The "irq_handler" name is already defined there on a header
file:

/devel/v4l/temp/drivers/staging/media/lirc/lirc_parallel.c:223:13: error: conflicting types for ‘irq_handler’
 static void irq_handler(void *blah)
             ^
In file included from /devel/v4l/temp/arch/mn10300/include/asm/reset-regs.h:16:0,
                 from /devel/v4l/temp/arch/mn10300/include/asm/irq.h:18,
                 from /devel/v4l/temp/include/linux/irq.h:24,
                 from /devel/v4l/temp/arch/mn10300/include/asm/hardirq.h:16,
                 from /devel/v4l/temp/include/linux/preempt_mask.h:5,
                 from /devel/v4l/temp/include/linux/sched.h:25,
                 from /devel/v4l/temp/include/linux/utsname.h:5,
                 from /devel/v4l/temp/arch/mn10300/include/asm/elf.h:15,
                 from /devel/v4l/temp/include/linux/elf.h:4,
                 from /devel/v4l/temp/include/linux/module.h:14,
                 from /devel/v4l/temp/drivers/staging/media/lirc/lirc_parallel.c:29:
/devel/v4l/temp/arch/mn10300/include/asm/exceptions.h:107:24: note: previous declaration of ‘irq_handler’ was here
 extern asmlinkage void irq_handler(void);

/devel/v4l/patchwork/drivers/staging/media/lirc/lirc_serial.c:653:20: error: conflicting types for ‘irq_handler’
 static irqreturn_t irq_handler(int i, void *blah)
                    ^
In file included from /devel/v4l/patchwork/arch/mn10300/include/asm/reset-regs.h:16:0,
                 from /devel/v4l/patchwork/arch/mn10300/include/asm/irq.h:18,
                 from /devel/v4l/patchwork/include/linux/irq.h:24,
                 from /devel/v4l/patchwork/arch/mn10300/include/asm/hardirq.h:16,
                 from /devel/v4l/patchwork/include/linux/preempt_mask.h:5,
                 from /devel/v4l/patchwork/include/linux/sched.h:25,
                 from /devel/v4l/patchwork/include/linux/utsname.h:5,
                 from /devel/v4l/patchwork/arch/mn10300/include/asm/elf.h:15,
                 from /devel/v4l/patchwork/include/linux/elf.h:4,
                 from /devel/v4l/patchwork/include/linux/module.h:14,
                 from /devel/v4l/patchwork/drivers/staging/media/lirc/lirc_serial.c:53:
/devel/v4l/patchwork/arch/mn10300/include/asm/exceptions.h:107:24: note: previous declaration of ‘irq_handler’ was here
 extern asmlinkage void irq_handler(void);

So, rename it, to avoid namespace conflicts.

This patch fixes building media drivers with allyesconfig/almodconfig on
mn10300 arch.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fixes those warnings:
	drivers/staging/media/go7007/go7007-usb.c: In function 'go7007_usb_probe':
	drivers/staging/media/go7007/go7007-usb.c:1060: warning: 'go' is used uninitialized in this function

While here, comment a code that will never run.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

	drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_get_time_us':
	drivers/media/dvb-frontends/dib8000.c:3957: warning: 'interleaving' may be used uninitialized in this function
	drivers/media/dvb-frontends/dib8000.c:3956: warning: 'rate_denum' may be used uninitialized in this function

Those are actually false positives, but it doesn't hurt cleaning them.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When compiling with avr32, it gets those errors:

	drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_get_stats':
	drivers/media/dvb-frontends/dib8000.c:4121: warning: integer constant is too large for 'long' type

Fix integer representation to avoid overflow.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This function isn't used nowhere outside the same .c file.
Fixes this warning:

drivers/media/radio/si4713/radio-usb-si4713.c:418:5: warning: no previous prototype for 'si4713_register_i2c_adapter' [-Wmissing-prototypes]
 int si4713_register_i2c_adapter(struct si4713_usb_device *radio)
     ^

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix two warns below, by commenting the unused code:

drivers/media/platform/sh_vou.c: In function 'sh_vou_configure_geometry':
drivers/media/platform/sh_vou.c:446:49: warning: variable 'height_max' set but not used [-Wunused-but-set-variable]
  unsigned int black_left, black_top, width_max, height_max,
                                                 ^
drivers/media/platform/sh_vou.c: In function 'sh_vou_isr':
drivers/media/platform/sh_vou.c:1056:13: warning: variable 'side' set but not used [-Wunused-but-set-variable]
  static int side;
             ^

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The video_type was never set correctly for PAL: it's not a bool, instead
it is a register value.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: tomdev@freenet.de
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Added command line parameter preallocate_big_buffers so that the digital
transfer buffers can be allocated when the driver is registered. They
do not have to be allocated every time a feed is started.
Signed-off-by: NTim Mester <tmester@ieee.org>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Free what was allocated if there is a failure allocating
transfer buffers.

