Some of the trap code was still assuming that alternate
global %g6 was hard coded with current_thread_info().
Let's just consistently flush at KERNBASE when we need
a pipeline synchronization.  That's locked into the TLB
and will always work.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

UltraSPARC has special sets of global registers which are switched to
for certain trap types.  There is one set for MMU related traps, one
set of Interrupt Vector processing, and another set (called the
Alternate globals) for all other trap types.

For what seems like forever we've hard coded the values in some of
these trap registers.  Some examples include:

1) Interrupt Vector global %g6 holds current processors interrupt
   work struct where received interrupts are managed for IRQ handler
   dispatch.

2) MMU global %g7 holds the base of the page tables of the currently
   active address space.

3) Alternate global %g6 held the current_thread_info() value.

Such hardcoding has resulted in some serious issues in many areas.
There are some code sequences where having another register available
would help clean up the implementation.  Taking traps such as
cross-calls from the OBP firmware requires some trick code sequences
wherein we have to save away and restore all of the special sets of
global registers when we enter/exit OBP.

We were also using the IMMU TSB register on SMP to hold the per-cpu
area base address, which doesn't work any longer now that we actually
use the TSB facility of the cpu.

The implementation is pretty straight forward.  One tricky bit is
getting the current processor ID as that is different on different cpu
variants.  We use a stub with a fancy calling convention which we
patch at boot time.  The calling convention is that the stub is
branched to and the (PC - 4) to return to is in register %g1.  The cpu
number is left in %g6.  This stub can be invoked by using the
__GET_CPUID macro.

We use an array of per-cpu trap state to store the current thread and
physical address of the current address space's page tables.  The
TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this
table, it uses __GET_CPUID and also clobbers %g1.

TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load
the current processor's IRQ software state into %g6.  It also uses
__GET_CPUID and clobbers %g1.

Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the
current address space's page tables into %g7, it clobbers %g1 and uses
__GET_CPUID.

Many refinements are possible, as well as some tuning, with this stuff
in place.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now use the TSB hardware assist features of the UltraSPARC
MMUs.

SMP is currently knowingly broken, we need to find another place
to store the per-cpu base pointers.  We hid them away in the TSB
base register, and that obviously will not work any more :-)

Another known broken case is non-8KB base page size.

Also noticed that flush_tlb_all() is not referenced anywhere, only
the internal __flush_tlb_all() (local cpu only) is used by the
sparc64 port, so we can get rid of flush_tlb_all().

The kernel gets it's own 8KB TSB (swapper_tsb) and each address space
gets it's own private 8K TSB.  Later we can add code to dynamically
increase the size of per-process TSB as the RSS grows.  An 8KB TSB is
good enough for up to about a 4MB RSS, after which the TSB starts to
incur many capacity and conflict misses.

We even accumulate OBP translations into the kernel TSB.

Another area for refinement is large page size support.  We could use
a secondary address space TSB to handle those.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of code patching to handle the page size fields in
the context registers, just use variables from which we get
the proper values.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current uncorrectable error handling was poor enough
that the processor could just loop taking the same
trap over and over again.  Fix things up so that we
at least get a log message and perhaps even some register
state.

In the process, much consolidation became possible,
particularly with the correctable error handler.

Prefix assembler and C function names with "spitfire"
to indicate that these are for Ultra-I/II/IIi/IIe only.

More work is needed to make these routines robust and
featureful to the level of the Ultra-III error handlers.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!