- 02 9月, 2010 5 次提交
-
-
由 Denis Kirjanov 提交于
mdiobus resources must be released on exit Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org> Acked-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jeff Mahoney 提交于
While reviewing commit 1c40be12, I audited other users of tc_action_ops->dump for information leaks. That commit covered almost all of them but act_police still had a leak. opt.limit and opt.capab aren't zeroed out before the structure is passed out. This patch uses the C99 initializers to zero everything unused out. Signed-off-by: NJeff Mahoney <jeffm@suse.com> Acked-by: NJeff Mahoney <jeffm@suse.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Its currently illegal to call kthread_stop(NULL) Reported-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Breno Leitao 提交于
This change just add the IBM eHEA 10Gb network drivers as supported. Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 9月, 2010 4 次提交
-
-
由 Luis R. Rodriguez 提交于
The 5 GHz CTL indexes were not being read for all hardware devices due to the masking out through the CTL_MODE_M mask being one bit too short. Without this the calibrated regulatory maximum values were not being picked up when devices operate on 5 GHz in HT40 mode. The final output power used for Atheros devices is the minimum between the calibrated CTL values and what CRDA provides. Cc: stable@kernel.org [2.6.27+] Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
The EEPROM is compressed on AR9003, upon decompression the wrong upper limit was being used for the block which prevented the 5 GHz CTL indexes from being used, which are stored towards the end of the EEPROM block. This fix allows the actual intended regulatory limits to be used on AR9003 hardware. Cc: stable@kernel.org [2.6.36+] Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Otherwise lockdep complains... https://bugzilla.kernel.org/show_bug.cgi?id=17311 [ INFO: possible circular locking dependency detected ] 2.6.36-rc2-git4 #12 ------------------------------------------------------- kworker/0:3/3630 is trying to acquire lock: (rtnl_mutex){+.+.+.}, at: [<ffffffff813396c7>] rtnl_lock+0x12/0x14 but task is already holding lock: (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa014b129>] rfkill_switch_all+0x24/0x49 [rfkill] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (rfkill_global_mutex){+.+.+.}: [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffffa014b4ab>] rfkill_register+0x2b/0x29c [rfkill] [<ffffffffa0185ba0>] wiphy_register+0x1ae/0x270 [cfg80211] [<ffffffffa0206f01>] ieee80211_register_hw+0x1b4/0x3cf [mac80211] [<ffffffffa0292e98>] iwl_ucode_callback+0x9e9/0xae3 [iwlagn] [<ffffffff812d3e9d>] request_firmware_work_func+0x54/0x6f [<ffffffff81065d15>] kthread+0x8c/0x94 [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10 -> #1 (cfg80211_mutex){+.+.+.}: [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffffa018605e>] cfg80211_get_dev_from_ifindex+0x1b/0x7c [cfg80211] [<ffffffffa0189f36>] cfg80211_wext_giwscan+0x58/0x990 [cfg80211] [<ffffffff8139a3ce>] ioctl_standard_iw_point+0x1a8/0x272 [<ffffffff8139a529>] ioctl_standard_call+0x91/0xa7 [<ffffffff8139a687>] T.723+0xbd/0x12c [<ffffffff8139a727>] wext_handle_ioctl+0x31/0x6d [<ffffffff8133014e>] dev_ioctl+0x63d/0x67a [<ffffffff8131afd9>] sock_ioctl+0x48/0x21d [<ffffffff81102abd>] do_vfs_ioctl+0x4ba/0x509 [<ffffffff81102b5d>] sys_ioctl+0x51/0x74 [<ffffffff81009e02>] system_call_fastpath+0x16/0x1b -> #0 (rtnl_mutex){+.+.+.}: [<ffffffff810796b0>] __lock_acquire+0xa93/0xd9a [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffff813396c7>] rtnl_lock+0x12/0x14 [<ffffffffa0185cb5>] cfg80211_rfkill_set_block+0x1a/0x7b [cfg80211] [<ffffffffa014aed0>] rfkill_set_block+0x80/0xd5 [rfkill] [<ffffffffa014b07e>] __rfkill_switch_all+0x3f/0x6f [rfkill] [<ffffffffa014b13d>] rfkill_switch_all+0x38/0x49 [rfkill] [<ffffffffa014b821>] rfkill_op_handler+0x105/0x136 [rfkill] [<ffffffff81060708>] process_one_work+0x248/0x403 [<ffffffff81062620>] worker_thread+0x139/0x214 [<ffffffff81065d15>] kthread+0x8c/0x94 [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10 Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net>
-
由 David S. Miller 提交于
