We have better performances not using DMA for oob operations.
Modify size test so that it is using DMA for size greater than oobsize.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

use_dma was always "1" even if the CPU does not support DMA

Tested on AT91SAM9261EK by Jean-Christophe PLAGNIOL-VILLARD
Reported-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Some SAM9 chips have the ability to perform DMA between CPU and SMC controller.
This patch adds DMA support for SAM9RL, SAM9G45, SSAM9G46,AM9M10, SAM9M11.
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Tested-by: NRyan Mallon <ryan@bluewatersys.com>
Acked-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch fixes

drivers/mtd/nand/atmel_nand.c:372: warning: 'part_probes' defined but not used

which is issued when CONFIG_MTD_PARTITIONS is defined but
CONFIG_MTD_CMDLINE_PARTS not.
Signed-off-by: NAndreas Bießmann <biessmann@corscience.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Return a negative error value instead of a positive
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Unused variable "eccpos" removed from atmel_nand driver.
Signed-off-by: NClaudio Scordino <claudio@evidence.eu.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs.  The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NSneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Just add a new on-flash-bbt module parameter.
Signed-off-by: NSimon Polette <spolette@adetelgroup.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: NAndrew Victor <linux@maxim.org.za>
Acked-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NGregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The functions that write the OOB info (on hardware ECC only) use the 
HW_SYNDROME method.

This is not correct : the start position is "pos = eccsize + chunk" and 
should be eccsize. So, the standard (nand_write_oob_std) function should 
be used. This patch corrects this by using NAND_ECC_HW instead of 
NAND_ECC_HW_SYNDROME.

This has only been tested on small pages nand flash.
(if anyone can test it on large pages that would be great).

kernel version : 2.6.27-rc2 (current git mtd-2.6)
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ALE signal isn't correctly wired up to the ECC controller on the
AP7000, so it starts calculating ECC during the address cycles.

Work around this by resetting the ECC controller between the address and
data cycles.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This uses __raw_{read,write}s{b,w}() primitives to access data on NAND
chips for more efficient I/O.

On an arm926 with memory clocked at 100 MHz, this reduced the elapsed time
for a 64 MiB read by 16%.  ("dd" /dev/mtd0 to /dev/null, with an 8-bit
NAND using hardware ECC and 128KiB blocksize.)

Also some minor section tweaks:

  - Use platform_driver_probe() so no pointer to probe() lingers
    after that code has been removed at run-time.

  - Use __exit and __exit_p so the remove() code will normally be
    removed by the linker.

Since these buffer read/write calls are new, this increases the runtime
code footprint (by 88 bytes on my build, after the section tweaks).

[haavard.skinnemoen@atmel.com: rebase onto atmel_nand rename]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some of them, at least.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This fixes several bugs in the atmel_nand_probe() error path, including
at least one memory leak.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.

Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

No point in using an AT91-specific GPIO API when the generic API works
just as well.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Use at91_nand_enable(), at91_nand_disable() to manipulate enable_pin.
No functional changes.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This driver did not control NCE signal during normal operations (only
enable NCE on probing and disable NCE on removing).  This patch make
NCE signal inactive on idle state.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The sam926x docs allegedly don't list an "ECC_PARITY" field, and the 
header files in the upstream kernel don't have it either.

Masking with it was useless anyway, so just remove it.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).

It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The part_probes[] should be static.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.

NOTE: at91_nand for some reason disallows modular builds.  I'm assuming that's
just an oversight that will be fixed.

[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Call parse_mtd_partitions before checking board's partition_info, so
that "mtdparts=" option can override board's default setting.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: NIvan Kuten <ivan.kuten@promwad.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: NIvan Kuten <ivan.kuten@promwad.com>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch allows you to specify at91_nand partitions on the
kernel command line using the mtdparts variable, if
CONFIG_MTD_CMDLINE_PARTS is set.
Signed-off-by: NFrank Mandarino <fmandarino@endrelia.com>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add support for 16-bit NAND bus-width for the AT91 NAND driver.

The 16-bit NAND is found on the Atmel AT91SAM9260-EK and AT91SAM9261-EK
boards.

Orignal Patch from Patrice Vilchez
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This version only differs from version posted by Savin Zlobec (20 Jun
2006) in that the AT91RM9200-specific chip-select / bus setup code has
been moved from the at91_nand.c driver into the processor-specific file.

From: Savin Zlobec <savin@epico.si>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>