Stop the feed on a start feed error.  The stop feed is not always called
if start feed fails.  If the feed is not stopped on error, then the driver
will be stuck so that it can never start feeding again.

[m.chehab@samsung.com: CodingStyle cleanup]
Signed-off-by: NTim Mester <tmester@ieee.org>
Acked-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add v4l2 controls to set desired profile for VP8 encoder.
Acceptable levels for VP8 encoder are
0: Version 0
1: Version 1
2: Version 2
3: Version 3
Signed-off-by: NKiran AVND <avnd.kiran@samsung.com>
Signed-off-by: NPawel Osciak <posciak@chromium.org>
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

s5p_mfc_get_node_type() relies on get_index() helper function, which in
turn relies on video_device index numbers assigned on driver
registration. All this code is not really needed, because there is
already access to respective video_device structures via common
s5p_mfc_dev structure. This fixes the issues introduced by patch
1056e438 ("v4l2-dev: Fix race condition
on __video_register_device"), which has been merged in v3.12-rc1.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Adds v4l2 controls to set MIN, MAX QP values and
I, P frame QP for vp8 encoder.
Signed-off-by: NKiran AVND <avnd.kiran@samsung.com>
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Now that em28xx can be compiled without V4L support, we should
call em28xx_setup_xc3028() on both em28xx-v4l and em28xx-dvb
modules.
Reported-by: NChris Lee <updatelee@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The buffer size on nxt200x is not enough:

	...
	> Dec 20 10:52:04 rich kernel: [   31.747949] nxt200x: nxt200x_writebytes: i2c wr reg=002c: len=255 is too big!
	...

Increase it to 256 bytes.
Reported-by: NRich Freeman <rich0@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If em28xx is disconnected, return -ENODEV to all PCM callbacks.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The URB calculus code may eventually be moved to some other
place, like at pcm open, if it ends by needing more setups, like
working with different bit rates, or different audio latency.

So, move it into a separate routine. That also makes the code
more readable.

No functional changes.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Pulseaudio has the bad habit of stopping a streaming audio if
a device, opened in non-block mode, waits.

It is impossible to avoid em28xx to wait, as it will send commands
via I2C, and other I2C operations may be happening (firmware
transfers, Remote Controller polling, etc). Yet, as each em28xx
subdriver locks em28xx-dev to protect the access to the hardware,
it is possible to minimize the audio glitches by returning -EAGAIN
to pulseaudio, if the lock is already taken by another subdriver.
Reported-by: NAntti Palosaari <crope@iki.fi>
Tested-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If the period size is wrong, userspace will assume a wrong delay
any may negociate an inadequate value.

The em28xx devices use 8 for URB interval, in microframes,
and the driver programs it to have 64 packets.

That means that the IRQ sampling period is 125 * 8 * 64,
with is equal to 64 ms.

So, that's the minimal latency with the current settings. It is
possible to program a lower latency, by using less than 64 packets,
but that increases the amount of bandwitdh used, and the number of
IRQ events per second.

In any case, in order to support it, the driver logic should be
changed to fill those parameters in realtime.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The current code hardcodes the number of audio URBs, the number
of packets per URB and the maximum URB size.

This is not a good idea, as it:

- wastes more bandwidth than necessary, by using a very
  large number of packets;

- those constants are bound to an specific scenario, with
  a bandwidth of 48 kHz;

- don't take the maximum endpoint size into account;

- with urb->interval = 1 on xHCI, those constraints cause a "funny"
  setup: URBs with 64 packets inside, with only 24 bytes total. E. g.
  a complete waste of space.

Change the code to do dynamic URB audio calculus and allocation.

For now, use the same constraints as used before this patch, to
avoid regressions.

A good scenario (tested) seems to use those defines, instead:

	#define EM28XX_MAX_AUDIO_BUFS          8
	#define EM28XX_MIN_AUDIO_PACKETS       2

But let's not do such change here, letting the optimization to
happen on latter patches, after more tests.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

De-allocate memory and free sound if an error happens.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Just filling urb->interval with 1 is wrong, and causes a different
behaviour with xHCI.

With EHCI, the URB size is typically 192 bytes. However, as
xHCI specifies intervals in microframes, the URB size becomes
too short (24 bytes).

With this patch, the interval will be properly initialized, and
the device will behave the same if connected into a xHCI or an
EHCI device port.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

If i2c_debug is enabled, we splicitly want to know when a
device fails with timeout.

