When DMA is enabled (with hardware flow control enabled) the FIFO size
must be set to the size of the DMA buffer, as this is the size the tty
subsystem can use.
Signed-off-by: NHector Palacios <hector.palacios@digi.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.

Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d063)
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When configured with UART_16550_COMPATIBLE=NO or in versions prior to
the introduction of this option, the Designware UART will ignore writes
to the LCR if the UART is busy.  The current workaround saves a copy of
the last written LCR and re-writes it in the ISR for a special interrupt
that is raised when a write was ignored.

Unfortunately, interrupts are typically disabled prior to performing a
sequence of register writes that include the LCR so the point at which
the retry occurs is too late.  An example is serial8250_do_set_termios()
where an ignored LCR write results in the baud divisor not being set and
instead a garbage character is sent out the transmitter.

Furthermore, since serial_port_out() offers no way to indicate failure,
a serious effort must be made to ensure that the LCR is actually updated
before returning back to the caller.  This is difficult, however, as a
UART that was busy during the first attempt is likely to still be busy
when a subsequent attempt is made unless some extra action is taken.

This updated workaround reads back the LCR after each write to confirm
that the new value was accepted by the hardware.  Should the hardware
ignore a write, the TX/RX FIFOs are cleared and the receive buffer read
before attempting to rewrite the LCR out of the hope that doing so will
force the UART into an idle state.  While this may seem unnecessarily
aggressive, writes to the LCR are used to change the baud rate, parity,
stop bit, or data length so the data that may be lost is likely not
important.  Admittedly, this is far from ideal but it seems to be the
best that can be done given the hardware limitations.

Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
avoids the possibility of a "serial8250: too much work for irq" lock up.
This problem is rare in real situations but can be reproduced easily by
wiring up two UARTs and running the following commands.

  # stty -F /dev/ttyS1 echo
  # stty -F /dev/ttyS2 echo
  # cat /dev/ttyS1 &
  [1] 375
  # echo asdf > /dev/ttyS1
  asdf

  [   27.700000] serial8250: too much work for irq96
  [   27.700000] serial8250: too much work for irq96
  [   27.710000] serial8250: too much work for irq96
  [   27.710000] serial8250: too much work for irq96
  [   27.720000] serial8250: too much work for irq96
  [   27.720000] serial8250: too much work for irq96
  [   27.730000] serial8250: too much work for irq96
  [   27.730000] serial8250: too much work for irq96
  [   27.740000] serial8250: too much work for irq96
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the printk() calls to to dev_*() instead, to tie into the dynamic
debugging infrastructure.

Also change some "raw" printk() calls to dev_err() to provide a better
error message to userspace so it can properly identify the device and
not just have to guess.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ben Herrenschmidt found that commit 928bea96 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.

The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.

Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.

Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.

That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds code to initialize the DMA buffer to compensate for
possible hardware data corruption.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
[wsa: changed to use 'sizeof']
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NRob Clark <robdclark@gmail.com>

We still need an API exported by msm iommu driver (but not visible in
any public header anymore).  For now, just declare the prototype
ourselves, but when msm iommu driver provides a better option, use that
instead.
Signed-off-by: NRob Clark <robdclark@gmail.com>

The include file has been removed and the file does not
need it anyway, so remove it. Fixes a compile error.
Signed-off-by: NJoerg Roedel <joro@8bytes.org>
Signed-off-by: NRob Clark <robdclark@gmail.com>

The variable priv->kms is not initialized yet.

Found by "scripts/coccinelle/tests/odd_ptr_err.cocci".
PTR_ERR should access the value just tested by IS_ERR.
Signed-off-by: NThomas Meyer <thomas@m3y3r.de>

The stub for dw8250_probe_acpi() is missing an argument.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel BayTrail has two HS-UARTs with 64 byte fifo, support
for DMA and support for 16750 compatible Auto Flow Control.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.
Signed-off-by: NChew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: NThierry Reding <treding@nvidia.com>
[wsa: added marker to #endif]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

commit d16933b3 "i2c: s3c2410: Move
location of clk_prepare_enable() call in probe function" refactored
clk_enable and clk_disable calls yet neglected to remove the
clk_disable_unprepare call in the module's remove().

