While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.

This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.

ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.

Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.

Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.

Cc: stable@kernel.org
Tested-by: NSujith <m.sujith@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.

I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2

Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.

Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.

Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.

In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).

Cc: stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.

Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.

Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

USB devices do not require the chip test routine.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove some obvious looking dead code and rename few functions
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 0ce3bcfc.

Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period

Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And add the copyright/license header.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().

This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.

Cc: stable <stable@kernel.org>
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For the AR9002, the spur frequency read from the EEPROM is mangled
before being compared against AR_NO_SPUR.  This results in the driver
trying to set up the spur mitigation for bogus spurs, rather than
cleanly breaking out.
Signed-off-by: NBrian Prodoehl <bprodoehl@nomadio.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disabling BH is not required while running from a tasklet context
and so replace spin_lock_bh with just spin_lock.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It looks like some hardware registers are left into undefined state
after suspend/resume. At minimum, this can cause odd issues related to
key cache and hardware trying to encrypt/decrypt frames unexpectedly.
This seems to happen even when there is no keys configured, i.e., hardware
can end up touching TX frames just based of invalid key cache context
even if the driver is not asking a specific entry to be used. In
addition, RX can likely be affected. This patch fixes this issue.
Signed-off-by: NJouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recently added warning message on power change failure
is not needed on device removal.

ath: Failed to wakeup in 500us
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/hw.c:1618
ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]()
Hardware name: 64756D6
Pid: 540, comm: kworker/u:3 Not tainted 2.6.37-rc6-wl #37
Call Trace:
 [<ffffffff810501aa>] warn_slowpath_common+0x7a/0xb0
 [<ffffffffa056e280>] ? ath9k_iowrite32+0x0/0x90 [ath9k]
 [<ffffffff810501f5>] warn_slowpath_null+0x15/0x20
 [<ffffffffa05226ef>] ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]
 [<ffffffffa05700e5>] ath9k_ps_wakeup+0x85/0xd0 [ath9k]
 [<ffffffffa0570685>] ath9k_configure_filter+0x25/0x80 [ath9k]
 [<ffffffffa04dde43>] ieee80211_configure_filter+0x133/0x190 [mac80211]
 [<ffffffffa04ee502>] ieee80211_do_stop+0x132/0x540 [mac80211]
 [<ffffffff813466ff>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff812b6923>] ? dev_deactivate+0x1c3/0x1e0
 [<ffffffffa04ee925>] ieee80211_stop+0x15/0x20 [mac80211]
 [<ffffffff8129d1b6>] __dev_close+0x56/0x90
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.

For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>