If i2c_debug==2, this is already provided, for each I2C transfer
that fails.

However, most of the time, we don't need to go that far. We just
want to know that I2C transfers fail.

So, add such errors for normal (ret == 0x10) I2C aborted timeouts.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The I2C output messages is too polluted. Clean it a little
bit, by:
	- use the proper core support for memory dumps;
	- hide most stuff under the i2c_debug umbrella;
	- add the missing KERN_CONT where needed;
	- use 2 levels or verbosity. Only the second one
	  will show the I2C transfer data.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Follow the error codes for I2C as described at Documentation/i2c/fault-codes.

In the case of the I2C status register (0x05), this is mapped into:

	- ENXIO - when reg 05 returns 0x10
	- ETIMEDOUT - when the device is not temporarily not responding
		      (e. g. reg 05 returning something not 0x10 or 0x00)
	- EIO - for generic I/O errors that don't fit into the above.

In the specific case of 0-byte reads, used only during I2C device
probing, it keeps returning -ENODEV.

TODO: return EBUSY when reg 05 returns 0x20 on em2874 and upper.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

In the lack of a better spec, let's assume the timeout
values compatible with SMBus spec:
	http://smbus.org/specs/smbus110.pdf

at chapter 8 - Electrical Characteristics of SMBus devices

Ok, SMBus is a subset of I2C, and not all devices will be
following it, but the timeout value before this patch was not
even following the spec.

So, while we don't have a better guess for it, use 35 + 1
ms as the timeout.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This macro is used by all em28xx devices, and not just em2800.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The I2C wait completion/timeout logic currently assumes that
msleep(5) will wait exaclty 5 ms. This is not true at all,
as it depends on CONFIG_HZ.

Convert it to use jiffies, in order to not wait for more time
than needed.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of assuming that msleep() is precise, use a jiffies
based code to wait for AC97 to be available.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That removes those timeout errors:

[ 3675.930940] xc2028 19-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
[ 3676.060487] xc2028 19-0061: divisor= 00 00 8d d0 (freq=567.250)
[ 3676.349449] xc2028 19-0061: Putting xc2028/3028 into poweroff mode.
[ 3698.247645] xc2028 19-0061: xc2028_get_reg 0002 called
[ 3698.253276] em2860 #0: I2C transfer timeout on writing to addr 0xc2
[ 3698.253301] xc2028 19-0061: i2c input error: rc = -121 (should be 2)
[ 3698.253327] xc2028 19-0061: xc2028_signal called
[ 3698.253339] xc2028 19-0061: xc2028_get_reg 0002 called
[ 3698.259283] em2860 #0: I2C transfer timeout on writing to addr 0xc2
[ 3698.259312] xc2028 19-0061: i2c input error: rc = -121 (should be 2)
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Only send a power down command for the device if it is not already
in power down state. That prevents a timeout when trying to talk
with the device.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of allocating/deallocating URBs and transfer buffers
every time stream is started/stopped, just do it once.

That reduces the memory allocation pressure and makes the
code that start/stop streaming a way simpler.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Instead of allocating transfer buffers with kmalloc() use
usb_alloc_coherent().

This patch should make it work also with ARM CPUs.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add a new USB ID to the driver.
Signed-off-by: NLinks (Markus) <help.markus+git@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The comment incorrectly explains that the code verifies information
provided by userspace, while verification has been performed earlier in
reality. Fix it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Value of fec is achieved by the upper nibble bits 6,7 & 8.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Register 0x70 is used to set fec, register 0x76 is used to get fec

Register 0x76 is set to 0x8.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The correct lock values is when bits of the value 0xee are set.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Current setting of symbol rate is not very actuate causing
loss of lock.

Covert temp to u64 and use mclk to calculate from big number.

Calculate symbol rate by dividing symbol rate by 1000 times
1 << 24 and dividing sum by mclk.

Add other symbol rate settings to function registers 0xa0-0xa3.

In set_frontend add changes to register 0xf1 this must be done
prior call to fe_reset. Register 0x00 doesn't need a second
write of 0x1

Applied after patch
m88rs2000: add m88rs2000_set_carrieroffset
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Set the carrier offset correctly using the default mclk values.

Add function m88rs2000_get_mclk to calculate the mclk value
against crystal frequency which will later be used for
other functions.

Add function m88rs2000_set_carrieroffset to calculate
and set the offset value.

variable offset becomes a signed value.

Register 0x86 is set the appropriate value according to
remainder value of frequency % 192857 calculation as
shown.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Set the return variable to an error code as done elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>