Commit 84f57d9e ("tty: serial/samsung: fix modular build") fixed
build issues when the driver was built as a module. One of those was
that printascii is only accessible when the driver is built-in.

But there is no need to check for defined(CONFIG_DEBUG_LL) since the
SERIAL_SAMSUNG_DEBUG Kconfig symbol already depends on DEBUG_LL.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NKukjin Kim <kgene@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The advance of the 'read' buffer index belongs in the outer
flip buffer consume loop, with the other buffer index arithmetic.

No functional change.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Clarify flip buffer producer/consumer operation; the use of
smp_load_acquire() and smp_store_release() more clearly indicates
which memory access requires a barrier.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The maximum bitrate supported depends on the clock rate used in BRG.
This is stored in port.uartclk during probe. Respecting the 16x
oversampling higher bitrates can be supported.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For now this improvement is only used with TX DMA transfers. The data
width must be set properly when configuring the DMA controller. Also
the FIFO configuration must be set to match the DMA transfer data
width:
TXRDYM (Transmitter Ready Mode) and RXRDYM (Receiver Ready Mode) must
be set into the FIFO Mode Register. These values are used by the
USART to trigger the DMA controller. In single data mode they are not
used and should be reset to 0.
So the TXRDYM bits are changed to FOUR_DATA; then USART triggers the
DMA controller when at least 4 data can be written into the TX FIFO
througth the THR. On the other hand the RXRDYM bits are left unchanged
to ONE_DATA.

Atmel eXtended DMA controller allows us to set a different data width
for each part of a scatter-gather transfer. So when calling
dmaengine_slave_config() to configure the TX path, we just need to set
dst_addr_width to the maximum data width. Then DMA writes into THR are
split into up to two parts. The first part carries the first data to
be sent and has a length equal to the greatest multiple of 4 (bytes)
lower than or equal to the total length of the TX DMA transfer. The
second part carries the trailing data (up to 3 bytes). The first part
is written by the DMA into THR using 32 bit accesses, whereas 8bit
accesses are used for the second part.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Depending on the hardware, TX and RX FIFOs may be available. The RX
FIFO can avoid receive overruns, especially when DMA transfers are
not used to read data from the Receive Holding Register. For heavy
system load, The CPU is likely not be able to fetch data fast enough
from the RHR.

In addition, the RX FIFO can supersede the DMA/PDC to control the RTS
line when the Hardware Handshaking mode is enabled. Two thresholds
are to be set for that purpose:
- When the number of data in the RX FIFO crosses and becomes lower
  than or equal to the low threshold, the RTS line is set to low
  level: the remote peer is requested to send data.
- When the number of data in the RX FIFO crosses and becomes greater
  than or equal to the high threshold, the RTS line is set to high
  level: the remote peer should stop sending new data.
- low threshold <= high threshold
Once these two thresholds are set properly, this new feature is
enabled by setting the FIFO RTS Control bit of the FIFO Mode Register.

FIFOs also introduce a new multiple data mode: the USART works either
in multiple data mode or in single data (legacy) mode.

If MODE9 bit is set into the Mode Register or if USMODE is set to
either LIN_MASTER, LIN_SLAVE or LON_MODE, FIFOs operate in single
data mode. Otherwise, they operate in multiple data mode.

In this new multiple data mode, accesses to the Receive Holding
Register or Transmit Holding Register slightly change.

Since this driver implements neither the 9bit data feature (MODE9 bit
set into the Mode Register) nor LIN modes, the USART works in
multiple data mode whenever FIFOs are available and enabled. We also
assume that data are 8bit wide.

In single data mode, 32bit access CAN be used to read a single data
from RHR or write a single data into THR.
However in multiple data mode, a 32bit access to RHR now allows us to
read four consecutive data from RX FIFO. Also a 32bit access to THR
now allows to write four consecutive data into TX FIFO. So we MUST
use 8bit access whenever only one data have to be read/written at a
time.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch replaces the UART_PUT_*, resp. UART_GET_*, macros by
atmel_uart_writel(), resp. atmel_uart_readl(), inline function calls.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch updates macro definitions in atmel_serial.h to fit the
80 column rule.

Please note that some deprecated comments such as "[AT91SAM9261 only]"
are removed as the corresponding bits also exist in some later chips.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a new DT property, "atmel,fifo-size", to enable and set
the maximum number of data the RX and TX FIFOs can store on FIFO capable
USARTs.

Please be aware that the VERSION register can not be used to guess the
size of FIFOs. Indeed, for a given hardware version, the USARTs can be
integrated on Atmel SoCs with different FIFO sizes. Also the
"atmel,fifo-size" property is optional as older USARTs don't embed FIFO at
all.

Besides, the FIFO size can not be read or guessed from other registers:
When designing the FIFO feature, no dedicated registers were added to
store this size. Unsed spaces in the I/O register range are limited and
better reserved for future usages. Instead, the FIFO size of each
peripheral is documented in the programmer datasheet.

