Query the wakeup reasons properly and then
report them to mac80211.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement proper WoWLAN wakeup and query the wakeup
reasons, then report them to userspace.

Note that this is tricky: a firmware bug (that has
been fixed in later versions) means that the status
command response isn't properly closed in hardware
and thus won't arrive at the host. Sending another
command after it closes the status response but the
next command gets stuck, etc. We reset the device
after querying though, so this is not a big issue,
just makes for strange code.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using the non-atomic version creates a dependency between
mac80211's iflist_mtx and mvm->mutex. Use the atomic version
instead which doesn't take iflist_mtx but can't sleep, so
send the HCMD in ASYNC.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Internally, 64-bit byte counters maintained for per-station
statistics. Tell to the netlink that full 64-bit value provided
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In commit 0d2e7a5c (wireless: Remove unnecessary alloc/OOM messages,
alloc cleanups) OOM messages after alloc were removed from the wlcore
modules.

Commit afb43e6d (wlcore: remove if_ops from platform_data)
reintroduced a couple of those.  This patch removes them.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

0x06f8, 0xe036 Hercules  Wireless Dual Band 600 USB Key HWNUm-600
0x0b05, 0x17a7 ASUS      USB-N10H 150Mbps 11n Wireless USB dongle
0x0df6, 0x0069 Sitecom   Wireless Dualband Network Adapter 300N X5 WLA-5000
0x0df6, 0x006f Sitecom   WiFi USB adapter N600 WLA-5100
0x13d3, 0x3340 AzureWave 802.11n USB Wireless LAN Card
0x13d3, 0x3399 AzureWave 802.11n USB Wireless LAN Card
0x13d3, 0x3400 AzureWave 802.11n USB Wireless LAN Card
0x13d3, 0x3401 AzureWave 802.11n USB Wireless LAN Card
0x1740, 0x0600 EnGenius  Dual-Band Wireless Media Adapter
0x1740, 0x0602 EnGenius  802.11 a/b/g/n Wireless USB Adapter
0x177f, 0x0254 Sweex     LW054 Wireless 54G Adapter USB
0xf201, 0x5370 TP-LINK   54Mbps Wireless USB Adapter

no RF3053, and I believe no RT5572.

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds PCIe8897 support to mwifiex.
In PCIe8897 PFU (pre-fetch unit) is enabled by default.
This patch adds support to accommodate this feaure as well.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch defines PCIe ring buffer array pointer as void instead
of mwifiex_pcie_buf_desc. This will enable us to use same pointers
for ring operations instead of new structures if buffer descriptor
structure changes.

Also split out event buffer descriptor structure from struct
mwifiex_pcie_buf_desc. For PCIe8766 TX/RX buffer descriptor is
same as evevt buffer descriptor. Newer chips could use different
TX/RX buffer descriptor while event descriptor remains the same.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch separates PCIe ring initialization from ring creation
routines. This modularizes ring creation(TXBD, RXBD and event
rings) functions.

Readability has been improved while moving the code around.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for storing PCIe device specific data
into driver_data structure of pci_device_id. When a device with
known device_id is probed, we use this driver_data to populate
card specific structres in driver.
This enables to remove device specific defines for scratch
registers, firmware name, FW download block size, etc. from
source code.

This will make addition of support for new chipsets a lot easier.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On joining an existing IBSS network, beaconing has to start
only after a TSF sync has happened by receiving a beacon from
the BSS. In creator mode, beaconing can start immediately after
a HW reset has been done.

Now that mac80211 notifies the driver of the mode type (creator/joiner)
via ieee80211_bss_conf->ibss_creator, make use of it to properly setup
the HW beacon timers.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a few places where the station's HT capabilities
should be checked instead of ATH9K_HW_CAP_HT, which is a global
feature for the driver. Fix this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.

