drv_priv->gmbus is an array. Comparing it with NULL is somewhat less useful
than a chocolate teapot.

Possibly we should be testing bus != NULL each iteration of the loop
instead ?

gcc could help by warning too!
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... flaky ddc hardware can cause a spurious NAK, resulting in the i2c
core and drm edid functions not trying to retry the edid transfer.

Luckily the gmbus quiescenting also times out for these cases, so we
can get out of this mess by returning -ETIMEDOUT for this specific
case. This way we keep the fast-fail of returning -ENXIO if there is
no device present, speeding up the boot process.

This regression has been introduced in

commit e646d577
Author: Daniel Kurtz <djkurtz@chromium.org>
Date:   Fri Mar 30 19:46:38 2012 +0800

    drm/i915/intel_i2c: always wait for IDLE before clearing NAK

v2: Return -ETIMEDOUT for this case and keep the -ENXIO for real NAKs,
suggested by Daniel Kurtz.

Cc: Daniel Kurtz <djkurtz@chromium.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49518Reported-and-Tested-by: NJulian Simioni <julian.simioni@gmail.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The hw just returns garbage.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49838Reported-and-tested-by: NVladyslav <DFEW.Entwickler@googlemail.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some of these messages can be hit when userspace tries to probe the i2c
with nothing connected or if the driver code tries to do the same.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48248Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A common method of probing an i2c bus is trying to do a zero-length read.
Handle this case by checking the length first waiting for data to be read.

This is actually important, since attempting a zero-length read is one
of the ways that i2cdetect and i2c_new_probed_device detect whether
there is device present on the bus with a given address.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48269Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The POSTING_READ() calls were originally added to make sure the writes
were flushed before any timing delays and across loops.
Now that the code has settled a bit, let's remove them.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Save the GMBUS2 value read while polling for state changes, and then
reuse this value when determining for which reason the loops were exited.
This is a small optimization which saves a couple of bus accesses for
memory mapped IO registers.

To avoid "assigning in if clause" checkpatch errors", use a ret variable
to store the wait_for macro return value.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It is very common for an i2c device to require a small 1 or 2 byte write
followed by a read.  For example, when reading from an i2c EEPROM it is
common to write and address, offset or index followed by a reading some
values.

The i915 gmbus controller provides a special "INDEX" cycle for performing
such a small write followed by a read.  The INDEX can be either one or two
bytes long.  The advantage of using such a cycle is that the CPU has
slightly less work to do once the read with INDEX cycle is started.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The i915 is only able to generate a STOP cycle (i.e. finalize an i2c
transaction) during a DATA or WAIT phase.  In other words, the
controller rejects a STOP requested as part of the first transaction in a
sequence.

Thus, for the first transaction we must always use a WAIT cycle, detect
when the device has finished (and is in a WAIT phase), and then either
start the next transaction, or, if there are no more transactions,
generate a STOP cycle.

Note: Theoretically, the last transaction of a multi-transaction sequence
could initiate a STOP cycle.  However, this slight optimization is left
for another patch.  We return -ETIMEDOUT if the hardware doesn't
deactivate after the STOP cycle.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
[danvet: added comment to the code that gmbus can't generate STOP on
the very first cycle.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GMBUS controller can report a NAK condition while a transaction is
still active. If the driver is fast enough, and the bus is slow enough,
the driver may clear the NAK condition while the controller is still
busy, resulting in a confused GMBUS controller.  This will leave the
controller in a bad state such that the next transaction may fail.

Also, return -ENXIO if a device NAKs a transaction.

Note: this patch also refactors gmbus_xfer to remove the "done" label.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GMBUS controller GMBUS3 register is double-buffered.  Take advantage
of this  by writing two 4-byte words before the first wait for HW_RDY.
This helps keep the GMBUS controller from becoming idle during long writes.

In fact, during experiments using the GMBUS interrupts, the HW_RDY
interrupt would only trigger for transactions >4 bytes after 2 writes
to GMBUS3.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A common method of probing an i2c bus is trying to do a zero-length write.
Handle this case by checking the length first before decrementing it.

This is actually important, since attempting a zero-length write is one
of the ways that i2cdetect and i2c_new_probed_device detect whether
there is device present on the bus with a given address.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit c3dfefa0.

gmbus in 3.4 has simply too many known issues:
- gmbus is too noisy, we need to rework the logging:
  https://bugs.freedesktop.org/show_bug.cgi?id=48248
- zero-length writes cause an OOPS, and they are
  userspace-triggerable:
  https://lkml.org/lkml/2012/3/30/176
- same for zero-length reads:
  https://bugs.freedesktop.org/show_bug.cgi?id=48269

We can try again for 3.5.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This memory is always allocated, and it is always a fixed size, so just
allocate it along with the rest of the driver state.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is no GMBUS "disabled" port 0, nor "reserved" port 7.
For the other 6 ports there is a fixed 1:1 mapping between pin pairs and
gmbus ports, which means every real gmbus port has a gpio pin.