Finally, on a given SoC, there can be several instances of USART with
different FIFO sizes. This explain why we'd rather use a dedicated DT
property than use the "compatible" property.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

task_pgrp requires an rcu or tasklist lock to be obtained if the returned pid
is to be dereferenced, which kill_pgrp does. Obtain an RCU lock for the
duration of use.
Signed-off-by: NPatrick Donnelly <batrick@batbytes.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The XR17V35X UART needs the ECB bit set in its XR_EFR
register to enable access to IER [7:5], ISR [5:4], FCR[5:4],
MCR[7:5], and MSR [7:0].

Also reset the IER register to mask interrupts after access
to all bits of this register has been enabled.

This makes my 8-port XR17V35X working with the in-kernel
serial driver.

Cc: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: NJoerg Roedel <jroedel@suse.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Reviewed-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

An already-active sender can swamp the interrupt handler with
"too much work" if the rx interrupts are enabled when the fifo is
disabled and operating in single-byte mode.

Defer rx and line status interrupt enable until after the fifos
are enabled in set_termios(), but at least initialize the shadow
IER value with the interrupts which will be enabled.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We use __u8 in linux/gsmmux.h, so include linux/types.h to have that
defined.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit ed71871b ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override

However recent updates to core, specifically ebc5e200 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3f
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.

Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: NNoam Camus <noamc@ezchip.com>
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor base port operations into new file; 8250_port.c.

Legacy irq handling, RSA port support, port storage for universal
driver, driver definition, module parameters and linkage remain in
8250_core.c

The source file split and resulting modules is diagrammed below:

  8250_core.c ====>   8250_core.c __
              \                     \
               \                     +-- 8250.ko (alias 8250_core)
                \     8250_pnp.c  __/     (universal driver)
                 \
                  =>  8250_port.c __
                                    \
                                     +-- 8250_base.ko
                      8250_dma.c  __/     (port operations)
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the UART has been in use before this driver was loaded, IRQs might be
active and get fired as soon as we set the handler, which will crash
in the spin_lock_irqsave(&sport->port.lock, flags) because port.lock is
not initialized until the port is added at the end of probe.
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To prevent problems with interrupt latency, and due to the fact, that
the error will be counted anyway (icount.overrun), the dev_err is simply
removed.

Background:
If an rx-fifo overflow occurs a dev_err message was called in interrupt
context. Since dev_err messages are written to console in a synchronous way
(unbuffered), and console may be a serial terminal, this leads to a
highly increased interrupt-latency (several milliseconds).
As a result of the high latency more rx-fifo overflows will happen, and
therefore a feedback loop of errors is created.
Signed-off-by: NManfred Schlaegl <manfred.schlaegl@gmx.at>
Acked-By: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As can be seen in function uart_insert_char (serial_core) the element
buf_overrun of struct uart_icount is used to count overruns of
tty-buffer.
Added support for counting of overruns in imx driver analogue to
serial_core.
Signed-off-by: NManfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Disable interrupts before requesting them in order to fix a kernel oops
after lauching a kernel via kexec.

Tested on a imx6sl-evk board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Being a soft core, it can be located not only on PPC or Microblaze
platforms.

Since the driver already does endianness detection we only need to
change the Kconfig to use it in other arches.

This is also done in other softcores as xilinx-spi.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

SysRq support activation depends on CONFIG_SERIAL_STM32_USART_CONSOLE, but
this config flag does not exists.

This patch fix this by depending on the valid config flag, which is
SERIAL_STM32_CONSOLE.
Reported-by: NAndreas Ruprecht <andreas.ruprecht@fau.de>
Signed-off-by: NMaxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While UART work in DMA mode, function start_rx will request descriptor
from DMA engine, if there is no left descriptor UART, driver will give
err logs "DMA slave single fail".

currently start_rx is called in set_termios function, so everytime, port
setting will call start_rx once.

Now put start_rx in startup, it will be called once while open the port.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

when UART works in DMA mode and left bytes in rx fifo less than
a dma transfer unit, DMA engine can't transfer the bytes out
to rx DMA buffer. so it need a way to fetch them out and
flush them into tty buffer in time.

in the above case, we want UART switch from DMA mode to PIO mode and
fetch && flush bytes into tty layer buffer until rxfifo become empty,
after that done let UART switch from PIO mode back to DMA mode.
(record as method1)

method1 result in the next receive result wrong. for example in PIO part
of method1, we fetched && pushed X1...X3 bytes, when UART rxfifo newly
received Y1...Y4 bytes, UART trigger a DMA unit transfer, the DMA unit's
content is X1...X3Y1 and rxfifo fifo status is empty, so X1X2X3 pushed
twice by PIO way and DMA way also the bytes Y2Y3Y4 missed. add rxfifo
reset operation before UART switch back to DMA mode would resolve the
issue. ([method1 + do fifo reset] record as method2)

before the commit, UART driver use method2. but methd2 have a risk of
data loss, as if UART's shift register receive a complete byte and
transfer it into rxfifo before rxfifo reset operation the byte will
loss.

