BAR tx cmd tid was set to non qos (8). This is wrong as BAR
should be sent with the tid of the BA session.
This led to a corruption in the firmware. The visible
effect of this from the driver side is the BA notification
that comes back after the BAR. It was botched and led to the
WARNING below.

------------[ cut here ]------------
WARNING: CPU: 2 PID: 17707 at /home/tester/workspace_hostap/iwlwifi/drivers/net/wireless/iwlwifi/mvm/tx.c:976 iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]()
Q 4500, tid 8, flow 65535
Modules linked in: iwlmvm(O) mac80211(O) iwlwifi(O) cfg80211(O) compat(O) netconsole configfs ctr ccm arc4 autofs4 microcode bnep rfcomm snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_codec_generic snd_hda_intel joydev snd_hda_codec uvcvideo videobuf2_core snd_hwdep videodev snd_pcm videobuf2_vmalloc videobuf2_memops i915 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device drm_kms_helper dell_wmi dell_laptop drm btusb bluetooth snd psmouse i2c_algo_bit sparse_keymap wmi soundcore 6lowpan_iphc dcdbas serio_raw video lpc_ich ppdev mac_hid parport_pc nfsd nfs_acl auth_rpcgss nfs fscache binfmt_misc lockd sunrpc lp parport msdos sdhci_pci sdhci mmc_core ahci libahci e1000e ptp pps_core [last unloaded: compat]
CPU: 2 PID: 17707 Comm: irq/46-iwlwifi Tainted: G        W  O 3.14.17-patched #4
Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012
 00000000 00000000 ebd49d6c c1616221 f985dbdc ebd49d9c c1044e44 f9861df4
 ebd49dc8 0000452b f985dbdc 000003d0 f98395da f98395da ebd49f10 eaf3d8a4
 0000ffff ebd49db4 c1044f03 00000009 ebd49dac f9861df4 ebd49dc8 ebd49e64
Call Trace:
 [<c1616221>] dump_stack+0x41/0x52
 [<c1044e44>] warn_slowpath_common+0x84/0xa0
 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<c1044f03>] warn_slowpath_fmt+0x33/0x40
 [<f98395da>] iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
 [<c10e9767>] ? trace_buffer_unlock_commit+0x37/0x50
 [<f98568a3>] ? iwl_tm_mvm_send_rx+0x53/0x90 [iwlmvm]
 [<f98327a8>] iwl_mvm_rx_dispatch+0x108/0x130 [iwlmvm]
 [<f9eac7e7>] iwl_pcie_irq_handler+0xf17/0x15b0 [iwlwifi]
 [<c10994c1>] irq_thread_fn+0x21/0x50
 [<c109926c>] irq_thread+0xec/0x110
 [<c10994a0>] ? irq_thread_dtor+0xb0/0xb0
 [<c10993f0>] ? irq_finalize_oneshot.part.34+0xc0/0xc0
 [<c1099180>] ? wake_threads_waitq+0x40/0x40
 [<c1062fdb>] kthread+0x9b/0xb0
 [<c1627137>] ret_from_kernel_thread+0x1b/0x28
 [<c1062f40>] ? flush_kthread_worker+0x90/0x90
---[ end trace 5e0f67374816db17 ]---
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This change has already been implemented in iwldvm:

commit a260e7b3f0307878b99d57ed1406cf2d497923b8
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Sun Oct 5 09:11:14 2014 +0300

    iwlwifi: dvm: drop non VO frames when flushing

Since I added the flush() callback implementation in mvm,
we got reports that the queues are stuck while roaming
or suspending.
This commit above helped much for iwldvm, implement the
same behavior for iwlmvm.

CC: <stable@vger.kernel.org> [3.16+]
Fixes: c5b0e7c0 ("iwlwifi: mvm: implement mac80211's flush callback")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

EBS error detection isn't supported by all FWs, so turn it on
only if the FW advertises such support.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows 3160 / 7260 / 7265 / 7265D / 8000 devices to
use the latest version of the firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.

This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a flag that enables match found notification to align with
FW API change.

Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When tid_tspec was set to IWL_TID_NON_QOS (8) this led to an
out of bounds access to the tid_to_mac80211_ac array whose size
is 7. Fix this.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

commit 5c904224
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).

Fixes: 5c904224 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Cc: Stable <stable@vger.kernel.org>  [3.16+]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We were advertising iwlwifi-7265-X.ucode instead of
iwlwifi-7265D-X.ucode. Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The trans cfg was not replaced for 7265-D cards. This led to a check of
the min-NVM version against a 7265-C card, causing very-old 7265-D cards
to operate incorrectly with the driver.

Fixes: 3fd0d3c1 ("iwlwifi: pcie: support 7265-D devices")
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New FW has chunks that are larger than the size limit of the
FH's DMA. To make sure we don't crash it - actively limit the
max size of each chunk.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A few device IDs were added, reflect this change in the
driver.

Cc; <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the very unlikely case in which no firmware could be,
found. the same pointer was freed twice. Fix that.