From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The MEI bus API changed according to the latest comments from the char-misc
maintainers, and this patch fixes the microread mei physical layer code
according to those changes:
We pass the MEI id back to the probe routine, and the mei_driver takes a
table of MEI ids instead of one static id.
Also, mei_bus_driver got renamed to mei_driver, mei_bus_client to
mei_device, and mei_bus_set/get_clientdata to mei_set/get_clientdata.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

inet6_dev->lock can be taken from a timer. Disabled bottom
halves when we take it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a TKIP key is updated with a station pointer that is NULL it is
a GTK, so it should use the AP's station ID. Fix the code to do that.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fixes an issue that smatch pointed out:

  1118
  1119          key_flags = cpu_to_le16(keyconf->keyidx &  STA_KEY_FLG_KEYID_MSK);
                                        ^^^^^^^^^^^^^^^
This is s8.
                                                          ^^^^^^^^^^^^^^^^^^^^^
STA_KEY_FLG_KEYID_MSK is 0x300.

The result after the bitwise AND is always zero because 0xff & 0x300.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The TE_P2P_DEVICE_DISCOVERABLE time event type used for ROC is
assigned low priority in the FW, and thus has low chance of
being scheduled when there are active BSS or GO VMACs (even if
fragmentation is allowed). This is mainly problematic in for
cases where ROC is requested for sending action frames.

To overcome this, use a time event type that has priority equal
to that ot the time event type used by the FW to action scan.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The FW scheduler, schedules the bindings over a session of 128
fragments (each is 4 TU long). The quota command should allocate
all the session fragments between all the bindings that require quota
allocation. Currently, use static allocation, where the fragments
are equally distributed between all data bindings.

Note, that not allocating all the session's fragments might cause
the FW scheduler to leave the medium unused.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A new model of the RTL8188CUS has appeared.
Reported-and-tested-by: NThomas Rosenkrantz <tom.rosary@googlemail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this patch off-channel action frames can be transmitted. This
is needed for p2p when two devices need to find each other while
using different social channels.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently netdev gets created possibly after returning from
add_virtual_intf. This is because add_if is handled asynch. This
is wrong and netdev should be up before returning.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove some unused defines and comments. Also use same define
for IE length.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When adding a virtual interface cfg80211 already has taken the
rtnl_lock. So when the netdevice is being registered the
register_netdevice should be used instead of register_netdev.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently there is a sleep after disconnect on del_station. This
timeout is not needed (anymore) and is causing problems with p2p
setup, because remote side disconnects then supplicant will do
del_station and while it waits the 400ms remote side will already
reconnect and that is something supplicant cant handle.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wiphy object holds information about possible netdev
combinations which can be supported. This needs updating for
p2p device. Also p2p device netdev has wrong 80211 iftype.
Limit the change interface support to match the netdev
configuration/combination possibilities.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All interfaces for ifidx is 0 are created ahead and therefor
double registrations for not only bssidx 0, but ifidx 0 should
be ignored in brcfm_add_if.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the stored role in wdev struct to determine AP/GO role. This
simplifies code. Fix stop_ap for GO role.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add module variable with which a p2p0 netdev can be created. This
netdev can be used by wpa-supplicant to configure and set up the
p2p client/GO.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211 api change needs to be applied. this change will be squashed
with introducing commit:

commit 68751daec95b07a74b18aa22b2f9c196991dbe81
Author: Hante Meuleman <meuleman@broadcom.com>
Date:   Mon Nov 26 12:21:27 2012 +0100

    brcmfmac: add support for P2P listen mode.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some rare situations the wpa_supplicant can lock up on a remain
on channel command. Use actual cookies for the remain on channel
related commands and allow for additional remain on channel while
still having one set.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this patch it is possible to send action frames.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Once wpa_supplicant has registered for P2P action frames all received
action frames for the device are passed up to cfg80211.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this update it is possible to create an P2P go. Handle the
p2p go role in creation and the update beacon from cfg80211. Also
store primary bss in global struct. Needed to map cfg device
back to primary device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In preparation of p2p connections update the sta connect setup and
handling routines. Use join iovar and bsscfg commands where
applicable. Handle assoc ind per bsscfg (vif) and generalize
vndr ie setup to support assoc IEs and support all setup types,
e.g. sta, ap and p2p.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mask is OR-ed with value in case of deregister. Should
be AND-ed.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for changing existing interface into p2p go
interface.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>