Device tree binding documentation for the TS-4800
GPIO controller.
Signed-off-by: NJulien Grossholtz <julien.grossholtz@savoirfairelinux.com>
[Point ngpios to gpio.txt]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Use irq_data_get_chip_type() instead of container_of().
Signed-off-by: NGeliang Tang <geliangtang@163.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: NLiu Gang <Gang.Liu@nxp.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add F81866 GPIO supports

Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.

Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html

The control method is the same with F7188x, but we should care the address
of GPIO8x.

GPIO address is below:
    GPIO0x based: 0xf0
    GPIO1x based: 0xe0
    GPIO2x based: 0xd0
    GPIO3x based: 0xc0
    GPIO4x based: 0xb0
    GPIO5x based: 0xa0
    GPIO6x based: 0x90
    GPIO7x based: 0x80
    GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.

This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.

This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ACCES 104-IDI-48 can differentiate between its own and other
devices' interrupt requests. Therefore, IRQ sharing is possible and
should be permitted.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.

  The executive summary:

   - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
   - Avoid useless rebuilds for zboot.
   - jz4780: Add NEMC, BCH and NAND device tree nodes
   - Initial support for the MicroChip's DT platform.  As all the device
     drivers are missing this is still of limited use.
   - Some Loongson3 cleanups.
   - The unavoidable whitespace polishing.
   - Reduce clock skew when synchronizing the CPU cycle counters on CPU
     startup.
   - Add MIPS R6 fixes.
   - Lots of cleanups across arch/mips as fallout from KVM.
   - Lots of minor fixes and changes for IEEE 754-2008 support to the
     FPU emulator / fp-assist software.
   - Minor Ralink, BCM47xx and bcm963xx platform support improvments.
   - Support SMP on BCM63168"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  MIPS: Update trap codes
  MIPS: Move Cause.ExcCode trap codes to mipsregs.h
  MIPS: KVM: Make kvm_mips_{init,exit}() static
  MIPS: KVM: Refactor added offsetof()s
  MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
  ...

Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "Emergency travel prevented me from completing my final testing on this
  until today.  Nothing here that couldn't wait until RC1 fixes, but I
  thought it best to get it out sooner rather than later as it does
  contain a build warning fix.

  Summary:

  A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:

  ideapad-laptop:
   - Add Lenovo Yoga 700 to no_hw_rfkill dmi list

  MAINTAINERS:
   - Combine multiple telemetry entries

  intel_telemetry_debugfs:
   - Fix unused warnings in telemetry debugfs"

* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs

Pull thermal management updates from Zhang Rui:
 "The top merge commit was re-generated yesterday because two topic
  branches were dropped from this pull request in the last minute due to
  some unaddressed comments.  All the other material has been in
  linux-next for quite a while.

  Specifics:

   - Enhance thermal core to handle unexpected device cooling states
     after fresh boot and system resume.  From Zhang Rui and Chen Yu.

   - Several fixes and cleanups on Rockchip and RCAR thermal drivers.
     From Caesar Wang and Kuninori Morimoto.

   - Add Broxton support for Intel processor thermal reporting device
     driver.  From Amy Wiles"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: trip_point_temp_store() calls thermal_zone_device_update()
  thermal: rcar: rcar_thermal_get_temp() return error if strange temp
  thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
  thermal: rcar: check every rcar_thermal_update_temp() return value
  thermal: rcar: move rcar_thermal_dt_ids to upside
  thermal: rockchip: Support the RK3399 SoCs in thermal driver
  thermal: rockchip: Support the RK3228 SoCs in thermal driver
  dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
  thermal: rockchip: fix a trivial typo
  Thermal: Enable Broxton SoC thermal reporting device
  thermal: constify pch_dev_ops structure
  Thermal: do thermal zone update after a cooling device registered
  Thermal: handle thermal zone device properly during system sleep
  Thermal: initialize thermal zone device correctly

Pull 9p updates from Eric Van Hensbergen:
 "Sorry for the last minute pull request, there's was a change that
  didn't get pulled into for-next until two weeks ago and I wanted to
  give it some bake time.

  Summary:

  Rework and error handling fixes, primarily in the fscatch and fd
  transports"

* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: use fscache mutex rather than spinlock
  9p: trans_fd, bail out if recv fcall if missing
  9p: trans_fd, read rework to use p9_parse_header
  net/9p: Add device name details on error

Pull Ceph updates from Sage Weil:
 "The two main changes are aio support in CephFS, and a series that
  fixes several issues in the authentication key timeout/renewal code.

  On top of that are a variety of cleanups and minor bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: remove outdated comment
  libceph: kill off ceph_x_ticket_handler::validity
  libceph: invalidate AUTH in addition to a service ticket
  libceph: fix authorizer invalidation, take 2
  libceph: clear messenger auth_retry flag if we fault
  libceph: fix ceph_msg_revoke()
  libceph: use list_for_each_entry_safe
  ceph: use i_size_{read,write} to get/set i_size
  ceph: re-send AIO write request when getting -EOLDSNAP error
  ceph: Asynchronous IO support
  ceph: Avoid to propagate the invalid page point
  ceph: fix double page_unlock() in page_mkwrite()
  rbd: delete an unnecessary check before rbd_dev_destroy()
  libceph: use list_next_entry instead of list_entry_next
  ceph: ceph_frag_contains_value can be boolean
  ceph: remove unused functions in ceph_frag.h

Pull SMB3 fixes from Steve French:
 "A collection of CIFS/SMB3 fixes.