Fixes: 490fefeb ("iwlwifi: define the .ucode file format for debug")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we reset the device, the CSR_INT gets cleared as well
as CSR_INT_MASK. Meaning that we shouldn't get any interrupt
but, due to a hardware bug, recent devices will keep sending
interrupts. This leads to an interrupt storm while stopping
the device.
The way to fix this is to ACK all the interrupts after the
device is reset so that the value of CSR_INT will stay
0xffffffff.

Fixes: 522713c8 ("iwlwifi: pcie: properly reset the device")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

On stop(), we already cleared our internal state,
and the restart_complete() callback won't be
called, so simply clear the IN_HW_RESTART flag.

Keeping the flag might result in invalid state
on the next start(), preventing the driver starting
properly.

Additionally, don't take IWL_MVM_REF_UCODE_DOWN on stop()
if hw restart was requested, as the ref was already
taken in this case.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Generally broadcast mac address deauth is followed by stop_ap or start_ap.
In both cases, FW already has provision to send deauth; so there is no
need to handle broadcast mac deauthentication.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Station node entries should be guarded for whole of their reference
instead of just while getting node entry from station list.
It may happen that station node is retrieved may be deleted by
deauthentication event while it is still in use.

Reported by: Tim Shepard <shep@xplot.org>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support to delete peer station's RA lists
upon station deautheticate event on AP interface. Patch also
decrements TX pending count upon removing packets from RA list.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A crash was observed while cfg80211 del_station handler is
called while stopping AP. This was happening because we were
deleting station list and Rx reorder table entries in del_sta
handler. While station entry is being deleted here, it may happen
that station deauth event from FW would also try to delete station
entry.

This patch fixes this crash by not deleting station entries in del_station
handler. Entry would be deleted while processing station deauth event; which
is triggered by del_station command to FW.

Reported by: Tim Shepard <shep@xplot.org>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for multiple BSS interfaces (AP). In
total three AP configurations can be created. In order to use
multiple BSS firmware needs to support it.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor specific commands was always using main interface,
change this to use the by caller supplied interface.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use single message MSI to replace legacy interrupt.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some 43602 devices are band specific and identify themselves
with different PCIE device ID. This patch adds support for the
43602 2.4G and 5.0G devices used in for example R8000 router.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ifidx provided by FW needs to be offsetted when receiving data
packets.

Cc: stable@vger.kernel.org # v3.17, v3.18
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: stable@vger.kernel.org # v3.17, v3.18
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new ucode package format holds also the usniffer images
(in addition to the operational images and the TLVs).
The driver can load the usniffer image if debug
configuration tells it to.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Until this patch, dumping the monitor data could be done only
for PCIe external (DRAM) mode in 7000 HW family. This patch
allows to pull the monitor data also on other families, and
also to pull the monitor data if an internal buffer is used.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send all debug-configuration HCMDs that are set in the TLVs
to the FW. This may include HCMDs to configure the FW
monitor and FW log level, for example.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Debug information can be appended to the firmware file. This
information will be used by the driver to enable / disable
debugging features in the firmware.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Interoperability issues were identified and root caused to
the Smart Fifo watermarks. These issues arose with
NetGear R7000. Fix this.

Cc: <stable@vger.kernel.org> [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:

Loaded firmware version: 8.24.2.2
Start IWL Error Log Dump:
Status: 0x0000004C, count: 5
0x00000004 | NMI_INTERRUPT_WDG
0x000006F4 | uPc
0x000005BA | branchlink1
0x000006F8 | branchlink2
0x000008C2 | interruptlink1
0x00005B02 | interruptlink2
0x00000002 | data1
0x07030000 | data2
0x00000068 | line
0x3E80510C | beacon time
0x728A0EF4 | tsf low
0x0000002A | tsf hi
0x00000000 | time gp1
0x01BDC977 | time gp2
0x00000000 | time gp3
0x00010818 | uCode version
0x00000000 | hw version
0x00484704 | board version
0x00000002 | hcmd
0x2FF23080 | isr0
0x0103E000 | isr1
0x0000001A | isr2
0x1443FCC3 | isr3
0x11800112 | isr4
0x00000068 | isr_pref
0x000000D4 | wait_event
0x00000000 | l2p_control
0x00000007 | l2p_duration
0x00103040 | l2p_mhvalid
0x00000007 | l2p_addr_match
0x00000000 | lmpm_pmg_sel
0x00000000 | timestamp
0x00000200 | flow_handler

This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961

Cc: <stable@vger.kernel.org>
Fixes: a0855054 ("iwlwifi: dvm: drop non VO frames when flushing")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In 8000 B-step the FW file has changed, but by the time we
know the HW step, the FW file is already requested.

This patch defaults 8000 family to B-step if no HW step is
detected in time. When it can it checks what HW step it
really is (in 8000 family) and if it isn't B-step, the FW
file is released and the A-step file is requested.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix the 4165 series name that was called 4265 by mistake.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Hardware doesn't place any restrictions on the buffer alignment,
consider this TODO resolved.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.

Rate-limit it to prevent dmesg flooding.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some compilation environments, result of pointer arithmetic interpreted as int
while in others it is long int. Force conversion to long.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>