The driver sometimes needs to know which function number the current
device is.  This patch changes the code to use devfn over internal
register values.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 serdes phy brings link up via parallel detection without any
additional help from the driver.  This patch changes the
tg3_setup_fiber_mii_phy() function to detect and allow the use of this
feature.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the code to make it legal to allocate only one MSI-X
vector.  It also fixes a bug where the driver was not checking for error
return codes from pci_enable_msix().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was incorrectly programming the indirection table such that
rx traffic intended for the second ring went to the first ring, rx
traffic intended for the third ring went to the second ring, etc.  This
patch changes the code so that rx traffic is diverted to the proper
ring.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rx resources for MSI-X interrupt vector 0 were not being freed
correctly.  This happens because the teardown loop continue's to the
next loop iteration if it detects the tx ring for that vector is not
setup, thus bypassing the rx teardown code.  This patch moves the
call to tg3_rx_prodring_free() earlier in the loop.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain edge conditions, internal tx resources can get corrupted.
This patch enables a bit that will fix the problem.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 and later devices relocate the APE mutex registers.  This patch
organizes the code so that the driver can use the mutex registers in the
old and new locations.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some configurations need delay between the "write completed" indication
and new write to work reliably.

Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.

This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856 (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Acked-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable GRO by default for performance.
Signed-off-by: NShirley Ma <xma@us.ibm.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch compile tested only.

Convert legacy PM hooks to dev_pm_ops
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2: changed bonding module version, modified to apply on top of changes
from previous patch in series, and updated documentation to elaborate on
multiqueue awareness that now exists in bonding driver.

This patch give the user the ability to control the output slave for
round-robin and active-backup bonding.  Similar functionality was
discussed in the past, but Jay Vosburgh indicated he would rather see a
feature like this added to existing modes rather than creating a
completely new mode.  Jay's thoughts as well as Neil's input surrounding
some of the issues with the first implementation pushed us toward a
design that relied on the queue_mapping rather than skb marks.
Round-robin and active-backup modes were chosen as the first users of
this slave selection as they seemed like the most logical choices when
considering a multi-switch environment.

Round-robin mode works without any modification, but active-backup does
require inclusion of the first patch in this series and setting
the 'all_slaves_active' flag.  This will allow reception of unicast traffic on
any of the backup interfaces.

This was tested with IPv4-based filters as well as VLAN-based filters
with good results.

More information as well as a configuration example is available in the
patch to Documentation/networking/bonding.txt.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

v2: changed parameter name from 'keep_all' to 'all_slaves_active' and
skipped setting slaves to inactive rather than creating a new flag at
Jay's suggestion.

In an effort to suppress duplicate frames on certain bonding modes
(specifically the modes that do not require additional configuration on
the switch or switches connected to the host), code was added in the
generic receive patch in 2.6.16.  The current behavior works quite well
for most users, but there are some times it would be nice to restore old
functionality and allow all frames to make their way up the stack.

This patch adds support for a new module option and sysfs file called
'all_slaves_active' that will restore pre-2.6.16 functionality if the
user desires.  The default value is '0' and retains existing behavior,
but the user can set it to '1' and allow all frames up if desired.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hi,
 __pppoe_xmit() in drivers/net/pppoe always returns 1.
When the methods fails (via goto abort), it should return 0 and not 1.

Regards,
Rami Rosen
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated #include('s) in drivers/net/wan/x25_asy.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bug in multilink fragment size calculation introduced by
commit 9c705260
"ppp: ppp_mp_explode() redesign"
Signed-off-by: NBen McKeegan <ben@netservers.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only check pfc bits in hang logic if PFC is enabled.  Previously,
if DCB was enabled but PFC was disabled the incorrect pause
bits would be checked.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Original code was placed incorrectly inside a block of code marked
with CONFIG_INET directive. Fix by moving it outside.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Tested-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is alternative to a previous patch submitted by Joe Perches.

Create common macros e_<level> and e_dev_<level> that use netdev_<level> and
dev_<level> similar to e1000e.
Redefined pr_fmt for driver messages.
Use %pM to display MAC address.
Aligned text to better match the new format.