Once we started enforcing the a nl_table[] entry exist for a protocol, NETLINK_USERSOCK stopped working. Add a dummy table entry so that it works again. Reported-by: NThomas Voegtle <tv@lio96.de> Tested-by: NThomas Voegtle <tv@lio96.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 8月, 2010 6 次提交
-
-
由 David S. Miller 提交于
If irda_open_tsap() fails, the irda_bind() code tries to destroy the ->ias_obj object by hand, but does so wrongly. In particular, it fails to a) release the hashbin attached to the object and b) reset the self->ias_obj pointer to NULL. Fix both problems by using irias_delete_object() and explicitly setting self->ias_obj to NULL, just as irda_release() does. Reported-by: NTavis Ormandy <taviso@cmpxchg8b.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Johannes Berg 提交于
Wireless extensions have an unfortunate, undocumented requirement which requires drivers to always fill iwp->length when returning a successful status. When a driver doesn't do this, it leads to a kernel heap content leak when userspace offers a larger buffer than would have been necessary. Arguably, this is a driver bug, as it should, if it returns 0, fill iwp->length, even if it separately indicated that the buffer contents was not valid. However, we can also at least avoid the memory content leak if the driver doesn't do this by setting the iwp length to max_tokens, which then reflects how big the buffer is that the driver may fill, regardless of how big the userspace buffer is. To illustrate the point, this patch also fixes a corresponding cfg80211 bug (since this requirement isn't documented nor was ever pointed out by anyone during code review, I don't trust all drivers nor all cfg80211 handlers to implement it correctly). Cc: stable@kernel.org [all the way back] Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Reported-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The new workqueue changes helped me find this bug that's been lingering since the changes to the work processing in mac80211 -- the work timer is never deleted properly. Do that to avoid having it fire after all data structures have been freed. It can't be re-armed because all it will do, if running, is schedule the work, but that gets flushed later and won't have anything to do since all work items are gone by now (by way of interface removal). Cc: stable@kernel.org [2.6.34+] Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
Michael reported that p54* never really entered power save mode, even tough it was enabled. It turned out that upon a power save mode change the firmware will set a special flag onto the last outgoing frame tx status (which in this case is almost always the designated PSM nullfunc frame). This flag confused the driver; It erroneously reported transmission failures to the stack, which then generated the next nullfunc. and so on... Cc: <stable@kernel.org> Reported-by: NMichael Buesch <mb@bu3sch.de> Tested-by: NMichael Buesch <mb@bu3sch.de> Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
This avoids a NULL pointer dereference as reported here: https://bugzilla.redhat.com/show_bug.cgi?id=625889 When the WARN condition is hit in ieee80211_get_tx_rate, it will return NULL. So, we need to check the return value and avoid dereferencing it in that case. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Cc: stable@kernel.org Acked-by: NBob Copeland <me@bobcopeland.com>
-
- 29 8月, 2010 1 次提交
-
-
由 Ken Kawasaki 提交于
pcnet_cs: add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card. Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 8月, 2010 2 次提交
-
-
由 Julia Lawall 提交于
The string clone is only used as a temporary copy of the argument val within the while loop, and so it should be freed before leaving the function. The call to strsep, however, modifies clone, so a pointer to the front of the string is kept in saved_clone, to make it possible to free it. The sematic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r exists@ local idexpression x; expression E; identifier l; statement S; @@ *x= \(kasprintf\|kstrdup\)(...); ... if (x == NULL) S ... when != kfree(x) when != E = x if (...) { <... when != kfree(x) * goto l; ...> * return ...; } // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Mike Rapoport 提交于
