When the tuner is attached, the tda10046 is not initilized yet, so it
is searching for its firmware. If the tuner is attached to the tda10046
silent i2c port, a bus collision can occur. Now the version is probed
during the first init or sleep call.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Set tda8290 to analog mode after init, otherwise the tuner driver will 
not accept i.e. the standby command.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch causes the bttv driver to automatically load the dvb-bt8xx module
for bttv/dvb hybrid cards. Successfully tested with a pcHDTV HD-2000 card.
This patch is based on the recent patches to enable autoloading of cx88-dvb,
cx88-blackbird and saa7134-dvb.
Signed-off-by: NJarod Wilson <jwilson@redhat.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix audio input source for capturing(playing) audio on AverTv Go 007 cards.
Signed-off-by: NDamian Minkov <damencho@damencho.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx88_print_irqbits were expecting a string pointer with 32 bytes. Better 
to pass the string size and use ARRAY_SIZE on its calls.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ATI HDTV Wonder needs to initialize some registers before allowing the
tuner to start working.
The current logic have lots of magic. This patch makes the code cleaner,
using ARRAY_SIZE() for the initialization array and using a
bidimensional array, instead of doing some stuff like:
	&buffer[i+2]
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

there were several "magic" for loops, addressing gpiomux array size (4).
Adrian Bunk showed that one of the loops were wrong, going from 0 to 4.

This patch provides the right fix for this trouble, by using ARRAY_SIZE
on all places where we have a for loop using gpiomux.

Thanks to: Adrian Bunk <bunk@stusta.de> for pointing me about this trouble.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

@ Don't assume that SOF headers can't cross packets boundaries
@ Fix compression quality selection
+ Add support for MI-0360 image sensor
* Documentation updates
@ Fix sysfs
@ MI0343 rewritten
* HV7131R color fixes and add new ABLC control
* Rename the archive from "sn9c102" to "sn9c1xx"
* fix typos
* better support for TAS5110D
@ fix OV7630 wrong colors
@ Don't return an error if no input buffers are enqueued yet on VIDIOC_STREAMON
* Add informations about colorspaces
* More appropriate error codes in case of failure of some system calls
* More precise hardware detection
* Add more informations about supported hardware in the documentation
+ More supported devices
+ Add support for HV7131R image sensor
Signed-off-by: NLuca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

After looking at a section bug (in the non-modular case, clearly 
non-init code referenced the __initdata parport_nr[]), I thought it was 
time to convert this driver to module_{init,exit}.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add raw bayer support to the ov7670 driver
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix up Cafe/ov7670 copyrights and maintainer entries
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't mirror ov7670 images by default.

The ov7670 sensor driver sets the mirror bit by default, which is not
the desired mode.  OLPC has been running with this patch for a while.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add suspend/resume support to the Cafe CCIC driver.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix up unsociable Cafe CCIC delays.

The Cafe CCIC driver contains some lengthy delays, some of which are 
unnecessary and some of which are done under lock.  Some were marked
with comments, but the comments somehow failed to make the issue go
away.  So fix it for real.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove an obsolete PCI ID.

The CAFE driver includes three PCI IDs, one of which corresponds to 
a development board which is no longer in use.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Set the PCI dev in the V4L2 dev so that the proper sysfs link gets made
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Logitech ViewPort AV 100 has the same internals as Cisco VT Camera. 
Fixing Pwc driver to handle it properly. 
Also, fixed the comments for both cameras.
Thanks to Martin Rubli for pointing me this.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I have a Cisco VT Camera, and it was just collecting dust.  I decided to
try connecting it to my Linux box at home.

Just a disgression about the product.  The Cisco VT Camera is a webcam
Cisco sold to work with their IP phone hardware and software.  It's mostly
useless on Windows, as it interfaces only to Cisco software.  You can find
some for cheap on eBay...

Physically, it's just a Logitech Pro 4000.  The only difference with the
Pro 4000 is the Cisco logo and that it's grey like the Pro 3000.  I believe
Cisco is now selling the Cisco VT Camera II, which look to be something
else...

So, assuming that it was a Pro 4000 inside, I created the little patch
attached.

I'm new to webcam under Linux, but I managed to get an image from it using
xawtv, and the image looked all right, so I consider that a success.  The
imaged seemed a bit small and I could not get the microphone driver loaded,
but I assume it's my lack of experience.  Note that I did not try any other
type_id, but this one works great.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The attach code for HAUPPAUGE_HVR3000 and HAUPPAUGE_HVR1300 is exactly
the same as the code used by HAUPPAUGE_HVR1100, HAUPPAUGE_HVR1100LP, and
WINFAST_DTV2000H.  So, those first two cards are added to the case block
used by the last three.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The new name fits to what it is and what is on the box.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are 2 new entries for p7131 boards and one correction for a board
with LNA.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Static locals should not be changed - the original contents gets lost.
Thanks to Trent Piepho for pointing me to this.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Besides power saving, this puts the AGC output of the tda8290
to tristate. This is necessary for some hybrid boards which
don't use a multiplexer for the AGC
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Modifies automatic mode selection for yuv playback. Behaviour is now that
source video with a vertical resolution below that of the currently set
broadcast mode will be treated as progressive. Video with a vertical
resolution greater or equal to the current broadcast mode (up to 576 lines)
will be treated as interlaced.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The TV standard should be set AFTER the TV output is fully initialized.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some of the new tuner entries may need to be mapped to compatible
tuners already defined. I don't know for certain which tuners
are compatible between manufacturers.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

replace leading spaces with tabs
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The ADS Tech InstantTV DVB-S is a clone of the KWorld DVB-S 100.
This patch adds autodetection support for this card based on
pci subsystem id.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Once the devices have been registered anyone can start changing the inputs or
TV standard before they have been initialized by the driver. This leads to
cases were the input is changed in an udev rule, but after that rule is
triggered the tail-end of the ivtv driver initialization can override
that by selecting the tuner input.
The correct sequence is to first setup the input, initial frequency and TV
standard before finally registering the video devices. This prevents any
udev rules from being triggered prematurely.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ivtv_remove which is called by pci_unregister_driver was still using
memory that was already freed. Ouch.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

VIDIOC_TRY_ENCODER_CMD did the same as VIDIOC_ENCODER_CMD, now it no longer
touches the encoder.
Both the encoder and decoder commands did not clear the flags field of unknown
flags.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Using v4l_printk_ioctl saves a lot of code duplication. Also moved a few
ioctl cases to another function, improving the ioctl grouping.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It is not immediately obvious why the ivtv symbols are exported
in ivtv-driver.c since both ivtv-fb and the IR-blaster module
are still out-of-tree, currently being ported to be in kernel.

Added a comment so people are aware of these issues.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Every file should include the headers containing the prototypes
for its global functions.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>