It helps remove warnings on an arndale during unbind:

echo 12c90000.i2c > /sys/bus/platform/devices/12c90000.i2c/driver/unbind

------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Not tainted 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c4a64>] (clk_disable+0x18/0x24)
[<c02c4a64>] (clk_disable+0x18/0x24) from [<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70)
[<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a6 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:751 clk_unprepare+0x14/0x1c()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Tainted: G        W    3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c5834>] (clk_unprepare+0x14/0x1c)
[<c02c5834>] (clk_unprepare+0x14/0x1c) from [<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70)
[<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a7 ]---
Signed-off-by: NKim Phillips <kim.phillips@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The DLink DWA-125 Rev D1 also uses this driver.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: NSergey Kostanbaev <sergey.kostanbaev@gmail.com>
Tested-by: NSergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PCI id for Intel Merrifield
Signed-off-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

	There's a bunch of failure exits in ffs_fs_mount() with
seriously broken recovery logics.  Most of that appears to stem
from misunderstanding of the ->kill_sb() semantics; unlike
->put_super() it is called for *all* superblocks of given type,
no matter how (in)complete the setup had been.  ->put_super()
is called only if ->s_root is not NULL; any failure prior to
setting ->s_root will have the call of ->put_super() skipped.
->kill_sb(), OTOH, awaits every superblock that has come from
sget().

Current behaviour of ffs_fs_mount():

We have struct ffs_sb_fill_data data on stack there.  We do
	ffs_dev = functionfs_acquire_dev_callback(dev_name);
and store that in data.private_data.  Then we call mount_nodev(),
passing it ffs_sb_fill() as a callback.  That will either fail
outright, or manage to call ffs_sb_fill().  There we allocate an
instance of struct ffs_data, slap the value of ffs_dev (picked
from data.private_data) into ffs->private_data and overwrite
data.private_data by storing ffs into an overlapping member
(data.ffs_data).  Then we store ffs into sb->s_fs_info and attempt
to set the rest of the things up (root inode, root dentry, then
create /ep0 there).  Any of those might fail.  Should that
happen, we get ffs_fs_kill_sb() called before mount_nodev()
returns.  If mount_nodev() fails for any reason whatsoever,
we proceed to
	functionfs_release_dev_callback(data.ffs_data);

That's broken in a lot of ways.  Suppose the thing has failed in
allocation of e.g. root inode or dentry.  We have
	functionfs_release_dev_callback(ffs);
	ffs_data_put(ffs);
done by ffs_fs_kill_sb() (ffs accessed via sb->s_fs_info), followed by
	functionfs_release_dev_callback(ffs);
from ffs_fs_mount() (via data.ffs_data).  Note that the second
functionfs_release_dev_callback() has every chance to be done to freed memory.

Suppose we fail *before* root inode allocation.  What happens then?
ffs_fs_kill_sb() doesn't do anything to ffs (it's either not called at all,
or it doesn't have a pointer to ffs stored in sb->s_fs_info).  And
	functionfs_release_dev_callback(data.ffs_data);
is called by ffs_fs_mount(), but here we are in nasal daemon country - we
are reading from a member of union we'd never stored into.  In practice,
we'll get what we used to store into the overlapping field, i.e. ffs_dev.
And then we get screwed, since we treat it (struct gfs_ffs_obj * in
disguise, returned by functionfs_acquire_dev_callback()) as struct
ffs_data *, pick what would've been ffs_data ->private_data from it
(*well* past the actual end of the struct gfs_ffs_obj - struct ffs_data
is much bigger) and poke in whatever it points to.

FWIW, there's a minor leak on top of all that in case if ffs_sb_fill()
fails on kstrdup() - ffs is obviously forgotten.