The commit 886275ce (param: lock if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes) introduced new fields into the if_sdio_card structure. It caused missalignment of the if_sdio_card.buffer field and failure at driver load time: ~# modprobe libertas_sdio [ 62.315124] libertas_sdio: Libertas SDIO driver [ 62.319976] libertas_sdio: Copyright Pierre Ossman [ 63.020629] DMA misaligned error with device 48 [ 63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800 [ 66.005035] libertas: command 0x0003 timed out [ 66.009826] libertas: Timeout submitting command 0x0003 [ 66.016296] libertas: PREP_CMD: command 0x0003 failed: -110 Adding explicit alignment attribute for the if_sdio_card.buffer field fixes this problem. Signed-off-by: NMike Rapoport <mike@compulab.co.il> Acked-by: NMarek Vasut <marek.vasut@gmail.com> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 27 8月, 2010 4 次提交
-
-
由 Jeff Mahoney 提交于
caif does not build on ia64 starting with 2.6.32-rc1. Using asm/unaligned.h instead of linux/unaligned/le_byteshift.h fixes the issue. include/linux/unaligned/le_byteshift.h:40:50: error: redefinition of 'get_unaligned_le16' include/linux/unaligned/le_byteshift.h:45:50: error: redefinition of 'get_unaligned_le32' include/linux/unaligned/le_byteshift.h:50:50: error: redefinition of 'get_unaligned_le64' include/linux/unaligned/le_byteshift.h:55:51: error: redefinition of 'put_unaligned_le16' include/linux/unaligned/le_byteshift.h:60:51: error: redefinition of 'put_unaligned_le32' include/linux/unaligned/le_byteshift.h:65:51: error: redefinition of 'put_unaligned_le64' include/linux/unaligned/le_struct.h:31:51: note: previous definition of 'put_unaligned_le64' was here Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bernard Pidoux F6BVP 提交于
This patch moves a missplaced sock_put(sk) after bh_unlock_sock(sk) like in other parts of AX25 driver. Signed-off-by: NBernard Pidoux <f6bvp@free.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Breno Leitao 提交于
Qlge is freeing the buffers before stopping the card DMA, and this can cause some severe error, as a EEH event on PPC. This patch just stop the card and then free the resources. Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: NRon Mercer <ron.mercer@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
close https://bugzilla.kernel.org/show_bug.cgi?id=16529 Before calling dev_forward_skb(), we should make sure skb head contains at least an ethernet header, even if length included in upper layer said so. Use pskb_may_pull() to make sure this ethernet header is present in skb head. Reported-by: NThomas Heil <heil@terminal-consulting.de> Reported-by: NIan Campbell <Ian.Campbell@eu.citrix.com> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 8月, 2010 2 次提交
-
-
由 KOSAKI Motohiro 提交于
This issue come from ruby language community. Below test program hang up when only run on Linux. % uname -mrsv Linux 2.6.26-2-486 #1 Sat Dec 26 08:37:39 UTC 2009 i686 % ruby -rsocket -ve ' BasicSocket.do_not_reverse_lookup = true serv = TCPServer.open("127.0.0.1", 0) s1 = TCPSocket.open("127.0.0.1", serv.addr[1]) s2 = serv.accept s2.close s1.write("a") rescue p $! s1.write("a") rescue p $! Thread.new { s1.write("a") }.join' ruby 1.9.3dev (2010-07-06 trunk 28554) [i686-linux] #<Errno::EPIPE: Broken pipe> [Hang Here] FreeBSD, Solaris, Mac doesn't. because Ruby's write() method call select() internally. and tcp_poll has a bug. SUS defined 'ready for writing' of select() as following. | A descriptor shall be considered ready for writing when a call to an output | function with O_NONBLOCK clear would not block, whether or not the function | would transfer data successfully. That said, EPIPE situation is clearly one of 'ready for writing'. We don't have read-side issue because tcp_poll() already has read side shutdown care. | if (sk->sk_shutdown & RCV_SHUTDOWN) | mask |= POLLIN | POLLRDNORM | POLLRDHUP; So, Let's insert same logic in write side. - reference url http://blade.nagaokaut.ac.jp/cgi-bin/scat.rb/ruby/ruby-core/31065 http://blade.nagaokaut.ac.jp/cgi-bin/scat.rb/ruby/ruby-core/31068Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
