After 57a38eff (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb1 interface refuses to work properly because it tries
to cling to address 0 which isn't able to communicate in broadcast with
the mac anymore. The micrel phy on the board is actually configured
to show up at address 1.
Adding the phy node and its real address fixes the issue.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: <stable@vger.kernel.org> #3.19
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung 2nd fixes for v4.0" from Kukjin Kim:

- Fix build breakage exynos cpuidle driver on !SMP
  because it is coupled built-in so added check for SMP.

- Fix lid, power pin-functions and mmc node updates
  for exynos5250-spring: Fixes commit ID 53dd4138
  ("ARM: dts: Add exynos5250-spring device tree")

* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Fix build breakage cpuidle on !SMP
  ARM: dts: fix lid and power pin-functions for exynos5250-spring
  ARM: dts: fix mmc node updates for exynos5250-spring
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge "ARM: mvebu: fixes for v4.0" from Gregory Clement:

mvebu fix for 4.0

Disable CPU Idle on Armada 38x

* tag 'mvebu-fixes-4.0' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Disable CPU Idle on Armada 38x
Signed-off-by: NOlof Johansson <olof@lixom.net>

When building specific DTBs out of the kernel tree the vendor subdirs
(boot/dts/<vendor>) are not created, ensure that they are before
building the DTB.
Signed-off-by: NNathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On Armada 38x SoCs, under heavy I/O load, the system hangs when CPU
Idle is enabled. Waiting for a solution to this issue, this patch
disables the CPU Idle support for this SoC.

As CPU Hot plug support also uses some of the CPU Idle functions it is
also affected by the same issue. This patch disables it also for the
Armada 38x SoCs.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.17 +

Merge tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Allwinner fixes for 4.0

There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.

* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
  ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
  ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for the -rc cycle:

- Fix a device tree based booting vs legacy booting regression for
  omap3 crypto hardware by adding the missing DMA channels.

- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.

- Fix two timer issues that can cause hangs if the timer related
  hwmod data is missing like it often initially is for new SoCs.

- Remove pcie hwmods entry from dts as that causes runtime PM to
  fail for the PHYs.

- A paper bag type dts configuration fix for dm816x GPIO
  interrupts that I just noticed. This is most of the changes
  diffstat wise, but as it's a basic feature for connecting
  devices and things work otherwise, it should be fixed.

* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: dra7: remove ti,hwmod property from pcie phy
  ARM: OMAP: dmtimer: disable pm runtime on remove
  ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
  ARM: OMAP2+: Fix socbus family info for AM33xx devices
  ARM: dts: omap3: Add missing dmas for crypto
Signed-off-by: NOlof Johansson <olof@lixom.net>

Late fix for v4.0 on the SoCFPGA platform:
- Fix interrupt number for SPI1 interface

* tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next:
  ARM: socfpga: dts: fix spi1 interrupt
Signed-off-by: NOlof Johansson <olof@lixom.net>

The UART reference clock speed is 7273.8 kHz, not 72738 kHz.

Dots aren't usually used in node names even though ePAPR permits
them.  However, this can easily be avoided by expressing the
frequency in Hz, not kHz.

This patch changes the name to refclk7273800hz, reflecting the
actual clock speed.
Signed-off-by: NDave Martin <Dave.Martin@arm.com>
Acked-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

arm: pxa: fixes for v4.0-rc5

There are only 2 fixes, one for the zeus board about the regulator changes,
where a typo prevented the zeus board from having a working can regulator,
and one regression triggered by the interrupts IRQ shift of 16 affecting all
boards.

* tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux:
  ARM: pxa: fix pxa interrupts handling in DT
  ARM: pxa: Fix typo in zeus.c
Signed-off-by: NOlof Johansson <olof@lixom.net>

Without proper regulator support for individual boards, it is dangerous
to have overclocked/overvoltaged OPPs in the list. Cpufreq will increase
the frequency without the accompanying voltage increase, resulting in
an unstable system.