CC: Joe Perches <joe@perches.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.

CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This exposes the port number to userland through sysfs.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Probably no one has used this driver on big-endian systems, since it was
setting up descriptor swapping if CONFIG_BIG_ENDIAN is set, which it
never is, since that symbol is not mentioned anywhere else in the kernel
source.  Switch this test to a check for __BIG_ENDIAN so it has a chance
at working.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bitwise negate is intended here.  With the logical negate the
condition is always false.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021.  Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region.  Currently we use the PCI function number, but the
PCI address may be virtualised.  Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cleanup patch.

Use new __packed annotation in drivers/net/
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup PHY probing: use helpers from phylib
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert TX hook return value to netdev_tx_t
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 5c7fffd0 ("drivers/net/mac8390.c: Remove
useless memcpy casting") removed too many casts, introducing the following
warnings:

| drivers/net/mac8390.c:248: warning: passing argument 1 of '__builtin_memcpy' makes pointer from integer without a cast
| drivers/net/mac8390.c:253: warning: passing argument 1 of 'word_memcpy_tocard' makes pointer from integer without a cast
| drivers/net/mac8390.c:255: warning: passing argument 2 of 'word_memcpy_fromcard' makes pointer from integer without a cast

Instead of just readding the casts,
  - move all casts inside word_memcpy_{to,from}card(),
  - replace an incorrect memcpy() by memcpy_toio(),
  - add memcmp_withio() as a wrapper around memcmp(),
  - replace an incorrect memcpy_toio() by memcpy_fromio().
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Tested-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_CHELSIO_T1_COUGAR cannot be set (it appears nowhere in any
Kconfig files), and the code it protects could never build (cspi.h was
never added to the kernel tree).  Therefore it's pretty safe to remove
all vestiges of this dead code.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

What this patch does is it removes two receive frame hooks (for bridge and for
macvlan) from __netif_receive_skb. These are replaced them with a single
hook for both. It only supports one hook per device because it makes no
sense to do bridging and macvlan on the same device.

Then a network driver (of virtual netdev like macvlan or bridge) can register
an rx_handler for needed net device.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log error conditions using KERN_ERR priority.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This way, RX DMA overruns (actually being caused by overrun of the
512byte input FIFO) show up in ifconfig output. The rx_fifo_errors
counter is unused otherwise.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch completes commit 89d71a66
which missed this spot, as it seems.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By calling korina_restart(), the IRQ handler tries to disable the
interrupt it's currently serving. This leads to a deadlock since
disable_irq() waits for any running IRQ handlers to finish before
returning. This patch addresses the issue by turning korina_restart()
into a workqueue task, which is then scheduled when needed.

Reproducing the deadlock is easily done using e.g. GNU netcat to send
large amounts of UDP data to the host running this driver.

Note that the same problem (and fix) applies to TX FIFO underruns, but
apparently these are less easy to trigger.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Linux 2.6.33 reports this checkstack warning:

drivers/net/vxge/vxge-main.c: In function 'vxge_probe':
drivers/net/vxge/vxge-main.c:4409: warning: the frame size of 1028 bytes is larger than 1024 bytes

This warning does not occur in the latest linux-2.6 or linux-next, however,
when I do a 'make -j32 CONFIG_FRAME_WARN=512' instead of 1024 I see

drivers/net/vxge/vxge-main.c: In function ‘vxge_probe’:
drivers/net/vxge/vxge-main.c:4423: warning: the frame size of 1024 bytes is larger than 512 bytes

This patch moves the large vxge_config struct off the stack.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sparse complains about shadowed declaration of skb. So use other
name.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the request_irq() error code as the return value for mac8390_open().
EAGAIN doesn't make sense for Nubus slot IRQs. Only this driver can claim
this IRQ (until the NIC is removed, which means everything is powered
down).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I added newlines after the declarations in caif_serial.c.  This is
normal kernel style, although I can't see anywhere it's documented.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't use the "ser" variable so I've removed it.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>