This reverts commit d6c9ea90.

We are ripping out commit 35773dac "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12

This reverts commit f2d9b991.

We are ripping out commit 35773dac "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb.  This commit attempted to fix the
issues with that patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org #3.12

xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules.  When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts.  Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.

Commit 35773dac "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this.  It was a quick hack to partially
implement the TD fragment rules.  However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb.  The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.

Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts.  Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts.  This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org # 3.12

Fix a memory leak in the usb_store_new_id() error paths. When bailing out
due to sanity checks, the function left the already allocated usb_dynid
struct in place. This regression was introduced by the following commits:

c63fe8f6 (usb: core: add sanity checks when using bInterfaceClass with new_id)
1b9fb31f (usb: core: check for valid id_table when using the RefId feature)
52a6966c (usb: core: bail out if user gives an unknown RefId when using new_id)

Detected by Coverity: CID 1162604.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding two more IDs to the ftdi_sio usb serial driver.
It now connects Tagsys RFID readers.
There might be more IDs out there for other Tagsys models.
Signed-off-by: NUlrich Hahn <uhahn@eanco.de>
Cc: Johan Hovold <johan@hovold.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This device was mentioned in an OpenWRT forum.  Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
 0: qcdm
 2: nmea
 3: modem
 8: qmi
 9: storage

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

People sometimes create their own custom-configured kernels and forget
to enable CONFIG_SCSI_MULTI_LUN.  This causes problems when they plug
in a USB storage device (such as a card reader) with more than one
LUN.

Fortunately, we can tell fairly easily when a storage device claims to
have more than one LUN.  When that happens, this patch asks the SCSI
layer to probe all the LUNs automatically, regardless of the config
setting.

The patch also updates the Kconfig help text for usb-storage,
explaining that CONFIG_SCSI_MULTI_LUN may be necessary.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NThomas Raschbacher <lordvan@lordvan.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for ANT USB-m Stick from Dynastream Innovations, by listing
USB pid

[34366.944805] usb 6-1: New USB device found, idVendor=0fcf, idProduct=1009
[34366.944817] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[34366.944824] usb 6-1: Product: ANT USB-m Stick
[34366.944831] usb 6-1: Manufacturer: Dynastream Innovations

Device reported (https://code.google.com/p/antpm/issues/detail?id=5) to
work through:
$ modprobe usbserial vendor=0x0fcf product=0x1009
Signed-off-by: NKristóf Ralovich <kristof.ralovich@gmail.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds an unusual-devs entry for the BlackBerry 9000.  This
fixes Bugzilla #22442.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NMoritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Tested-by: NMoritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Cypress ATACB unusual-devs entry for the Super Top SATA bridge
causes problems.  Although it was originally reported only for
bcdDevice = 0x160, its range was much larger.  This resulted in a bug
report for bcdDevice 0x220, so the range was capped at 0x219.  Now
Milan reports errors with bcdDevice 0x150.

Therefore this patch restricts the range to just 0x160.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NMilan Svoboda <milan.svoboda@centrum.cz>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

the PHY layer is supposed to be optional,
considering some PHY have no control bus
for SW to poke around.

After commit 1ae5799e (usb: hcd: Initialize
USB phy if needed) any HCD which didn't provide
a PHY driver would emit annoying error messages.

In this patch we're decreasing those messages
to debugging only and we also add a PHY prefix
or use dev_dbg so we know where they're coming from.
Reported-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.

The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.

Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: NAndre Heider <a.heider@gmail.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit beb7e592 "staging: dwc2: add check on dwc2_core_reset
return" broke the B -> A role switching on OTG-enabled platforms.
This commit fixes it.
Reported-by: NDinh Nguyen <dinguyen@altera.com>
Tested-by: NDinh Nguyen <dinguyen@altera.com>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add usb_disabled() check to prevent kernel oops when booting with "nousb"
in the cmdline:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at bus_add_device+0xe0/0x18c
LR is at device_add_groups+0x1c/0x20
...
[<c02191c0>] (bus_add_device) from [<c0217130>] (device_add+0x41c/0x538)
[<c0217130>] (device_add) from [<c023b1d4>] (usb_new_device+0x270/0x35c)
[<c023b1d4>] (usb_new_device) from [<c0241174>] (usb_add_hcd+0x4fc/0x760)
[<c0241174>] (usb_add_hcd) from [<c0254ce0>] (dwc2_hcd_init+0x434/0x510)
[<c0254ce0>] (dwc2_hcd_init) from [<c02594f4>] (dwc2_driver_probe+0x130/0x170)
[<c02594f4>] (dwc2_driver_probe) from [<c021bbd0>] (platform_drv_probe+0x28/0x58)
Signed-off-by: NAndre Heider <a.heider@gmail.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e8b37332.  Many xHCI
host controllers can only handle 32-bit addresses, and writing 64-bits
at a time causes them to fail.  Reading 64-bits at a time may also cause
them to return 0xffffffff, so revert this commit as well.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This reverts commit 7dd09a1a.

Many xHCI host controllers can only handle 32-bit addresses, and writing
64-bits at a time causes them to fail.  Rafał reports that USB devices
simply do not enumerate, and reverting this patch helps.  Branimir
reports that his host controller doesn't respond to an Enable Slot
command and dies:

[   75.576160] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[   88.991634] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[   88.991748] xhci_hcd 0000:03:00.0: Abort command ring failed
[   88.991845] xhci_hcd 0000:03:00.0: HC died; cleaning up
[   93.985489] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[   93.985494] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[   98.982586] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[   98.982591] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[  103.979696] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[  103.979702] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Reported-by: NRafał Miłecki <zajec5@gmail.com>
Reported-by: NBranimir Maksimovic <branimir.maksimovic@gmail.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>

Commit 9df89d85 "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.

