This patch tweaks the init timing of the driver just a little bit to
increase stability on load/unload and SR-IOV enable/disable cycles.

First, run the init_task loop a little quicker in order to reduce
overall init time.

Second, stagger the start of the init task based on the device's
PCIe function ID. This lessens the impact on the firmware when a
whole bunch of VFs are initialized simultaneously, e.g. enabling
SR-IOV without the VF driver blacklisted. For single VFs assigned
to VMs this will have no effect as the function ID will always be 0.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Down was requesting queue disables, but then exited immediately without
waiting for the queues to actually disable. This could allow any
function called after i40evf_down to run immediately, including
i40evf_up, and causes a memory leak.

This issue has been fixed in a recent refactor of the reset code, but
add a couple WARN_ONs in the slow path to help us recognize if we
reintroduce this issue or if we missed any cases.

Change-ID: I27b6b5c9a79c1892f0ba453129f116bc32647dd0
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The interrupt enable function was always making the caller add
the base_vector from the VSI struct which is already passed to
the function. Just collapse the math into the helper function.

Change-ID: I54ef33aa7ceebc3231c3cc48f7b39fd0c3ff5806
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to performance reasons, VEB stats have been disabled in the hw. This
patch adds code to check for that condition before accumulating these
stats.

Change-ID: I7d805669476fedabb073790403703798ae5d878e
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add new device id and support for another 20Gb device.

Change-ID: Ib1b61e5bb6201d84953f97cade39a6e3369c2cf2
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a useless message that blathers on whenever a vxlan port is deleted.

Change-ID: If63fb8cf38e56cf433b68e498f11389de51919ba
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't let the debugfs register read and write commands try to access
outside of the ioremapped space.  While we're at it, remove the use of
a misleading constant.

Change-ID: Ifce2893e232c65c7a76c23532c658f298218a81b
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In i40e_ndo_set_vf_port_vlan, we were using the QOS value
inconsistently, sometimes shifting it, sometimes not. Do the shift-and-
or operation correctly, once, and use the result consistently everywhere
in the function.

Change-ID: I46f062f3edc90a8a017ecec9137f4d1ab0ab9e41
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e rx_dropped counter was not showing up in netstat -i.
Add the right counter to be updated with the stats.

Change-ID: I4dd552e9995836099184f9d9a08e90edb591155f
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The arm writeback (arm_wb) code is used for kicking the Tx ring to
make sure any pending work is completed even if interrupts are
disabled. It was running when it didn't need to, and not clearing
the ring->arm_wb state after it was set.  This caused Tx hangs
to still occur occasionally when there really was no hang.
Fix this by resetting the variable right after it was used.

Change-ID: I7bf75d552ba9c4bd203d40615213861a24bb5594
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The struct i40e_aqc_get_cee_dcb_cfg_v1_resp was originally defined with
word boundary layout issues, which most compilers deal with by silently
adding padding, making the actual struct larger than designed.
This patch adds an extra byte in fields reserved3 and reserved4 to directly
acknowledge that padding.

Because the struct doesn't actually change in size or layout, this doesn't
constitute a change in the API.

Change-ID: I53fa4741b73fa255621232a85fba000b0e223015
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a port VLAN is set for a given virtual function (VF) before the VF
driver is loaded then a configuration error results in which the port
VLAN is ignored when the VF driver is subsequently loaded.  This causes
the VF's MAC/VLAN filters to not use the correct VLAN filter.  This
patch ensures that the port VLAN filter is considered at the right time
during configuration of the VF's MAC/VLAN filters.

Change-ID: I28f404cbc21a4c6d70a7980b87c77f13f06685a4
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The error code sent into i40e_aq_rc_to_posix() are signed values, so we
really need to treat them as such.

Change-ID: I3d1ae0ee9ae0b1b6f5fc424f8b8cc58b0ea93203
Reported-by: NHelin Zhang <helin.zhang@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NVasily Averin <vvs@virtuozzo.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NVasily Averin <vvs@virtuozzo.com>
Tested-by: NAndrews Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to the notifier_call callback of a notifier_block, change the
function signature of switchdev add and del operations to:

    int switchdev_port_obj_add/del(struct net_device *dev,
                                   enum switchdev_obj_id id, void *obj);

This allows the caller to pass a specific switchdev_obj_* structure
instead of the generic switchdev_obj one.

Drivers implementation of these operations and switchdev have been
changed accordingly.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to the notifier_call callback of a notifier_block, change the
function signature of switchdev dump operation to:

    int switchdev_port_obj_dump(struct net_device *dev,
                                enum switchdev_obj_id id, void *obj,
                                int (*cb)(void *obj));

This allows the caller to pass and expect back a specific
switchdev_obj_* structure instead of the generic switchdev_obj one.

Drivers implementation of dump operation can now expect this specific
structure and call the callback with it. Drivers have been changed
accordingly.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The net_device associated to a dump operation does not have to be passed
to the callback. switchdev stores it in a superset struct, if needed.

Also some drivers (such as DSA drivers) may not have easy access to it.

