On some IbexPeak systems with ALC889A errors like "azx_get_response
timeout, switching to polling mode: last cmd=0xaf9f000b" are produced,
because non-existent codec #10 is wrongly accessed.

The problem is that snd_hda_get_connections() returns out-of-range result
for NID 0x1c (something like 0xf8f9 or 0xffff).

This patch adds a check to alc880_parse_auto_config() to avoid using
of this out-of-range NIDs. A better fix maybe to improve
snd_hda_get_connections() routine to check for valid NID ranges if
NIDs are expected as result.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Simplify ALC882_TARGA and return gpio3 to ALC883_TARGA_DIG and
ALC883_TARGA_2ch_DIG, which I accidentally removed in commit id
64a8be74Signed-off-by: NDavid Heidelberger <d.okias@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the beep tone calculation for IDT/STAC codecs, lower numbers correspond
to higher frequencies and vice versa.  The current code has this backwards,
resulting in beep frequencies which are way too high (and sound bad on
tinny laptop speakers, resulting in complaints).

[Also added hz <= 0 check by tiwai]
Signed-off-by: NPaul Vojta <vojta@math.berkeley.edu>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There is a regression, introduced in aa202455
(in alsa-kernel) which I noticed when trying to use the headphone socket on
my EeeCPC 901: the output was *very* quiet, practically silent.

This patch corrects the control types to that which was obviously intended in
the referenced commit.
Signed-off-by: NDarren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDA driver disabled HD audio 64bit address support for all AMD
SB600/SB700/SB800 platforms with commit
09240cf4 due to one SB600 issue
reported by community, but we do not see the similar issue on
SB700/SB800 platforms.
This patch is to refine the workaround for SB600 only.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Check the widget type and don't take invalid widgets while parsing
the capture source in patch_via.c.

Also, fixed some compile warnings introduced in the previous commit.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The fixed widget NIDs in patch_via.c seem wrong for some codecs,
and it resulted in the invalid capture source selection.

This patch adds the code to parse the topology instead of using
fixed numbers in order to get the right MUX widget id corresponding
to the ADCs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If the output pin is used and EAPD capability is present, turn on
the EAPD bit.  This fixes the silent output problem on ASUS laptops
with VT1708S codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Minor clean up for initializing the digital-in pin.
No functional changes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Release resources cleanly after errors in the sanity check in
azx_pcm_open().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver.  This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max.  So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing.  If any of them can be zero, disable
the SPDIF sharing mode instead.  Otherwise it will lead to a PCM
configuration error.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The mixer elements created for ASUS eeePC 1000 with ALC269 aren't
standard but strange words like "LineOut".  Rename the element names
to follow the standard one like "Headphone" and "Speaker".
Also, split the volumes to each so that the virtual master can control
them.

The alc269_fujitsu_mixer is removed because it's now identical with
the new eeepc mixer.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HP laptops with AD1984A codecs (at least mobile models) need to set
GPIO1 appropriately to indicate the mute state.  The BIOS checks this
bit to judge whether the mute on or off is sent via F8 key.
Without changing this bit, the BIOS can be confused and may toggle
the mute wrongly.

Reference: Novell bnc#515266
	https://bugzilla.novell.com/show_bug.cgi?id=515266Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added a quirk model=laptop for HP 6930p (103c:30dc) with AD1984A codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

During the changes to clean up / fix the realtek codec initialization
routines in commit 4a79ba34,
I forgot to add the check for ALC268 and ALC269.
This resulted in the missing EAPD and COEF setup for these codecs.

This patch adds the missing checks for these codecs.

Reference: bko#13633
	http://bugzilla.kernel.org/show_bug.cgi?id=13633Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The Line In connector is set up as PIN_IN by default, using
VREF_HIZ. It is connected to both ADCs, so add it to both
input selectors.
Also add the ability to use the input mix (on a SoundBlaster
one would call this "What You Hear").
Signed-off-by: NTony Vroon <tony@linx.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For Acer Aspire 6930G (1025:015e), acre-aspire-6530g model matches
obviously better.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the following bugs of acer-aspire-6530g model with ALC888:
- HP jack to mute all speaker outputs including LFE
- Make digital built-in mic working
Signed-off-by: NEmilio López <buhitoescolar@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Realtek codecs require the pin-sense trigger call before actually
reading the pin-sense.  Without this, the pin-detection might not be
done accurately.

This patch adds the pin-capability check and issues the trigger call
if required.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This reverts commit 9e9f46c4.

Quoting from the commit message:

 "At this point, it seems to solve more problems than it causes, so let's
  try using it by default.  It's an easy revert if it ends up causing
  trouble."