UART and USP have the similar bits CLEAR_RX_ADDR_EN(uart)/FRADDR_CLR_EN(usp),
When found UART controller changing I/O to DMA mode, UART controller
clears the two low bits of read point (rx_fifo_addr[1:0]).
when enable the bit + method1(record as method3), in above example
the DMA unit's content is X1...X3Y1 and there are Y2Y3Y4 in rxfifo by
experiment, we just push bytes in rx DMA buffer.

BTW, the workaround works only for UART receive DMA channel use SINGLE
DMA mode.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The implementation of cris_console_device() is exactly the same as
uart_console_device(), so let's switch to use uart_console_device().
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NNiklas Cassel <nks@flawful.org>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

OMAP h/w-assisted IXON flow control is borked. The transmitter becomes
stuck if XON is never received; clearing the fifos or resetting the
rx flow control bits has no effect.

Remove auto-IXANY as well, since without auto-IXON, it has no purpose.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Due to Advisory 21 as documented in AM437x errata document,
UART module cannot be disabled once DMA is used. The only
workaround is to softreset the module before disabling it.

DRA7x UARTs are compatible to AM437x UARTs in terms of
this errata and prescribed workaround.

Enable usage of workaround for this errata on DRA7x SoCs.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

AM335x, AM437x and DRA7x SoCs have an errata[1] due to which UART
cannot be idled after it has been used with DMA.

OMAP3 has a similar sounding errata which has been worked around
in a2fc3661 ("ARM: OMAP3: Use manual idle for UARTs
because of DMA errata"). But the workaround used there does not
apply to AM335x, AM437x SoCs.

After using DMA, the UART module on these SoCs must be soft reset
to go to idle.

This patch implements that errata workaround. It is expected that
UART will be used with DMA so no explicit check for DMA usage
has been added for errata applicability.

MDR1 register needs to be restored right after soft-reset because
"UART mode" must be set in that register for module wake-up on AM335x
to work. As a result, SCR register is now used to determine if
context was lost during sleep.

[1] See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
    http://www.ti.com/lit/er/sprz408b/sprz408b.pdfSigned-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use of of_machine_is_compatible() for handling AM335x specific
"DMA kick" quirk in 8250_omap driver makes it ugly to extend the
quirk for other platforms. Instead use a new compatible.

The new compatible will also make it easier to take care of
other quirks on AM335x and like SoCs.

In order to not break backward DTB compatibility for users of
8250_omap driver on AM335x based boards, existing use of
of_machine_is_compatible() has not been removed.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The silicon errata[1] workaround implemented in a follow-on
patch, "serial: 8250_omap: workaround errata on disabling
UART after using DMA", requires MDR1 register programming.

Extract MDR1 register update into helper function,
omap8250_update_mdr1() to help with that.

[1] Advisory 21 in http://www.ti.com/lit/er/sprz408b/sprz408b.pdfSigned-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The compatible "ti,am4372-uart" is used in arch/arm/boot/dts/am4372.dtsi
but not documented. Add necessary documentation.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

omap_device infrastructure has a suspend_noirq hook which
runtime suspends all devices late in the suspend cycle (see
_od_suspend_noirq() in arch/arm/mach-omap2/omap_device.c)

This leads to a NULL pointer exception in 8250_omap driver
since by the time omap8250_runtime_suspend() is called, 8250_dma
driver has already set rxchan to NULL via serial8250_release_dma().

Make an explicit check to see if rxchan is NULL in
runtime_{suspend|resume} hooks to fix this.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fintek chip can be configured for io addresses different than the standard.

Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: NPeter Hong <peter_hong@fintek.com.tw>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Chip can be configured to use entry key different than 0x77. Try all the
valid keys until one gives out the right chip id.
Reported-by: NPeter Hong <peter_hong@fintek.com.tw>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are some chips with the same interface but different chip ip.
Reported-by: NPeter Hong <peter_hong@fintek.com.tw>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fintek chip can be connected at address 0x4e and also 0x2e.
Add some logic to find out the address of the chip.
Reported-by: NPeter Hong <peter_hong@fintek.com.tw>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Save the port index and the line id in a private structure.
Reported-by: NPeter Hong <peter_hong@fintek.com.tw>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In little endian cases, macro htons unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_htons and htons expand directly to the same expression.
So, replace __constant_htons with htons with the goal of getting
rid of the definition of __constant_htons completely.

The semantic patch that performs this transformation is as follows:

@@expression x;@@

- __constant_htons(x)
+ htons(x)
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>