This manufacturer ID is used under the name Spansion.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The Kconfig help on "Flash cmd/query data swapping" still mentions
LART_ENDIAN_BYTE. That option used to be relevant for setting
CONFIG_MTD_CFI_LART_BIT_SWAP. That option and macro got both removed in
v2.4.11-pre4. So, although LART endianness sounds intriguing, that part
of the help text can be removed.

And, while we're touching this choice, move the help text up one level.
Currently it's available under the "NO" option, while it's relevant for
all three options.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds support for the SLC NAND controller inside the LPC32xx SoC.

[dwmw2: 21st century pedantry]
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.

Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
  1. add return 'int' value for 'write_page' function.
  2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
  3. add code to test the return value, and if negative, indicate an
  error happend when write page with ECC.
  4. fix the compile warning in all impacted nand flash driver.

Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch moves hw ecc initialization code to one function.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The code responsible for reading the version of the mirror bbt was
incorrectly using the descriptor of the main bbt.

Pass the mirror bbt descriptor to 'scan_read_raw' when reading the
version of the mirror bbt.
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org [v2.6.37+]
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This adds snippets to the i.MX51/53 devicetrees for the nand
flash controller.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The only relevant change between i.MX51 and i.MX53 is that
a bitfield is shifted one bit to the left.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The i.MX v3 nand controller (i.MX5) needs two memory resources.
Traditionally we have the AXI resource first. For sorting in this
driver into the devicetree it feels much more natural to have the
IP resource first. This patch swaps the ordering of these two
resources.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

To make the error path simpler and to make subsequent patches
easier.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Previously the remove method was looping and removing all chips,
which is obviously not the right thing to do — left over from when
the driver was organized differently and that was the remove method for
the entire controller.  This would result in bad things happening if
you have more than one NAND chip, and remove the module.

This also fixes priv->dev to properly point to the chip's device rather than
the controller's.  Until now priv->dev was only used for error/debug prints
(and it's an improvement there), so this shouldn't break anything.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Adds JEDEC ID for the 1.8V version of WinBond w25q32.
Signed-off-by: NFederico Fuga <fuga@studiofuga.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Prepare the clock before enabling it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This option was never used and isn't currently used.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Eon's new NAND flash: EN27LN1G08.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This is a clean-up patch which removes the own pseudo-random numbers generator
from the speed- and stress-tests and makes them use the 'random32()' generator
instead.

[dwmw2: Merge later fix for negative offsets]
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In hardware ecc mode, the flctl now writes and reads the oob data
provided by the user. Additionally the ECC is now returned in normal
page reads, not only when using the explicit NAND_CMD_READOOB command.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

There are multiple reasons for a rewrite:
 - a race exists: when _4ECCEND is set, _4ECCFA may become true too
   meanwhile, which is lost and a non-correctable error is treated as
   correctable.
 - the ECC statistics don't get properly propagated to the base code.
 - empty pages would get marked as corrupted

The rewrite resolves the issues and I hope it gives a more explicit
code flow structure.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When we use hardware ecc, the flctl is run in so-called "sector access
mode". We can bundle 4 sector accesses when using 2KiB page sizes to read
a whole page at once and speed up things.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

As the equation mtd->writesize == eccsteps * eccsize holds, we can
simplify the code. The second loop of the 1st hunk is never entered,
so we delete it.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The flctl uses 10 bytes ECC data for every 512 bytes sector. This patch
makes the controller write all 40 bytes instead of 10 bytes only.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The flctl hardware has changed and a new OOB layout must be adapted for
2KiB page size NAND chips when using hardware ECC.
The related bit fields ECCPOS[0-2] are gone — the bits are marked as
reserved now in the datasheet. As there are no official users of the
hardware ECC so far, they are completely removed.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

When the data transfer between the controller and the NAND chip fails,
we now get notified.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add the unmapping for the error case and for the driver removal.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch is simply an added warning in the comments. Ideally, this patch
need not be merged, but rather, a developer will write a proper solution
that can use the ecc.read_oob_raw and ecc.write_oob_raw interfaces.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We can clean up the loop logic a bit, here. This refactoring was enabled
in part by:

 Commit bb4a0986 [mtdoops: clean-up new MTD API usage]
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

mtd_read_oob() will be expanded a little, so don't leave it in the header
as a static inline function.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We don't need to open code the divide function, just use div_u64 that
already exists and do the same job. While this is a straightforward
clean up, there is more to that, the real motivation for this.

