This patch fixes cache memory parameter setting for the M32104 target.  So
far, its performance seemed to have been degraded due to incorrect cache
parameter setting.

  * arch/m32r/boot/setup.S: Set SFR(Special Fuction Registers) region
    to be non-cachable explicitly.
  * arch/m32r/mm/cache.c: Fix cache flushing routines not to switch off
    the M32104 cache.
Signed-off-by: NHayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Modify _port2addr*() routines in arch/m32r/kernel/io_*.c to use
NONCACHE_OFFSET instead of hard-coding of a constant address.

This modification is also required to support an M3A-ZA36 FPGA eva board in
case an MMU-less synthesizable m32r core is used.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch is for updating m32r's MMU-less support.

Some legacy MMU-less m32r chips cannot return from a trap handler to the
right-hand side 16-bit halfword code of a 32-bit instrucion code pair, because
a "trap" instruction specification was expanded in M32R-II ISA.

This modification forces "trap" instructions to be placed in word alignment
location with a parallel "nop" code.
Signed-off-by: NKazuhiro Inaoka <inaoka@linux-m32r.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch is for supporting a new target platform, Renesas M32104UT
evaluation board.

The M32104UT is an eval board based on an uT-Engine specification.  This board
has an MMU-less M32R family processor, M32104.
http://www-wa0.personal-media.co.jp/pmc/archive/te/te_m32104_e.pdf

This board is one of the most popular M32R platform, so we have ported
Linux/M32R to it.
Signed-off-by: NNaoto Sugai <Sugai.Naoto@ak.MitsubishiElectric.co.jp>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A trivial fix to remove unused instructions.
Signed-off-by: NNaoto Sugai <Sugai.Naoto@ak.MitsubishiElectric.co.jp>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We had a report from one loony user who tried out suspend to disk using a
swap partition on a firewire drive.  As the firewire thread was put to
sleep it didn't work out too well.
Signed-off-by: NDave Jones <davej@redhat.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ben Collins <bcollins@debian.org>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This makes the swsusp_info structure become the header of the image in the
literal sense (ie.  it is saved to the swap and read before any other image
data with the help of the swsusp's swap map structure, so generally it is
treated in the same way as the rest of the image).

The main thing it does is to make swsusp_header contain the offset of the swap
map used to track the image data pages rather than the offset of swsusp_info.
 Simultaneously, swsusp_info becomes the first image page written to the swap.

The other changes are generally consequences of the above with a few
exceptions (there's some consolidation in the image reading part as a few
functions turn into trivial wrappers around something else).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This changes the handling of swap partitions by swsusp to avoid locking of the
swap devices that are not used for suspend and, consequently, simplifies the
code.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds the function get_swap_page_of_type() allowing us to specify an index
in swap_info[] and select a swap_info_struct structure to be used for
allocating a swap page.

This function (or another one of similar functionality) will be necessary for
implementing the image-writing part of swsusp in the user space.   It can also
be used for simplifying the current in-kernel implementation of the
image-writing part of swsusp.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make the suspend image size limit tunable via /sys/power/image_size.

It is necessary for systems on which there is a limited amount of swap
available for suspend.  It can also be useful for optimizing performance of
swsusp on systems with 1 GB of RAM or more.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Limit the size of the suspend image to approx.  500 MB, which should
improve the overall performance of swsusp on systems with more than 1 GB of
RAM.

It introduces the constant IMAGE_SIZE that can be set to the preferred size
of the image (in MB) and modifies the memory-shrinking part of swsusp to
take this constant into account (500 is the default value of IMAGE_SIZE).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These two prototypes are already present in sched.h, remove duplicate
version.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change removes the old, deprecated interface from the opl3sa2 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files.  This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change removes the old, deprecated interface from the nm256 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files.  This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.

Note that this driver has been obsoleted by an ALSA equivalent.
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change removes the old, deprecated interface from the maestro driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files.  This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.

The check_suspend() function and associated logic was not removed, even though
it is now unnecessary.

Note that this driver has been obsoleted by an ALSA equivalent.
Acked-by: NZach Brown <zab@zabbo.net>
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change removes the old, deprecated interface from the cs46xx driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files.  This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.

Note this driver has PCI PM hooks which are set properly.  It also has the
ability to trigger suspend/resume from an ioctl.  This functionality was not
touched, though it could use a serious review if this driver continues to
persist in the mainline tree..

Note that this driver has been obsoleted by an ALSA equivalent.
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change removes the old, deprecated interface from the cs4281 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files.  This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.

Note that this driver has been obsoleted by an ALSA equivalent.

Note that this driver has hooks for PCI power management, but does not
implement the ->suspend()/->resume() methods.
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This change removes the old, deprecated interface from the ad1848 driver,
including the pm_{,un}register() calls, the local storage of the pmdev object
and the reference to the old header files.  This change is done to assist in
eradicating the users of the legacy interface so as to help facilitate the
removal of the interface itself.
Signed-off-by: NPatrick Mochel <mochel@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes a problem with the function enough_free_mem() used by
swsusp to verify if there is a sufficient number of memory pages available
to it to create and save the suspend image.

Namely, enough_free_mem() uses nr_free_pages() to obtain the number of free
memory pages, which is incorrect, because this function returns the total
number of free pages, including free highmem pages, and the highmem pages
cannot be used by swsusp for storing the image data.

The patch makes enough_free_mem() avoid counting the free highmem
pages as available to swsusp.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch makes swsusp free only as much memory as needed to complete the
suspend and not as much as possible.   In the most of cases this should speed
up the suspend and make the system much more responsive after resume,
especially if a GUI (eg.  X Windows) is used.