The thing is, there is no point in playing all those games with union.
Just allocate and initialize ffs_data *before* calling mount_nodev() and
pass a pointer to it via data.ffs_data.  And once it's stored in
sb->s_fs_info, clear data.ffs_data, so that ffs_fs_mount() knows that
it doesn't need to kill the sucker manually - from that point on
we'll have it done by ->kill_sb().
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: stable <stable@vger.kernel.org> # 3.3+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is not a bug on our side, but a misdesign in ITU T.416, yet with
all popular terminals supporting these codes, people consider this to
be a bug in Linux.  By breaking the design principles behind SGR codes
(gracefully ignoring unsupported ones should not require knowing about
them), 256 colour ones tend to turn blinking on before invoking an
arbitrary unrelated command.

This commit doesn't add such support, merely skips such codes without
ill effects.
Signed-off-by: NAdam Borowski <kilobyte@angband.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No modern terminal supports them, and SGR 38 conflicts with detecting
xterm-256 colours.  This also makes SGR 39 consistent with other popular
terminals.  Neither are used by ncurses' terminfo.
Signed-off-by: NAdam Borowski <kilobyte@angband.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The original version of this was done by Bastian Blank, who wrote:

> The problem is the following:
> - Architecture specific code sets preferred console to something bogus.
> - Command line handling tries to set preferred console but is overruled
>   by the old setting.
>
> The udbg0 console is a boot console and independant.

References: http://bugs.debian.org/492703Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that.

These calls were introduced in commit c08f0153 (serial: clps711x: Using
CPU clock subsystem for getting base UART speed).
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the missing uart_unregister_driver() before return
from sccnxp_probe() in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make Mode16 more preferred than Mode13, to match TRM baudrates table.
Signed-off-by: NAlexey Pelykh <alexey.pelykh@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix misnamed variable to eliminate confusion.
Signed-off-by: NAlexey Pelykh <alexey.pelykh@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In rx timeout ISR and tasklet, we don't issue new dma desc as rx_done ISR
will do that.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This resolves a warning where resource_size_t is larger than void *:

  drivers/tty/serial/imx.c:1542:6: warning: cast to pointer from integer
  	of different size [-Wint-to-pointer-cast]

Since iomem_base is a void *, casting to unsigned long is safe.

It's unclear to me that this comparison is truly needed, but it's there
on several other drivers as well.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Samsung serial driver currently does not support setting the
RTS pin with an ioctl(TIOCMSET) call. This patch adds this support.

Changes in v2:
 - Preserve the RTS pin's manual setting  in set_termios() also when
   enabling CRTSCTS.
Signed-off-by: NJosé Miguel Gonçalves <jose.goncalves@inov.pt>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The put_device(dev) at the bottom of the loop of device_shutdown
may result in the dev being cleaned up. In device_create_release,
the dev is kfreed.

However, device_shutdown attempts to use the dev pointer again after
put_device by referring to dev->parent.

Copy the parent pointer instead to avoid this condition.

This bug was found on Chromium OS's chromeos-3.8, which is based on v3.8.11.
See bug report : https://code.google.com/p/chromium/issues/detail?id=297842
This can easily be reproduced when shutting down with
hidraw devices that report battery condition.
Two examples are the HP Bluetooth Mouse X4000b and the Apple Magic Mouse.
For example, with the magic mouse :
The dev in question is "hidraw0"
dev->parent is "magicmouse"

In the course of the shutdown for this device, the input event cleanup calls
a put on hidraw0, decrementing its reference count.
When we finally get to put_device(dev) in device_shutdown, kobject_cleanup
is called and device_create_release does kfree(dev).
dev->parent is no longer valid, and we may crash in
put_device(dev->parent).

This change should be applied on any kernel with this change :
d1c6c030

Cc: stable@vger.kernel.org
Signed-off-by: NBenson Leung <bleung@chromium.org>
Reviewed-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NSonic Zhang <sonic.zhang@analog.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>