And guess what? The _CRS code causes trouble.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.infradead.org/battery-2.6:
  da9030_battery: Fix race between event handler and monitor
  Add MAX17040 Fuel Gauge driver
  w1: ds2760_battery: add support for sleep mode feature
  w1: ds2760: add support for EEPROM read and write
  ds2760_battery: cleanups in ds2760_battery_probe()

Merge branches 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/{vfs-2.6,audit-current}

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  another race fix in jfs_check_acl()
  Get "no acls for this inode" right, fix shmem breakage
  inline functions left without protection of ifdef (acl)

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  audit: inode watches depend on CONFIG_AUDIT not CONFIG_AUDIT_SYSCALL

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Even though one cannot make use of the audit watch code without
CONFIG_AUDIT_SYSCALL the spaghetti nature of the audit code means that
the audit rule filtering requires that it at least be compiled.

Thus build the audit_watch code when we build auditfilter like it was
before cfcad62c

Clearly this is a point of potential future cleanup..
Reported-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: Fix the write access fault problem for real

commit 64d1304a (futex: setup writeable mapping for futex ops which
modify user space data) did address only half of the problem of write
access faults.

The patch was made on two wrong assumptions:

1) access_ok(VERIFY_WRITE,...) would actually check write access.

   On x86 it does _NOT_. It's a pure address range check.

2) a RW mapped region can not go away under us.

   That's wrong as well. Nobody can prevent another thread to call
   mprotect(PROT_READ) on that region where the futex resides. If that
   call hits between the get_user_pages_fast() verification and the
   actual write access in the atomic region we are toast again.

The solution is to not rely on access_ok and get_user() for any write
access related fault on private and shared futexes. Instead we need to
fault it in with verification of write access.

There is no generic non destructive write mechanism which would fault
the user page in trough a #PF, but as we already know that we will
fault we can as well call get_user_pages() directly and avoid the #PF
overhead.

If get_user_pages() returns -EFAULT we know that we can not fix it
anymore and need to bail out to user space.

Remove a bunch of confusing comments on this issue as well.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org

SLUB uses higher order allocations by default but falls back to small
orders under memory pressure. Make sure the GFP mask used in the initial
allocation doesn't include __GFP_NOFAIL.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Traditionally, we never failed small orders (even regardless of any
__GFP_NOFAIL flags), and slab will allocate order-1 allocations even for
small allocations that could fit in a single page (in order to avoid
excessive fragmentation).

Maybe we should remove this warning entirely, but before making that
judgement, at least limit it to bigger allocations.
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  Staging: octeon-ethernet: Fix race freeing transmit buffers.
  Staging: octeon-ethernet: Convert to use net_device_ops.
  MIPS: Cavium: Add CPU hotplugging code.
  MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
  MIPS: Add arch generic CPU hotplug
  DMA: txx9dmac: use dma_unmap_single if DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE set
  MIPS: Sibyte: Fix build error if CONFIG_SERIAL_SB1250_DUART is undefined.
  MIPS: MIPSsim: Fix build error if MSC01E_INT_BASE is undefined.
  MIPS: Hibernation: Remove SMP TLB and cacheflushing code.
  MIPS: Build fix - include <linux/smp.h> into all smp_processor_id() users.
  MIPS: bug.h Build fix - include <linux/compiler.h>.

The existing code had the following race:

Thread-1                       Thread-2

inc/read in_use
                               inc/read in_use
inc tx_free_list[qos].len
                               inc tx_free_list[qos].len

The actual in_use value was incremented twice, but thread-1 is going
to free memory based on its stale value, and will free one too many
times.  The result is that memory is freed back to the kernel while
its packet is still in the transmit buffer.  If the memory is
overwritten before it is transmitted, the hardware will put a valid
checksum on it and send it out (just like it does with good packets).
If by chance the TCP flags are clobbered but not the addresses or
ports, the result can be a broken TCP stream.

The fix is to track the number of freed packets in a single location
(a Fetch-and-Add Unit register).  That way it can never get out of sync
with itself.

We try to free up to MAX_SKB_TO_FREE (currently 10) buffers at a time.
If fewer are available we adjust the free count with the difference.
The action of claiming buffers to free is atomic so two threads cannot
claim the same buffers.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Convert the driver to use net_device_ops as it is now mandatory.

Also compensate for the removal of struct sk_buff's dst field.

The changes are mostly mechanical, the content of ethernet-common.c
was moved to ethernet.c and ethernet-common.{c,h} are removed.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Thanks to Cavium Inc. for the code contribution and help.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The SMP implementation of suspend and hibernate depends on CPU hotplugging.
In the past we didn't have CPU hotplug so suspend and hibernation were not
possible on SMP systems.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>