As discovered by Anton Blanchard, current code to autotune tcp_death_row.sysctl_max_tw_buckets, sysctl_tcp_max_orphans and sysctl_max_syn_backlog makes little sense. The bigger a page is, the less tcp_max_orphans is : 4096 on a 512GB machine in Anton's case. (tcp_hashinfo.bhash_size * sizeof(struct inet_bind_hashbucket)) is much bigger if spinlock debugging is on. Its wrong to select bigger limits in this case (where kernel structures are also bigger) bhash_size max is 65536, and we get this value even for small machines. A better ground is to use size of ehash table, this also makes code shorter and more obvious. Based on a patch from Anton, and another from David. Reported-and-tested-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 8月, 2010 7 次提交
-
-
由 David S. Miller 提交于
As reported by Anton Blanchard when we use percpu_counter_read_positive() to make our orphan socket limit checks, the check can be off by up to num_cpus_online() * batch (which is 32 by default) which on a 128 cpu machine can be as large as the default orphan limit itself. Fix this by doing the full expensive sum check if the optimized check triggers. Reported-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net> Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
-
由 Dan Carpenter 提交于
Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc complain: drivers/net/pxa168_eth.c:657: warning: cast to pointer from integer of different size Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
The phy_mii_ioctl() function changed recently. It now takes a struct ifreq pointer directly. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
A couple issues here: * Some resources weren't released. * If alloc_etherdev() failed it would have caused a NULL dereference because "pep" would be null when we checked "if (pep->clk)". * Also it's better to propagate the error codes from mdiobus_register() instead of just returning -ENOMEM. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
"pep->pd" isn't checked consistently in this function. For example it's dereferenced unconditionally on the next line after the end of the if condition. This function is only called from pxa168_eth_probe() and pep->pd is always non-NULL so I removed the check. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Anton Vorontsov 提交于
It is possible that phylib will call adjust_link before returning from {,of_}phy_connect(), which may cause the following [very rare, though] oops upon reopening the device: Unable to handle kernel paging request for data at address 0x0000024c Oops: Kernel access of bad area, sig: 11 [#1] PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0 P1021 RDB Modules linked in: NIP: c0345dac LR: c0345dac CTR: c0345d84 TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0 [...] NIP [c0345dac] adjust_link+0x28/0x19c LR [c0345dac] adjust_link+0x28/0x19c Call Trace: [c0d25f00] [000045e1] 0x45e1 (unreliable) [c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554 [...] Here is why. Drivers store phydev in their private structures, e.g. gianfar driver: static int init_phy(struct net_device *dev) { ... priv->phydev = of_phy_connect(...); ... } So that adjust_link could retrieve it back: static void adjust_link(struct net_device *dev) { ... struct phy_device *phydev = priv->phydev; ... } If the device has been opened before, then phydev->state is set to PHY_HALTED (or undefined if the driver didn't call phy_stop()). Now, phy_connect starts the PHY state machine before returning phydev to the driver: phy_start_machine(phydev, NULL); if (phydev->irq > 0) phy_start_interrupts(phydev); return phydev; The time between 'phy_start_machine()' and 'return phydev' is undefined. The start machine routine delays execution for 1 second, which is enough for most cases. But under heavy load, or if you're unlucky, it is quite possible that PHY state machine will execute before phy_connect() returns, and so adjust_link callback will try to dereference phydev, which is not yet ready. To fix the issue, simply initialize the PHY's state to PHY_READY during phy_attach(). This will ensure that phylib won't call adjust_link before phy_start(). Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Heiko Carstens 提交于
