Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.

If the IWCM returns an error, then we must abort the connection and
release resources.  Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

These are generated by HW in some error cases and need to be
silently discarded.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

If cxgb4_ofld_send() returns < 0, then send_fw_pass_open_req() must
free the request skb and the saved skb with the tcp header.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

We cannot save the mapped length using the rdma max_page_list_len field
of the ib_fast_reg_page_list struct because the core code uses it.  This
results in an incorrect unmap of the page list in c4iw_free_fastreg_pbl().

I found this with dma mapping debugging enabled in the kernel.  The
fix is to save the length in the c4iw_fr_page_list struct.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Based on original work from Jay Hernandez <jay@chelsio.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Always release the neigh entry in rx_pkt().

Based on original work by Santosh Rastapur <santosh@chelsio.com>.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

find_route() must treat loopback as a valid egress interface.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

There is a four byte hole at the end of the "uresp" struct after the
->qid_mask member.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

These sizes should be unsigned so we don't allow negative values and
have underflow bugs.  These can come from the user so there may be
security implications, but I have not tested this.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

We should use rdma_vlan_dev_real_dev() instead of using vlan_dev_real_dev()
when building the GID table for a vlan interface.
Signed-off-by: NDevesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Use correct value for obtaining traffic class from device
response for Query QP request.
Signed-off-by: NDevesh Sharma <devesh.sharma@emulex.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Error reported at http://marc.info/?l=linux-rdma&m=138995755801039&w=2

Fix short to int cast for big endian systems.
Signed-off-by: NUpinder Malhi <umalhi@cisco.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Research has shown that commit a77fcf89 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.

This patch add that sequence.

Cc: <stable@vger.kernel.org>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly.  For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The IBoE code used to reset the GID table did it for all Ethernet
ports of the device.  Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table.  Change the reset flow to be
per-port.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Updating the GID table under IBoE requires read/write from/to shared
data structures.  These data structures are protected with the device
iboe lock.  The flows that modify the GID table start from

    1. Initializing the GID table
    2. NETDEV events
    3. INET or INET6 events

This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held.  On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.

This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.

Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned.  This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

When the device has only Ethernet ports, don't try to allocate range
of steerable UD QPs since they aren't needed.  This fixes an issue
where mlx4 VFs tried to allocate a range of UD steerable QPs, but
failed to do so.

Fixes: c1c98501 ("IB/mlx4: Add support for steerable IB UD QPs")
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Set the return variable to an error code as done elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Set the return variable to an error code as done elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Currently Connect-IB does not support blocking multicast loopback, so
don't set IB_DEVICE_BLOCK_MULTICAST_LOOPBACK in the device caps.

Reported by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Commit c1be5232 ("Fix micro UAR allocator") broke binary compatibility
between libmlx5 and mlx5_ib since it defines a different value to the number
of micro UARs per page, leading to wrong calculation in libmlx5. This patch
defines struct mlx5_ib_alloc_ucontext_req_v2 as an extension to struct
mlx5_ib_alloc_ucontext_req.  The extended size is determined in mlx5_ib_alloc_ucontext()
and in case of old library we use uuarn 0 which works fine -- this is
acheived due to create_user_qp() falling back from high to medium then to
low class where low class will return 0.  For new libraries we use the
more sophisticated allocation algorithm.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NYann Droneaud <ydroneaud@opteya.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: NYann Droneaud <ydroneaud@opteya.com>
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The current code attmepts to call ib_umem_get() even if the length is
zero, which causes a failure. Since the spec allows zero length work
queues, change the code so we don't call ib_umem_get() in those cases.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Modify CQ is used by ULPs like IPoIB to change moderation parameters.  This
patch adds support in mlx5.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Put a wmb() to make sure the doorbell record is visible to the HCA before we
hit doorbell.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Use the possibly more efficient ether_addr_equal() instead of memcmp().
Signed-off-by: NWang Weidong <wangweidong1@huawei.com>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The GSI QP type is compatible with and should be allowed to send data
to/from any UD QP.  This was found when testing ibacm on the same node
as an SA.

Cc: <stable@vger.kernel.org>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Building mem.o for 32 bits x86 triggers a GCC warning:

    drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
    drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64.  That's what _c4iw_write_mem_inline() already does.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>