Given these realizations, clean up gmbus initialization.

Tested on Sandybridge (gen 6, PCH == CougarPoint) hardware.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of letting other modules directly access the ->gmbus array,
introduce intel_gmbus_get_adapter() for looking up an i2c_adapter
for a given gmbus port identifier.  This will enable later refactoring
of the gmbus port list.

Note: Before requesting an adapter for a given gmbus port number, the
driver must first check its validity using i2c_intel_gmbus_is_port_valid().
If this check fails, a call to intel_gmbus_get_adapter() will WARN_ON and
return NULL.  This is relevant for parts of the driver that read a port
from VBIOS, which might be improperly initialized and contain an invalid
port.  In these cases, the driver must fall back to using a safer default
port.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of rolling our own custom quirk_xfer function, use the bit_algo
pre_xfer and post_xfer functions to setup and teardown bit-banged
i2c transactions.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to i915 documentation [1], "Port D" (DP/HDMI Port D) is
actually gmbus pin pair 6 (gmbus0.2:0 == 110b GPIOF), not 7 (111b).
Pin pair 7 is a reserved pair.

[1] Documentation for [DevSNB+] and [DevIBX], as found on
http://intellinuxgraphics.org:

[DevSNB+]:
http://intellinuxgraphics.org/documentation/SNB/IHD_OS_Vol3_Part3.pdf
 Section 2.2.2 lists the 6 gmbus ports (gpio pin pairs):
    [ 5: HDMI/DPD, 4: HDMIB, 3: HDMI/DPC, 2: LVDS, 1: SSC, 0: VGA ]
 2.2.2.1 lists the GPIO registers to control these 6 ports.
 2.2.3.1 lists the mapping between 5 of these gmbus ports and the 3
 Pin_Pair_Select bits (of the GMBUS0 register).  This table is missing
 HDMIB (port 101).

[DevIBX]: http://intellinuxgraphics.org/IHD_OS_Vol3_Part3r2.pdf
 Section 2.2.2 lists the same 6 gmbus ports plus two 'reserved' gpio
 ports.
 2.2.2.1 lists 8 GPIO registers... however, it says the size of the
 block is 6x32, which implies that those 2 reserved GPIO registers
 (GPIO_6 & GPIO_7) don't actually exist (or are irrelevant).
 2.2.3.1 lists the mapping between the 6 named gmbus ports and the 3
 Pin_Pair_Select bits (of the GMBUS0 register).  This table has HDMIB.

Note: the "reserved" and "disabled" pairs do not actually map to a
physical pair of pins, nor GPIO regs and shouldn't be initialized or used.
Fixing this is left for a later patch.

This bug had not been noticed earlier for two reasons:
 1) Until recently, "gmbus" mode was disabled - all transfers actually
    used "bit-bang" mode on GPIO port 5 (the "HDMI/DPD CTLDATA/CLK"
    pair), at register 0x5024 (defined as GPIOF i915_reg.h).
    Since this is the correct pair of pins for HDMI1, transfers succeed.

 2) Even if gmbus mode is re-enabled, the first attempted transaction
    will fail because it tries to use the wrong ("Reserved") pin pair.
    However, the driver immediately falls back again to the bit-bang
    method, which correctly uses GPIOF, so again, transfers succeed.

However, if gmbus mode is re-enabled and the GPIO fall-back mode is
disabled, then reading an attached monitor's EDID fail.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split out gmbus_xfer_read/write() helper functions.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the recent set of gmbus fixes, this seems to work on my i855gm.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Again, Valleyview modes these around, so make the mmio base more
explicit to consolidate the base address computations to one
HAS_PCH_SPLIT check.

v2: Fix up the PCH_SPLIT braino ... it actually works that way round.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the rework to merge the bit-banging fallback into the gmbus
i2c adapter we've gotten rid of the deadlock possibility that
originally lead to the disabling of this code.

This reverts the revert

commit 826c7e41
Author: Jean Delvare <khali@linux-fr.org>
Date:   Sat Jun 4 19:34:56 2011 +0000

    Revert "drm/i915: Enable GMBUS for post-gen2 chipsets"

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35572Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way we can simplify the setup and teardown a bit.

Because we don't actually allocate anything anymore for the force_bit
case, we can now convert that into a boolean.