Remove them for now. We can revisit them with the new version of OPP
bindings, which support boost settings and frequency ranges, among
other things.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Olimex A10-Lime is known to be unstable when running at 1008MHz.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The socfpga.dtsi currently has the wrong interrupt number set for SPI master 1
Trying to use the master without this change results in the kernel boot
process waiting forever for an interrupt that will never occur while
attempting to probe any slave devices configured in the device tree as being
under SPI master 1.

The change works for the Cyclone V, and according to the Arria 5 handbook
should be good there too.
Signed-off-by: NMark James <maj@jamers.net>
Acked-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

Commit 7800064b ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.

This turned out several issues that need to be fixed:

- I set the GPIO type wrong to be compatible with omap3 instead
  of omap4. The GPIO controller on dm816x has EOI interrupt
  register like omap4 and am335x.

- I got the GPIO interrupt numbers wrong as each bank has two
  and we only use one. They need to be set up the same way as
  on am335x.

- The gpio banks are missing interrupt controller related
  properties.

With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.

For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that we don't have hwmod entry for pcie PHY remove the
ti,hwmod property from PCIE PHY's. Otherwise we will get:

platform 4a094000.pciephy: Cannot lookup hwmod 'pcie1-phy'
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Exynos cpuidle driver has coupled cpuidle built-in so it cannot be
built without SMP:

arch/arm/mach-exynos/pm.c: In function 'exynos_cpu0_enter_aftr':
arch/arm/mach-exynos/pm.c:246:4: error: implicit declaration of function 'arch_send_wakeup_ipi_mask' [-Werror=implicit-function-declaration]
arch/arm/mach-exynos/built-in.o: In function 'exynos_pre_enter_aftr':
../arch/arm/mach-exynos/pm.c:300: undefined reference to 'cpu_boot_reg_base'
arch/arm/mach-exynos/built-in.o: In function 'exynos_cpu1_powerdown':
../arch/arm/mach-exynos/pm.c:282: undefined reference to 'exynos_cpu_power_down'

Fix it by adding missing checks for SMP.
Reported-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Disable the pm_runtime of the device upon remove. This is
added to balance the pm_runtime_enable() invoked in the probe.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The current OMAP dmtimer probe does not check for the return
status of pm_runtime_get_sync() before initializing the timer
registers. Any timer with missing hwmod data would return a
failure here, and the access of registers without enabling the
clocks for the timer would trigger a l3_noc interrupt and a
kernel boot hang. Add proper checking so that the probe would
return a failure graciously without hanging the kernel boot.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Configure the pins in external interrupt mode, as done for Snow in
e5e5c6d1 ("ARM: dts: Add power and lid GPIO keys pinctrl for
exynos5250-snow").
Reported-by: NKukjin Kim <kgene@kernel.org>
Suggested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Fixes: 53dd4138 ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Resolve a merge conflict with mmc refactoring aaa25a5a ("ARM: dts:
unuse the slot-node and deprecate the supports-highspeed for dw-mmc in
exynos") by dropping the slot@0 nodes, moving its bus-width property to
the mmc node and replacing supports-highspeed with cap-{mmc,sd}-highspeed,
matching exynos5250-snow.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: 53dd4138 ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: NAndreas Faerber <afaerber@suse.de>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: <stable@vger.kernel.org>        [3.19+]
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The family information in the soc-bus data is currently
not classified properly for AM33xx devices, and a read
of /sys/bus/soc/devices/soc0/family currently shows
"Unknown". Fix the same.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds missing dma DTS definitions for omap aes and sham drivers.
Without it kernel drivers do not work for device tree based booting
while it works for legacy booting on general purpose SoCs.

Note that further changes are still needed for high secure SoCs. But since
that never worked in legacy boot mode either, those will be sent separately.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Acked-by: NPavel  Machek <pavel@ucw.cz>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Pull "ARM: rockchip: small fixes for 4.0-rc" from Heiko Stuebner:

Adding a default-disabled state to the new gmac node and an
update to the MAINTAINERS entry adding a rockchip regexp entry.

* tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
  MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry

Pull drm fix from Dave Airlie:
 "An oops snuck in in an -rc3 patch, this fixes it"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  [PATCH] drm/mm: Fix support 4 GiB and larger ranges

Pull clock framework fixes from Michael Turquette:
 "The clk fixes for 4.0-rc4 comprise three themes.

  First are the usual driver fixes for new regressions since v3.19.

  Second are fixes to the common clock divider type caused by recent
  changes to how we round clock rates.  This affects many clock drivers
  that use this common code.

  Finally there are fixes for drivers that improperly compared struct
  clk pointers (drivers must not deref these pointers).  While some of
  these drivers have done this for a long time, this did not cause a
  problem until we started generating unique struct clk pointers for
  every consumer.  A new function, clk_is_match was introduced to get
  these drivers working again and they are fixed up to no longer deref
  the pointers themselves"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  ASoC: kirkwood: fix struct clk pointer comparing
  ASoC: fsl_spdif: fix struct clk pointer comparing
  ARM: imx: fix struct clk pointer comparing
  clk: introduce clk_is_match
  clk: don't export static symbol
  clk: divider: fix calculation of initial best divider when rounding to closest
  clk: divider: fix selection of divider when rounding to closest
  clk: divider: fix calculation of maximal parent rate for a given divider
  clk: divider: return real rate instead of divider value
  clk: qcom: fix platform_no_drv_owner.cocci warnings
  clk: qcom: fix platform_no_drv_owner.cocci warnings
  clk: qcom: Add PLL4 vote clock
  clk: qcom: lcc-msm8960: Fix PLL rate detection
  clk: qcom: Fix slimbus n and m val offsets
  clk: ti: Fix FAPLL parent enable bit handling

bad argument if(tmp)... in check_free_hole

fix oops: kernel BUG at drivers/gpu/drm/drm_mm.c:305!

[airlied: excellent, this was my task for today].
Signed-off-by: NKrzysztof Kolasa <kkolasa@winsoft.pl>
Reviewed-by: NChris wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a rather unpleasantly large set of bug fixes for arm-soc, Most
  of them because of cross-tree dependencies for Exynos where we should
  have figured out the right path to merge things before the merge
  window, and then the maintainer being unable to sort things out in
  time during a business trip.

  The other changes contained here are the usual collection:

  MAINTAINERS file updates
   - Gregory Clement is now a co-maintainer for the legacy Marvell EBU
     platforms
   - A MAINTAINERS entry for the Freescale Vybrid platform that was
     added last year
   - Matt Porter no longer works as a maintainer on Broadcom SoCs

  Build-time issues
   - A compile-time error for at91
   - Several minor DT fixes on at91, imx, exynos, socfpga, and omap
   - The new digicolor platform was not correctly enabled at all

  Configuration issues
   - Two defconfig fix for regressions using USB on versatile express
     and on OMAP3
   - Enabling all 8 CPUs on Allwinner/SUNxi
   - Enabling the new STiH410 platform to be usable

  Bug fixes in platform code
   - A missing barrier for socfpga
   - Fixing LPDDR1 self-refresh mode on at91
   - Fixing RTC interrupt numbers on Exynos3250
   - Fixing a cache-coherency issues in CPU power-down on Exynos5
   - Multiple small OMAP power management fixes"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
  MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
  ARM: at91: pm_slowclock: fix the compilation error
  ARM: at91/dt: fix USB high-speed clock to select UTMI
  ARM: at91/dt: fix at91 udc compatible strings
  ARM: at91/dt: declare matrix node as a syscon device
  ARM: vexpress: update CONFIG_USB_ISP1760 option
  ARM: digicolor: add the machine directory to Makefile
  ARM: STi: Add STiH410 SoC support
  MAINTAINERS: add Freescale Vybrid SoC
  MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
  ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
  ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
  ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
  ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
  ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
  ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
  ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
  ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
  ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
  ARM: dts: OMAP5: fix polling intervals for thermal zones
  ...