  It includes a couple bug fixes, a few for improved debugging of
  cifs.ko and some improvements to the way cifs does key generation.

  I do have some additional bug fixes I expect in the next week or two
  (to address a problem found by xfstest, and some fixes for SMB3.11
  dialect, and a couple patches that just came in yesterday that I am
  reviewing)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
  cifs: fix race between call_async() and reconnect()
  Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
  cifs: Allow using O_DIRECT with cache=loose
  cifs: Make echo interval tunable
  cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
  Print IP address of unresponsive server
  cifs: Ratelimit kernel log messages

Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.

This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272
Tested-by: <dinyar.rabady+spam@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

This patch combines all the telemetry file entries in MAINTAINERS via
wildcard.
Signed-off-by: NSouvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

This patch fixes compile time warnings when CONFIG_PM_SLEEP
is undefined. In this case sleep related counters are unused.
Signed-off-by: NSouvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

If we detect that there is nothing to do just set the flag and do not
check if it was already set before.  Races really do not matter.  If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.

Since commit 0eb77e98 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd.  This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up.  The VM_BUG_ON is therefore misleading and no more
appropriate.  Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly.  Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NChristoph Lameter <cl@linux.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.

When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Allow BMIPS_GENERIC supported platforms to build GPIO controller
drivers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NDragan Stancevic <dragan.stancevic@gmail.com>
Cc: cernekee@gmail.com
Cc: jaedon.shin@gmail.com
Cc: gregory.0xf0@gmail.com
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12019/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The "dual_image" and "inactive_flag" fields should be merged into a single
"image_sequence" field.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11834/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.

Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.

Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Broadcom BCM963xx boards have multiple nvram variants across different
SoCs with additional checksum fields added whenever the size of the
nvram was extended.

Add this structure as a header file so that multiple drivers can use it.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11830/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Pull rdma updates from Doug Ledford:
 "Initial roundup of 4.5 merge window patches

   - Remove usage of ib_query_device and instead store attributes in
     ib_device struct

   - Move iopoll out of block and into lib, rename to irqpoll, and use
     in several places in the rdma stack as our new completion queue
     polling library mechanism.  Update the other block drivers that
     already used iopoll to use the new mechanism too.

   - Replace the per-entry GID table locks with a single GID table lock

   - IPoIB multicast cleanup

   - Cleanups to the IB MR facility

   - Add support for 64bit extended IB counters

   - Fix for netlink oops while parsing RDMA nl messages

   - RoCEv2 support for the core IB code

   - mlx4 RoCEv2 support

   - mlx5 RoCEv2 support

   - Cross Channel support for mlx5

   - Timestamp support for mlx5

   - Atomic support for mlx5

   - Raw QP support for mlx5

   - MAINTAINERS update for mlx4/mlx5

   - Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates

   - Add support for remote invalidate to the iSER driver (pushed
     through the RDMA tree due to dependencies, acknowledged by nab)

   - Update to NFSoRDMA (pushed through the RDMA tree due to
     dependencies, acknowledged by Bruce)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
  IB/mlx5: Unify CQ create flags check
  IB/mlx5: Expose Raw Packet QP to user space consumers
  {IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
  IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
  IB/mlx5: Add Raw Packet QP query functionality
  IB/mlx5: Add create and destroy functionality for Raw Packet QP
  IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
  IB/mlx5: Allocate a Transport Domain for each ucontext
  net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
  net/mlx5_core: Add RQ and SQ event handling
  net/mlx5_core: Export transport objects
  IB/mlx5: Expose CQE version to user-space
  IB/mlx5: Add CQE version 1 support to user QPs and SRQs
  IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
  IB/sa: Fix netlink local service GFP crash
  IB/srpt: Remove redundant wc array
  IB/qib: Improve ipoib UD performance
  IB/mlx4: Advertise RoCE v2 support
  IB/mlx4: Create and use another QP1 for RoCEv2
  IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
  ...

I've pretty much been maintaining KVM for MIPS for a while now. Lets
make it more official (and make sure I get Cc'd on relevant patches).
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11898/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add missing newline to end of kvm_err string when guest PMAP couldn't be
allocated.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11896/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.

Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11895/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11893/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.

To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11892/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The first argument to set_except_vector is the ExcCode, which we now
have definitions for. Lets make use of them.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11894/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a few missing trap codes.

[ralf@linux-mips.org: Drop removal of exception codes.  I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11890/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11891/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The module init and exit functions have no need to be global, so make
them static.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11889/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When calculating the offsets into the commpage for dynamically
translated mtc0/mfc0 guest instructions, multiple offsetof()s are added
together to find the offset of the specific register in the mips_coproc,
within the commpage.

Simplify each of these cases to a single offsetof() to find the offset
of the specific register within the commpage.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11888/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Export symbols only to GPL modules to match other KVM symbols in
virt/kvm/ and arch/*/kvm/.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11887/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>