For systems which do not have a jack detection feature allow some debounce
to be specified before we perform accessory identification, improving
robustness without impacting button detection responsiveness.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some systems use the audio CODEC to clock a DAI with multiple data lines
in parallel, meaning that bit clocks are only required for a smaller number
of channels than data is sent for. In some cases providing the extra bit
clocks can take the other devices on the audio bus out of spec.

Support such systems by allowing a maximum number of channels to be
specified.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This can be used to provide some additional settling time to ensure that
we don't start microphone detection while the microphone pin is connected
to one of the headphone pins.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes the analogue circuitry connected to the microphone needs some
time to settle after power up. Allow systems to configure this delay in
the platform data, the driver will then insert the required delay during
power up of paths that involve the microphone.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NChris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

It's causing confusion with the regulator level field of the same name
and serves no useful function.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>

Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>

Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In systems where the LDO enables are always driven (for example, being
connected to an always on supply rail or a GPIO which is driven by the
CPU even in suspend) then we can disable the pull downs on the LDO for
a small power savings.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This needs to be an out of band value for the register and on this device
registers are 16 bit so we must shift left one to the 17th bit.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

DSP2 in the WM8958 can be used to support an upgraded EQ for use in
demanding applications.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

With appropriate firmware the WM8958 can support Virtual Surround Sound or
VSS, widening the stereo audio image for improved user experience. Enable
support for this mode of operation when the appropriate firmware can be
loaded at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NUk Kim <w0806.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8994 has an interrupt controller which supports interrupts for
both CODEC and GPIO portions of the chip. Support this using genirq,
while allowing for systems that do not have an interrupt hooked up.

Wrapper functions are provided for the IRQ request and free to simplify
the code in consumer drivers when handling cases where IRQs are not
set up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>

The WM8994 is a highly integrated ultra low power audio hub CODEC.
Since it includes on-board regulators and GPIOs it is represented
as a multi-function device, though the overwhelming majority of
the functionality is provided by the ASoC CODEC driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>