This allows the "make dtbs" to build the aquaris5 dtb for the Mediatek
SoC.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds support for the i.MX1 APF9328 from Armadeus.
This change is intended to further remove non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NRabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add support for the Gateworks GW5520 board.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the Freescale (Motorola) i.MX1 ADS board.
This change is intended to further remove non-DT support for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The Colibri VF61 is a module which needs a carrier board to actually
run. Different carrier board have different hardware support, hence
we should reflect this in the device tree files. This patch adds the
Colibri Evaluation Board, which supports almost all peripherals
defined in the Colibri standard.

Also align the compatible naming, file splitting and file naming with
the scheme which was choosen for the Tegra based modules.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add basic support for the IFC6540 single-board computer boards, that are
based on the APQ8084 SoC. This patch adds the initial device tree and the
neccessary nodes required for enabling the serial port and eMMC.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
[uli: reduced to minimum, added cmt, enabled scif2, split off from SoC]
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

These baseboards are equipped with the Technexion TAO35030 SOM. So
they include this dtsi. The common parts are extracted into an "common"
dtsi file. The main difference between both boards is, that the *lcd
has DSS support enabled for the LCD.

Some HEAD acoustics specific features are:

- LED handling
- Special FPGA/DSP audio driver (not included in this series)
- powerdown GPIO
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This baseboard is equipped with the Technexion TAO35030 SOM. So
includes this dtsi. Some Thunder specific features are:

- LCD panel
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add basic IPQ8064 SoC include device tree and support for basic booting on
the AP148 Reference board with support for UART, I2C, and SPI.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add dts file for Hisilicon x5hd2 development kit board.
Signed-off-by: NHaifeng Yan <yanhaifeng@gmail.com>
Signed-off-by: NJiancheng Xue <jchxue@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NWei Xu <xuwei5@hisilicon.com>
[olof: Rename dts/dtsi to include hisi prefix]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add model a5 which have additional jack detection.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
[tony@atomide.com: fixed a typo for make dtbs to work]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add gta04a3 model with additional acceleromer.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch is preparation of adding more boards which have common moved
to omap3-gta04.dtsi. Other boards have only small additions to omap3-gta04a4.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a sample DTS which will allow bootup of a board populated
with the BCM7445 chip.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>

The Lenovo Iomega ix4-300d is a 4-Bay sata NAS with dual Gb, USB2.0 & 3.0,
powered by a Marvell Armada XP MV78230 dual core CPU.

http://shop.lenovo.com/us/en/servers/network-storage/lenovoemc/ix4-300d/Signed-off-by: NBenoit Masson <yahoo@perenite.com>
Link: https://lkml.kernel.org/r/1406503839-4662-1-git-send-email-yahoo@perenite.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This allows the "make dtbs" target to work.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

This allows to boot the Adapteva Parallella board to serial console.

Cc: Andreas Olofsson <andreas@adapteva.com>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This adds support for the A31 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=172

The Merrii A31 Hummingbird is a development board based on the
Allwinner A31 SoC with multiple USB ports through a USB hub chip,
a uSD slot, a 10/100/1000M ethernet port, an AP6210 WiFi/BT chip,
TV-in, HDMI, VGA, audio in/out ports, and LCD/CSI headers.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: enable usbphy, ehci0, ohci0 for on-board usb hub;
 add pcf8563 rtc node; add comments for i2c0 and mmc0 pull-ups;
 correct ethernet phy address to 0x01; drop uart2 (BT chip has
 no power) and uart3 (no device); use proper commit message]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

Add DTS for s5pc110 boards: goni, aquila, smdkc110
s5pv210: smdkv210, tiny210, torbreck
Signed-off-by: NMateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
[t.figa: Rebased, fixed merge conflicts, neatened.]
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add initial Rex Pro i.mx6dl board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working.  Currently no mainline u-boot, so boot with
cat zImage imx6dl-rex-basic.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working.  Currently no mainline u-boot, so boot with
cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The rev C1 Wandboard uses the Broadcom 4330 for WiFi and Bluetooth instead of
the 4329.  This changes the PADS assigned for the control lines.  Another
side effect of the change is that on the rev C1 board, usdhc driver can't
detect the chip presence correctly so usdhc2 now needs its 'non-removeable'
property removed.

So that rev B1 and earlier can continue to work, this patch splits the
board-specific definitions from imx6qdl-wandboard.dtsi into
imx6qdl-wandboard-revb1.dtsi and imx6qdl-wandboard-revc1.dtsi.  The new files
include the original base imx6qdl-wandboard.dtsi which retains the common
definitions.

