consensus is that this is ill-advised practice the performance
implication should not be a problem.

This was based on proposal from Jeff Moyer, thanks!
Reviewed-by: NJan Kara <jack@suse.cz>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NLukas Czerner <lczerner@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      332391a9
    • J
      nvmet: implement valid sqhd values in completions · bb1cc747
      由 James Smart 提交于 
      To support sqhd, for initiators that are following the spec and
paying attention to sqhd vs their sqtail values:

- add sqhd to struct nvmet_sq
- initialize sqhd to 0 in nvmet_sq_setup
- rather than propagate the 0's-based qsize value from the connect message
  which requires a +1 in every sqhd update, and as nothing else references
  it, convert to 1's-based value in nvmt_sq/cq_setup() calls.
- validate connect message sqsize being non-zero per spec.
- updated assign sqhd for every completion that goes back.

Also remove handling the NULL sq case in __nvmet_req_complete, as it can't
happen with the current code.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      bb1cc747
    • G
      nvme-fabrics: Allow 0 as KATO value · 8edd11c9
      由 Guilherme G. Piccoli 提交于 
      Currently, driver code allows user to set 0 as KATO
(Keep Alive TimeOut), but this is not being respected.
This patch enforces the expected behavior.
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      8edd11c9
    • J
      nvme: allow timed-out ios to retry · 0951338d
      由 James Smart 提交于 
      Currently the nvme_req_needs_retry() applies several checks to see if
a retry is allowed. On of those is whether the current time has exceeded
the start time of the io plus the timeout length. This check, if an io
times out, means there is never a retry allowed for the io. Which means
applications see the io failure.

Remove this check and allow the io to timeout, like it does on other
protocols, and retries to be made.

On the FC transport, a frame can be lost for an individual io, and there
may be no other errors that escalate for the connection/association.
The io will timeout, which causes the transport to escalate into creating
a new association, but the io that timed out, due to this retry logic, has
already failed back to the application and things are hosed.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      0951338d
    • J
      nvme: stop aer posting if controller state not live · cd48282c
      由 James Smart 提交于 
      If an nvme async_event command completes, in most cases, a new
async event is posted. However, if the controller enters a
resetting or reconnecting state, there is nothing to block the
scheduled work element from posting the async event again. Nor are
there calls from the transport to stop async events when an
association dies.

In the case of FC, where the association is torn down, the aer must
be aborted on the FC link and completes through the normal job
completion path. Thus the terminated async event ends up being
rescheduled even though the controller isn't in a valid state for
the aer, and the reposting gets the transport into a partially torn
down data structure.

It's possible to hit the scenario on rdma, although much less likely
due to an aer completing right as the association is terminated and
as the association teardown reclaims the blk requests via
nvme_cancel_request() so its immediate, not a link-related action
like on FC.

Fix by putting controller state checks in both the async event
completion routine where it schedules the async event and in the
async event work routine before it calls into the transport. It's
effectively a "stop_async_events()" behavior.  The transport, when
it creates a new association with the subsystem will transition
the state back to live and is already restarting the async event
posting.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
[hch: remove taking a lock over reading the controller state]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
      cd48282c