Pull irqchip fixes from Jason Cooper:
 "armada-370-xp:
   - Chained per-cpu interrupts

  gic{,-v3,v3-its}"
   - Various fixes for safer operation"

* tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux:
  irqchip: gicv3-its: Support safe initialization
  irqchip: gicv3-its: Define macros for GITS_CTLR fields
  irqchip: gicv3-its: Add limitation to page order
  irqchip: gicv3-its: Use 64KB page as default granule
  irqchip: gicv3-its: Zero itt before handling to hardware
  irqchip: gic-v3: Fix out of bounds access to cpu_logical_map
  irqchip: gic: Fix unsafe locking reported by lockdep
  irqchip: gicv3-its: Fix unsafe locking reported by lockdep
  irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration
  irqchip: gicv3-its: Allocate enough memory for the full range of DeviceID
  irqchip: gicv3-its: Fix ITS CPU init
  irqchip: armada-370-xp: Fix chained per-cpu interrupts

Pull drm fixes from Dave Airlie:
 "Misc i915, vmwgfx and radeon fixes along with a fix for one of those
  recursive sleep mutex debug cases in the mst code"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix an issue with the device losing its irq line on module unload
  drm/vmwgfx: Correctly NULLify dma buffer pointer on failure
  drm/vmwgfx: Reorder device takedown somewhat
  drm/vmwgfx: Fix a couple of lock dependency violations
  drm/radeon: drop setting UPLL to sleep mode
  drm/radeon: fix wait to actually occur after the signaling callback
  drm/i915: Prevent TLB error on first execution on SNB
  drm/i915: Do both mt and gen6 style forcewake reset on ivb probe
  drm/i915: Make WAIT_IOCTL negative timeouts be indefinite again
  drm/i915: use in_interrupt() not in_irq() to check context
  drm/mst: fix recursive sleep warning on qlock
  drm: Don't assign fbs for universal cursor support to files

Pull SCSI fix from James Bottomley:
 "This is a simple fix for a domain revalidation crash which has
  recently turned up in the libsas code (applies to mvsas, isc and
  aic94xx)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  libsas: Fix Kernel Crash in smp_execute_task

This block should not be enabled by default or else if the kconfig is set,
it will try to load/probe even if there's no phy connected.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The regexp option is a nice way to catch even weirder paths like the current
drivers/gpu/drm/rockchip/* or others in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Pull file locking bugfix from Jeff Layton:
 "Just a small fix for a potential problem in one of the lease
  tracepoints"

* tag 'locks-v4.0-4' of git://git.samba.org/jlayton/linux:
  locks: fix generic_delete_lease tracepoint to use victim pointer

Pull VFIO fix from Alex Williamson:
 "Add missing break to avoid clobbering ioctl (Alexey Kardashevskiy)"

* tag 'vfio-v4.0-rc4' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Add missing break to enable VFIO_PCI_ERR_IRQ_INDEX

Pull arm64 fixes from Catalin Marinas:

 - add TLB invalidation for page table tear-down which was missed when
   support for CONFIG_HAVE_RCU_TABLE_FREE was added (assuming page table
   freeing was always deferred)

 - use UEFI for system and reset poweroff if available

 - fix asm label placement in relation to the alignment statement

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: put __boot_cpu_mode label after alignment instead of before
  efi/arm64: use UEFI for system reset and poweroff
  arm64: Invalidate the TLB corresponding to intermediate page table levels

Merge tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fix from Shuah Khan:
 "selftests/exec: Check if the syscall exists and bail if not"

* tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/exec: Check if the syscall exists and bail if not

It's possible that "fl" won't point at a valid lock at this point, so
use "victim" instead which is either a valid lock or NULL.
Signed-off-by: NJeff Layton <jeff.layton@primarydata.com>

Another one for the big head.S spring cleaning: the label should
be after the .align or it may point to the padding.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>