This will simplify pushing the callback function down to the drivers.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_HPLANCE=m and CONFIG_NET_POLL_CONTROLLER=y:

    ERROR: "lance_poll" [drivers/net/ethernet/amd/hplance.ko] undefined!

Add the missing export to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The modular driver supports only one card, just like the built-in
driver.

Note that this limitation is a problem which affects all Nubus card
drivers, because they have to do all their own bus matching, because
Nubus still lacks the necessary driver model support.
Suggested-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit dea87024 ("dsa: mv88e6xxx: Allow speed/duplex of port to be
configured") leads to the following static checker warning:

        drivers/net/dsa/mv88e6xxx.c:585 mv88e6xxx_adjust_link()
        warn: unsigned 'ret' is never less than zero.

drivers/net/dsa/mv88e6xxx.c
   573  void mv88e6xxx_adjust_link(struct dsa_switch *ds, int port,
   574                             struct phy_device *phydev)
   575  {
   576          struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
   577          u32 ret, reg;
   578
   579          if (!phy_is_pseudo_fixed_link(phydev))
   580                  return;
   581
   582          mutex_lock(&ps->smi_mutex);
   583
   584          ret = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_PCS_CTRL);
   585          if (ret < 0)

Make ret an int, which is the return type for _mv88e6xxx_reg_read()
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move remaining structs to VRF driver and delete the vrf header file.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename IFF_VRF_MASTER to IFF_L3MDEV_MASTER and update the name of the
netif_is_vrf and netif_index_is_vrf macros.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some embedded systems the EEPROM does not contain a valid MAC address.
In that case it is better to fallback to a generated mac address and
let init scripts fix the value later.
Reported-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
[Changed handcoded setup to use eth_hw_addr_random() and to save new address into HW]
Signed-off-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the switch to per-CPU interrupts, we lost the ability to set which
CPU was going to receive our RX interrupt, which was now only the CPU on
which the mvneta_open function was run.

We can now assign our queues to their respective CPUs, and make sure only
this CPU is going to handle our traffic.

This also paves the road to be able to change that at runtime, and later on
to support RSS.

[gregory.clement@free-electrons.com]: hardened the CPU hotplug support.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvneta driver allows to change the default RX queue trough the rxq_def
kernel parameter.

However, the current code doesn't allow to have any value but 0. It is
actively checked for in the driver's probe because the drivers makes a
number of assumption and takes a number of shortcuts in order to just use
that RX queue.

Remove these limitations in order to be able to specify any available
queue.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that our interrupt controller is allowing us to use per-CPU interrupts,
actually use it in the mvneta driver.

This involves obviously reworking the driver to have a CPU-local NAPI
structure, and report for incoming packet using that structure.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.

However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.

This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MPIC driver currently has a list of interrupts to handle as per-cpu.

Since the timer, fabric and neta interrupts were the only per-cpu
interrupts in the system, we can now remove the switch and just check for
the hardware irq number to determine whether a given interrupt is per-cpu
or not.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for ethtool get time stamp ioctl, which is used by
tcpdump to get the supported time stamp types

eg: tcpdump -i eth5 -J
Time stamp types for eth5 (use option -j to set):
  host (Host)
  adapter_unsynced (Adapter, not synced with system time)

Adds support for adapter unsynced mode, by adding SIOCSHWTSTAMP support
in driver.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the compilation error with arm allmodconfig, this error
generated due to unavailability of readq() on 32-bit platform which was
found during net-next daily compilation. In the same time, fix all the
hns drivers compilation warnings.
Signed-off-by: Nhuangdaode <huangdaode@hisilicon.com>
Signed-off-by: Nzhaungyuzeng <Yisen.zhuang@huawei.com>
Signed-off-by: Nkenneth Lee <liguozhu@hisilicon.com>
Signed-off-by: Nyankejian <yankejian@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert pxaficp_ir to dmaengine. As pxa architecture is shifting from
raw DMA registers access to pxa_dma dmaengine driver, convert this
driver to dmaengine.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Tested-by: NPetr Cvek <petr.cvek@tul.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the pxa IRDA driver to readl and writel primitives, and remove
another set of direct registers access. This leaves only the DMA
registers access, which will be dealt with dmaengine conversion.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Tested-by: NPetr Cvek <petr.cvek@tul.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using directly the OS timer through direct register access,
use the standard sched_clock(), which will end up in OSCR reading
anyway.

This is a first step for direct access register removal and machine
specific code removal from this driver.

This commit changes the behavior, as previously the minimum turnaround
time was counted in 76ns steps, while with this patch it is counted in
microsecond steps. The strictly equal formula would have been :
	    while ((sched_clock() - si->last_clk) * 76 < mtt)
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to have FEATURES_NEED_QUIESCE defined as we
can simply use NETIF_F_RXCSUM instead as done in other parts
of the driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx_suspend() may return non-zero from lan78xx_write_reg() in some scenario.
Fix to return 0 when lan78xx_suspend() has no error.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>