Also and the functionality supported by the bit-banging together with
what gmbus can do, so that this doesn't randomly change any more.

v2: Chris Wilson noticed that I've mixed up && and & ...

v3: Clarify an if block as suggested by Eugeni Dodonov.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... and directly call the newly exported i2c bit-banging functions.

The code is still pretty convoluted because we only set up the gpio
i2c stuff when actually falling back, resulting in more complexity
than necessary. This will be fixed up in the next patch.

v2: Use exported i2c_bit_algo vtable instead of exported functions.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we set up the gpio fallback, we always have a 1:1 relationship
with an intel_gmbus. Exploit that to store all gpio related data in
there, too. This is a preparation step to merge the tw i2c adapters
controlling the same bus into one.

Just mundane code-munging in this patch.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way we can free up the bus->adaptor.algo_data pointer and make it
available for use with the bitbanging fallback algo.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

gmbus_xfer with a single message (particularly a single message write) would
set Bus Cycle Select to 100b, the Gen Stop cycle, instead of 101b,
No Index, Stop cycle. This would not start single message i2c transactions.

Also, gmbus_xfer done: will disable the interface without checking if
it is idle. In the case of writes, there will be no wait on status or delay
to ensure the write starts and completes before the interface is turned off.

Fixed the former issue by using the same cycle selection as used in the
I2C_M_RD for the write case.
GMBUS_CYCLE_WAIT | (i + 1 == num ? GMBUS_CYCLE_STOP : 0)
Fixed the latter by waiting on GMBUS_ACTIVE to deassert before disable.

Note from the grumpy d-i-n maintainer: The first hunk that changes the
gmbus read path is just cosmetics to align the code with the write
path.  I.e. the commit message above is slightly lying because the
first issue is _only_ with writes (and not simply "particularly").
Signed-off-by: NBenson Leung <bleung@chromium.org>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GMBUS has several ports and each has it's own corresponding
I2C adpater. When multiple I2C adapters call gmbus_xfer() at
the same time there is a race condition in using the underlying
GMBUS controller. Fixing this by adding a mutex lock when calling
gmbus_xfer().

v2: Moved gmbus_mutex below intel_gmbus and added comments.
Rebased to drm-intel-next-queued.
Signed-off-by: NYufeng Shen <miletus@chromium.org>
[danvet: Shortened the gmbus_mutex comment a bit and add the patch
revision comment to the commit message.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

A udelay value of 20 leads to an I2C bus running at only 25 kbps. I2C
devices can typically operate faster than this, 50 kbps should be fine
for all devices (and compliant devices can always stretch the clock if
needed.)

FWIW, the vast majority of framebuffer drivers set udelay to 10
already. So set it to 10 in DRM drivers too, this will make EDID block
reads faster. We might even lower the udelay value later if no problem
is reported.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Cc: Keith Packard <keithp@keithp.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

They need this to get all the EXPORT_SYMBOL variants and THIS_MODULE
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Signed-off-by: NAdam Jackson <ajax@redhat.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Revert commit 8f9a3f9b. This fixes a
hang when loading the eeprom driver (see bug #35572.) GMBUS will be
re-enabled later, differently.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Reported-by: NMarek Otahal <markotahal@gmail.com>
Tested-by: NYermandu Patapitafious <yermandu.dev@gmail.com>
Tested-by: NAndrew Lutomirski <luto@mit.edu>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Once a NAK has been asserted by the slave, we need to reset the GMBUS
controller in order to continue. This is done by asserting the Software
Clear Interrupt bit and then clearing it again to restore operations.

If we don't clear the NAK, then all future GMBUS xfers will fail,
including DDC probes and EDID retrieval.

v2: Add some comments as suggested by Keith Packard.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35781Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Tested-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: N"Mengmeng Meng" <mengmeng.meng@intel.com>

With the recent SDVO fix, this is working on all the machines I have to
hand - except for an 845G.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Fix many small bugs in I2C adapter registration:
* Properly reject unsupported GPIO pin.
* Fix improper use of I2C_NAME_SIZE (which is the size of
  i2c_client.name, not i2c_adapter.name.)
* Prefix adapter names with "i915" so that the user knows what the
  I2C channel is connected to.
* Fix swapped characters in the string used to name the GPIO-based
  adapter.
* Add missing comma in gmbus name table.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

As we use POSTING_READ to flush the write to the register before
proceeding, we do not care what the return value is and similar we do
not care for the read to be recorded whilst tracing register
read/writes.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

These registers are written very frequently, are timing sensitive, and
not particularly relevant to any debugging, so remove the tracepoints
from these.
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

In i2c GPIO fallback, index 6 is reserved for nothing.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>