If needed, the old behavior (ie to free as much memory as possible during
suspend) can be restored by unsetting FAST_FREE in power.h
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch introduces the swap map structure that can be used by swsusp for
keeping tracks of data pages written to the swap.   The structure itself is
described in a comment within the patch.

The overall idea is to reduce the amount of metadata written to the swap and
to write and read the image pages sequentially, in a file-alike way.  This
makes the swap-handling part of swsusp fairly independent of its
snapshot-handling part and will hopefully allow us to completely separate
these two parts in the future.

This patch is needed to remove the suspend image size limit imposed by the
limited size of the swsusp_info structure, which is essential for x86-64
systems with more than 512 MB of RAM.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes the image encryption that is only used by swsusp instead of
zeroing the image after resume in order to prevent someone from reading some
confidential data from it in the future and it does not protect the image from
being read by an unauthorized person before resume.  The functionality it
provides should really belong to the user space and will possibly be
reimplemented after the swap-handling functionality of swsusp is moved to the
user space.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Kconfig tweaks and tons of deletions.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Thanks to Christoph for doing most of the work.

This allows automatic SMP IRQ affinity assignment other than default "all
interrupts on all CPUs" which is rather expensive.  This might be useful if
the hardware can be programmed to distribute interrupts among different
CPUs, like Alpha does.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With physical CPU hotplug, the CPU is hot removed and it should not receive
any interrupts.  Disabling interrupt is much safer.  This basically is what we
do in ia64 & x86.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NBen Collins <bcollins@ubuntu.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
  wire mode if there was an i8259 connected to it. This enables getting
  timer interrupts in second kernel in legacy mode.

o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
  to CPU0. This works well for kexec but not for kdump as we might crash
  on a different CPU and second kernel will not see timer interrupts.

o This patch modifies the redirection table entry to deliver the timer
  interrupts to the cpu we are rebooting (instead of hardcoding to zero).
  This ensures that second kernel receives timer interrupts even on a
  non-boot cpu.
Signed-off-by: NVivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

GCC 4.1 gives the following warning: include/asm/mpspec.h:79: warning:
`packed' attribute ignored for field of type `unsigned char'

The packed attribute isn't really necessary anyways so just remove it.
Signed-off-by: NBrian Gerst <bgerst@didntduck.org>
Acked-by: NDave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When we re-calibrate the frequency, it is likely that an interrupt (as for
example the main system clock) will be triggered by the system.  Therefore
the calibration may not be accurate.  This will also provide a fix to bug
#5266.

Many thanks to Larry Finger for helping resolving this issue.
Signed-off-by: NBruno Ducrot <ducrot@poupinou.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Fix screen blanking on BIOSes that return APM_NOT_ENGAGED when APM enabled
  screen blanking is not turned on.

  The original code only tried to set the state on device 0x100, and then
  0x1FF, and I added 0x101 to the mix too.

- Clean up logic in apm_console_blank().

- Prevent the error message from printing out twice.

Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support to hw_random for the Geode LX HRNG device.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Provide basic support for the AMD Geode GX and LX processors.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Removed the unused variable "rv".
Signed-off-by: NDaniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Removed the unused variable "rv".
Signed-off-by: NDaniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There is a single instruction on i386 to find largest set bit; so it makes
sense to use it (like we use bfs for ffs()).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Missing newline in printk.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The 'make rodata read-only' patch in -mm exposes a latent bug in the 32-bit
change_page_attr() function, which causes certain CPUs (Those with NX
basically) to reboot instantly after pages are marked read-only.

The same bug got fixed a while back on x86-64, but never got propagated to
i386.

Stuart Hayes from Dell also picked up on this last June, but it never got
fixed, as the only thing affected by it aparently was the nvidia driver.

Blatantly stealing description from his post..

"It doesn't appear to be fixed (in the i386 arch).  The
 change_page_attr()/split_large_page() code will still still set all the
 4K PTEs to PAGE_KERNEL (setting the _PAGE_NX bit) when a large page
 needs to be split.

 This wouldn't be a problem for the bulk of the kernel memory, but there
 are pages in the lower 4MB of memory that's free, and are part of large
 executable pages that also contain kernel code.  If change_page_attr()
 is called on these, it will set the _PAGE_NX bit on the whole 2MB region
 that was covered by the large page, causing a large chunk of kernel code
 to be non-executable."
Signed-off-by: NArjan van de Ven <arjan@infradead.org>
Signed-off-by: NDave Jones <davej@redhat.com>
Cc: <Stuart_Hayes@Dell.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If we are using hotplug enabled kernel, then make bigsmp the default mode.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When we bring up a new CPU via INIT/startup IPI messages, the CPU that's
coming up sends a xTPR message to the chipset.  Intel chipsets (at least)
don't provide any architectural guarantee on what the chipset will do with
this message.  For example, the E850x chipsets uses this xTPR message to
interpret the interrupt operating mode of the platform.  When the CPU
coming online sends this message, it always indicates that it is in logical
flat mode.  For the CPU hotplug case, the platform may already be
functioning in cluster APIC mode at this time, the chipset can get confused
and mishandle I/O device and IPI interrupt routing.

The situation eventually gets corrected when the new CPU sends another xTPR
update when we switch it to cluster mode, but there's a window during which
the chipset may be in an inconsistent state.  This patch avoids this
problem by using the flat physical interrupt delivery mode instead of
cluster mode for bigsmp (>8 cpu) support.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On architectures that implement sparsemem but not discontigmem we want to
be able to hide the flatmem option in some cases.  On ppc64 for example,
when we select NUMA we must not select flatmem.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>