The existing imx6dl-wandboard.dts includes imx6qdl-wandboard-revc1.dtsi and
imx6dl-wandboard-revb1.dts (new) includes imx6qdl-wandboard-revb1.dtsi.
This makes the rev C1 board the new default.  The same pattern is used for
imx6q-wandboard.dts.

So, from U-Boot on a WB-Quad you use imxq-wandboard-revb1.dtb for the older B1
board and imxq-wandboard.dtb for the current rev C1 board.
Signed-off-by: NGeorge Joseph <george.joseph@fairview5.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch add support for the imx6dl based aristainetos board
with following configuration:

CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
DRAM:  1 GiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB

As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are five distinct module types with either i.MX6Q or i.MX6DL and
LVDS or LCD display interface and one DTS file for a complete system
with an i.MX6DL based TX6 module and a baseboard mounted on the back
of a display (imx6dl-tx6dl-comtft.dts).
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The CMO-QVGA, DVI-VGA and DVI-SVGA displays were added.
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add initial imx6sx-sdb board support with limited devices enabled.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds the device tree to support Toradex Apalis T30, a
computer on module which can be used on different carrier boards.

The module consists of a Tegra 3 SoC, two PMICs, 1 or 2 GB of DDR3L
RAM, eMMC, an LM95245 temperature sensor chip, an i210 resp. i211
gigabit Ethernet controller, an STMPE811 ADC/touch controller as well
as two MCP2515 CAN controllers. Furthermore, there is an SGTL5000 audio
codec which is not yet supported. Anything that is not self contained
on the module is disabled by default.

The device tree for the Evaluation Board includes the modules device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).

While at it also add the device tree binding documentation for Apalis
T30.
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
[swarren: fixed some node sort orders]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch moves some parts of exynos4412-odroidx.dts to common
exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and
U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz
instead of 1.4GHz), while U2/U3 differs from X2 by different way of
routing signals to host USB hub. It also lacks some hw modules not yet
supported by those dts files (i.e. LCD & touch panel).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Now that all boards have been converted to DT and all the support code
lives in mach-mvebu, we can remove mach-kirkwood.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1405028192-9623-2-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds DT support for the LaCie NAS d2 Network v2 (d2net_v2).
Most of the hardware characteristics are shared with the 2Big and 5Big
Network v2 boards.

- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-3-git-send-email-simon.guinot@sequanux.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].

[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for TI's AM437x StarterKit Evaluation
Module.

Cc: Josh Elliot <jelliott@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFranklin Cooper Jr. <fcooper@ti.com>
Tested-by: NTom Rini <trini@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The ba10 tvbox is an A10 based android tvbox, with 512M RAM, 8G nand flash,
rtl8188ctv usb wifi 1 USB-A receptacle hooked up to an EHCI/OHCI controller,
1 USB-A receptacle hooked up to the OTG and 100Mbit ethernet using a
rtl8201 phy.

The PCB is labelled ba10 hence I've named the board ba10-tvbox. It is used
in noname allwinner A10 tv-boxes.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The LinkSprite pcDuino V3 is an A20 based development board featuring
arduino compatible io headers, 1G RAM, 4G nand, sata, rtl8188cus usb wifi
and 100 Mbit ethernet using an ip101a phy:

http://www.pcduino.com/pcduino-v3/Signed-off-by: NZoltan HERPAI <wigyori@uid0.hu>
[hdegoede@redhat.com: Various cleanups, correct led pins]
[hdegoede@redhat.com: Add axp209, ir and gpio-keys nodes]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets with A23 SoCs. There are at least 2 versions of the board, with
different peripherals, such as WiFi chips.

Common features among these tablets include 512 MB DRAM, NAND, MMC, LCD,
capacitive touchscreen, accelerometer, 1 or 2 camera sensors, USB OTG,
microphone and speaker.

v5 of these board designs has a ESP8089 WiFi chip (not supported)
connected to mmc1. This patch adds very basic support.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

As Mainlining effort for SolidRun CuBox has been carried out on the
Engineering Sample, the board DTS was reflecting this. Actually,
SolidRun CuBox comes in three different variants:
Engineering Sample (ES), production with 1GB RAM (1G),
and production with 2GB RAM (2G).

Therefore, we base current dove-cubox.dts on to the 1G production
variant and add a ES dts to add required quirk for misrouted SDHCI
card detect on top of dove-cubox.dts. For the 2G variant we rely on
the bootloader to setup correct RAM size.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1401228006-3212-1-git-send-email-sebastian.hesselbarth@gmail.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Describe LaCie 2Big and 5Big Network v2 using device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1401132591-26305-3-git-send-email-andrew@lunn.chAcked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>