Unfortunately, that's not the case.  The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).

When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:

Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2

lspci for the affected host:

04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
        Subsystem: 1043:1039
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at dd200000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [50] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Capabilities: [80] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <2us, L1 <32us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Kernel driver in use: xhci_hcd
        Kernel modules: xhci_hcd

The commit was backported to stable kernels, and will need to be
reverted there as well.
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Reported-by: NSergey Galanov <sergey.e.galanov@gmail.com>
Cc: stable@vger.kernel.org

Don Zickus <dzickus@redhat.com> writes:

Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail).  This led to frustration as suspend/resume is a common use for
laptops.

Poking around, I applied the reset on resume quirk to this chipset and the
resume started working.  Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDon Zickus <dzickus@redhat.com>
Tested-by: NPrarit Bhargava <prarit@redhat.com>
Cc: stable # 2.6.37

We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".

The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.

We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).

Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.

For stable tree: 3.11+.

Cc: stable <stable@vger.kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: NMatthieu Vanin <b47495@freescale.com>
Tested-by: NMatthieu Vanin <b47495@freescale.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.

For stable tree: 3.12+

Cc: stable@vger.kernel.org
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

hw_phymode_configure configures the PORTSC registers and allow the
following phy_inits to operate on the right parameters. This fix a problem
where the UPLI (ISP1504) could not be detected, because the Viewport was not
available and read the viewport return 0's only.
Signed-off-by: NChris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

* init the sts flag to 0 (missed)
* fix write the real bit not sts value
* Set PORTCS_STS and DEVLC_STS only if sts = 1

[Peter Chen: This one and the next patch fix the problem occurred imx27
and imx31, and imx27 and imx31 usb support are enabled until 3.14, so
these two patches isn't needed for -stable]
Signed-off-by: NChris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.

This patch is needed for stable tree 3.11+

Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Tested-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.

Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2

This patch is needed for stable tree 3.11+.

Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Tested-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.

Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2

Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.

Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Tested-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When implementing the RefId feature, it was missed that id_tables can be
NULL under special circumstances. Bail out in that case.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The DWC2 driver should now be in good enough shape to move out of
staging. I have stress tested it overnight on RPI running mass
storage and Ethernet transfers in parallel, and for several days
on our proprietary PCI-based platform.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Do not decrement resp_count if it's already 0.

We set resp_count to 0 when the device is closed.  The next open and
read will try to clear the WDM_READ flag if there was leftover data
in the read buffer. This fix is necessary to prevent resubmitting
the read URB in a tight loop because resp_count becomes negative.

The bug can easily be triggered from userspace by not reading all
data in the read buffer, and then closing and reopening the chardev.

Fixes: 8dd5cd53 ("usb: cdc-wdm: avoid hanging on zero length reads")
Cc: <stable@vger.kernel.org> # 3.13
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If users use the new RefId feature of new_id, give them an error message
if they provided an unknown reference. That helps detecting typos.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the component
index -- remove the "usb%d_clk" template, always use "ipg" instead

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NGerhard Sittig <gsi@denx.de>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Check if that field is actually used and if so, bail out if it exeeds a
u8. Make it also future-proof by not requiring "exactly three"
parameters in new_id, but simply "more than two".
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fix compilation error when driver is compiled
in multi-platform builds.

drivers/built-in.o: In function `msm_otg_link_clk_reset':
./drivers/usb/phy/phy-msm-usb.c:314: undefined reference to `clk_reset'
./drivers/usb/phy/phy-msm-usb.c:318: undefined reference to `clk_reset'

Use platform data supplied reset handlers and adjust error
messages reported when reset sequence fail.

This is an intermediate step before adding support for reset
framework and newer targets.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NRahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NRahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When we are doing compliance test with xHCI, we found that if we
enable CONFIG_USB_SUSPEND and plug in a bad device which causes
over-current condition to the root port, software will not be noticed.
The reason is that current code don't set hub->change_bits in
hub_activate() when over-current happens, and then hub_events() will
not check the port status because it thinks nothing changed.
If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will
report the change and set hub->event_bits, and then hub_events() will
check what events happened.In this case over-current can be detected.
Signed-off-by: NShen Guang <shenguang10@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 30666249, as it
depended on a previous patch that I rejected, causing a build error
here.  Sorry about that.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 35773dac "usb: xhci: Link TRB
must not occur within a USB payload burst" attempted to fix an issue
found with USB ethernet adapters, and inadvertently broke USB storage
devices.  The patch attempts to ensure that transfers never span a
segment, and rejects transfers that have more than 63 entries (or
possibly less, if some entries cross 64KB boundaries).

usb-storage limits the maximum transfer size to 120K, and we had assumed
the block layer would pass a scatter-gather list of 4K entries,
resulting in no more than 31 sglist entries:

http://marc.info/?l=linux-usb&m=138498190419312&w=2

That assumption was wrong, since we've seen the driver reject a write
that was 218 sectors long (of probably 512 bytes each):

Jan  1 07:04:49 jidanni5 kernel: [  559.624704] xhci_hcd 0000:00:14.0: Too many fragments 79, max 63
...
Jan  1 07:04:58 jidanni5 kernel: [  568.622583] Write(10): 2a 00 00 06 85 0e 00 00 da 00

Limit the number of scatter-gather entries to half a ring segment.  That
should be margin enough in case some entries cross 64KB boundaries.
Increase the number of TRBs per segment from 64 to 256, which should
result in ring segments fitting on a 4K page.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes: 35773dac ('usb: xhci: Link TRB must not occur within a USB payload burst')
Cc: stable <stable@vger.kernel.org> # 3.12