While building on a cross compiling environment in armel, using gcc
4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5), I was getting the following build
error:

ERROR: "__aeabi_uldivmod" [drivers/mtd/nand/nandsim.ko] undefined!

After investigating with objdump and hand built assembly version
generated with the compiler, I narrowed __aeabi_uldivmod as being
generated from the divide function. When nandsim.c is built with
-fno-inline-functions-called-once, that happens when
CONFIG_DEBUG_SECTION_MISMATCH is enabled, the do_div optimization in
arch/arm/include/asm/div64.h doesn't work as expected with the open
coded divide function: even if the do_div we are using doesn't have a
constant divisor, the compiler still includes the else parts of the
optimized do_div macro, and translates the divisions there to use
__aeabi_uldivmod, instead of only calling __do_div_asm -> __do_div64 and
optimizing/removing everything else out.

So to reproduce, gcc 4.6 plus CONFIG_DEBUG_SECTION_MISMATCH=y and
CONFIG_MTD_NAND_NANDSIM=m should do it, building on armel.

After this change, the compiler does the intended thing even with
-fno-inline-functions-called-once, and optimizes out as expected the
constant handling in the optimized do_div on arm. As this also avoids a
build issue, I'm marking for Stable, as I think is applicable for this
case.
Signed-off-by: NHerton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: stable@vger.kernel.org
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The -EUCLEAN return value applies to mtd_read_oob() as well as mtd_read(), but
only mtd_read() was mentioned in the blurd on bitflip_threshold in the ABI
documentation.
Signed-off-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The gpmi-nand driver uses virt_addr_valid() to check whether a buffer
is suitable for dma. If it's not, a driver allocated buffer is used
instead. Then after a page read the driver allocated buffer must be
copied to the user supplied buffer. This does not happen since commit
7725cc85.

This patch fixes the issue. The bug is encountered with UBI which uses a
vmalloced buffer for the volume table.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: snijsure@grid-net.com
Acked-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The following commit changes the function used to copy from/to
the hardware buffer to memcpy_[from|to]io. This does not work
since the hardware cannot handle the byte accesses used by these
functions. Instead of reverting this patch introduce 32bit
correspondents of these functions.

| commit 5775ba36ea9c760c2d7e697dac04f2f7fc95aa62
| Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
| Date:   Tue Apr 24 10:05:22 2012 +0200
|
|    mtd: mxc_nand: fix several sparse warnings about incorrect address space
|
|     Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|     Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The intent here was clearly to set result to true if the 0x40000000 flag
was set.  But instead there was a | vs & typo and we always set result
to true.

Artem: check the spec at
wiki.laptop.org/images/5/5c/88ALP01_Datasheet_July_2007.pdf
and this fix looks correct.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

As of edbc4540 [mtd: driver _read() returns max_bitflips; mtd_read()
returns -EUCLEAN], 'mtd->bitflip_threshold' must be set for mtd devices
having ECC, prior any 'mtd_read()' call.
Otherwise, 'mtd_read()' will falsely return -EUCLEAN.

Normally, 'mtd->bitflip_threshold' is initialized when the MTD is added.

However, this is too late for NAND MTDs, as 'scan_bbt()' is invoked
prior the existing initialization of 'mtd->bitflip_threshold'.

This is a problem since 'scan_bbt()' calls 'mtd_read()', in the case
of a flash-based bad block table.
It resulted in a falsely reported bitflips indication during BBT read,
which lead to constant scrubbing of the flash BBT blocks.

Initialize 'mtd->bitflip_threshold' to its default value (if not already
set by the driver), prior to invocation of 'scan_bbt()'.
Reported-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

If the privileges given to root threads (3% of allowable memory) or a
negative value of /proc/pid/oom_score_adj happen to exceed the amount of
rss of a thread, its badness score overflows as a result of commit
a7f638f9 ("mm, oom: normalize oom scores to oom_score_adj scale only
for userspace").

Fix this by making the type signed and return 1, meaning the thread is
still eligible for kill, if the value is negative.
Reported-by: NDave Jones <davej@redhat.com>
Acked-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>