Fix this error on an s390 allyesconfig build: linux-2.6/drivers/net/caif/caif_spi.c:98: undefined reference to `dma_free_coherent' Cc: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 8月, 2010 5 次提交
-
-
由 Neil Horman 提交于
If netconsole is in use, there is a possibility for deadlock in 3c59x between boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock, and if netconsole is in use, a pr_* call from the boomerang_interrupt routine will result in the netconsole code attempting to trnasmit an skb, which can try to take the same spin lock, resulting in deadlock. The fix is pretty straightforward. This patch allocats a bit in the 3c59x private structure to indicate that its handling an interrupt. If we get into the transmit routine and that bit is set, we can be sure that we have recursed and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so the stack requeues the skb to try again later. Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yinglin Luan 提交于
Function qlcnic_intr has pointer to qlcnic_host_sds_ring as second parameter not pointer to qlcnic_adapter. Signed-off-by: NYinglin Luan <synmyth@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yinglin Luan 提交于
Function netxen_intr has pointer to nx_host_sds_ring as second parameter not pointer to netxen_adapter. Signed-off-by: NYinglin Luan <synmyth@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Changli Gao 提交于
nf_bridge_alloc() always reset the skb->nf_bridge, so we should always put the old one. Signed-off-by: NChangli Gao <xiaosuo@gmail.com> Signed-off-by: NBart De Schuymer <bdschuym@pandora.be> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
commit f3c5c1bf (netfilter: xtables: make ip_tables reentrant) forgot to also compute the jumpstack size in the compat handlers. Result is that "iptables -I INPUT -j userchain" turns into -j DROP. Reported by Sebastian Roesner on #netfilter, closes http://bugzilla.netfilter.org/show_bug.cgi?id=669. Note: arptables change is compile-tested only. Signed-off-by: NFlorian Westphal <fw@strlen.de> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Tested-by: NMikael Pettersson <mikpe@it.uu.se> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 8月, 2010 2 次提交
-
-
由 Randy Dunlap 提交于
Why wouldn't kconfig symbol ISDN_DRV_AVMB1_B1PCMCIA also depend on PCMCIA? Fix build for PCMCIA not enabled: ERROR: "b1_free_card" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1ctl_proc_fops" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_reset_ctr" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_load_firmware" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_send_message" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_release_appl" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_register_appl" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_getrevision" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_detect" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_interrupt" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! ERROR: "b1_alloc_card" [drivers/isdn/hardware/avm/b1pcmcia.ko] undefined! Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Cc: Carsten Paeth <calle@calle.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Changli Gao 提交于
__packed is only defined in kernel space, so we should use __attribute__((packed)) for the code shared between kernel and user space. Two __attribute() annotations are replaced with __attribute__() too. Signed-off-by: NChangli Gao <xiaosuo@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 8月, 2010 2 次提交
-
-
由 Bruce Allan 提交于
From: Bruce Allan <bruce.w.allan@intel.com> The alternate MAC address feature is only supported by 80003ES2LAN and 82571 LOMs as well as a couple 82571 mezzanine cards. Checking for an alternate MAC address on other parts can fail leading to the driver not able to load. This patch limits the check for an alternate MAC address to be done only for parts that support the feature. This issue has been around since support for the feature was introduced to the e1000e driver in 2.6.34. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Reported-by: NFabio Varesano <fax8@users.sourceforge.net> Cc: stable@kernel.org Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>